October 30 day minimalist SAK challenge
-
Agreed. I'm also surprised doing this challenge just how much can be accomplished with a simple one or two layer SAK. A few times I've wanted the smaller pen knife blade, or nail file... But overall for EDC, it sure covers most needs.
Call me impressed, coming from a mainly Leatherman pov.
-
Day 12:
(Attempting it ALL single layer!)A few more photos, not to show the knife as much as how (one method) to cut a small machine screw and have the end threads work well afterward. The machine screws on the pantry door pulls have been about 1/4" (6mm) too long for eons.

Drawer and door pulls have broad heads that are very flat so that they don't dig through the wood or stand proud from the back. They're also typically a combination Phillips and flat tip so the installer, who would invariably have the wrong tipped driver in hand, doesn't have to go back to his toolbox for the proper one. Because of the desirable head profile, it's better to reuse the screws whenever possible than try to get new ones from the hardware store. I'm going to cut about 1/4" off these and reuse them. In the effort long ago to get these to pull the handle flush, they were tightened by someone else using a power driver. The 3-D Phillips on the Apprentice can take the torque to get them loose.

Once loose, I can spin them out using the flat-tip. :)

Once both screws are out, the next step is cutting them down. No tool on any SAK can do this very effectively. The metal saw on a Craftsman or Champion Plus could be used, but that's still much less than ideal and it requires holding the screw to make the cut which is difficult at best without damaging threads (been there, done that, with hack saw and vise). For small machine screws I have this nifty Waldom hardened steel wire stripper and lug crimper that also has a machine screw shear for small numbered screws. These are #8 with National Coarse thread pitch (32 tpi). Thought at first it might be #10 National Extra Fine (also 32 tpi) but they were too loose in the #10x32 hole.

Get about 1/4" protruding from the other side and it's ready to be sheared off.

A bit of a squeeze and the end of the screw is nipped off as nice as you please. Much easier than using nuts, a vise and a hack saw!

Experience has taught me it's a good idea to chamfer the end of the screw before chasing its threads and backing it out of the tool. This metal hand file was handy (I'd been using it for other tasks recently). A grinder also can be used, and I've used one on large bolts cut with a hacksaw, but care must be taken not to overheat the screw. Don't need a grinder for a soft steel screw this small.

With the end chamfered, I chase the threads by working the screw end back and forth through the threads in the cutting tool. Chasing the threads is why you always put a nut onto a screw or bolt, or a thread cutting die, if not using a threaded cutting tool. Backing it out is much easier than trying to get it started just after being cut. The Apprentice's Phillips is ideal for this.

Once both screws were shortened, I put them all the way into the handle to see if they would thread easily, and to check against the door edge to ensure they were sufficiently shorter, which turned out to be just barely, but that's OK. Just barely short enough works.

They now tighten up flush on the back side, with the Phillips ideal for giving them some torque to keep from coming loose.

And the handle is now flush and tight on the front side!


A better look at the (several decades old) Waldom crimping tool with the Apprentice fabricated earlier this year from a Waiter and "thrashed beyond all recognition" Tinker. Waldom still makes this tool, which speaks volumes about its utility. The Apprentice is a Cellidor Bantam with backside Phillips. Perhaps that's why it was discontinued, as it was between a Bantam and a Small Tinker with the other two proving more popular. Could have just shown the Apprentice in use, but thought showing how the screws were shortened would be helpful for anyone who hasn't done it before.

John
-
That Waldom crimper is fantastic!

Thanks for Sharing, John
-T -
16/30
Switching from the Executive back to the Classic for work tomorrow.I fileted the catfish, thought about trying a SAK, but the fish were too big. I used a dedicated filet knife (USA Schrade)

Sent from my SAMSUNG-SM-N900A using Tapatalk
-
Day 17:
BantamRambler for the office today:
-
Day 16
-
Great pics all!

Day 17: GAK

-
@Oxford_Guy said:
Day 17:Bantam for the office today:

Bantam?

-
Day 17:
Bantam for the office today:

Bantam?


-
T14 day 17:
Swisscards are lecture hall friendly


-
Day 17:
Bantam for the office today:

Bantam?


It's what you get when you forget to take it out of your pocket and it goes through the laundry.
Just a random rambling thought. -
Day 17:
Bantam for the office today:

Bantam?

Oops!

-
Day 17
WP_20161017_010 by magpie2112, on Flickr -

(;,;)(;,;)(;,;) -
DAY 17

-
Did one week and then got real busy.
I will try keep it to a minimum but I'm out.
-
Nice pic Twiglet!

You too Shamus - Mogimalist challenge success!

-
Thanks Mags, yours too!

Those appear to be chestnuts, but they could also be polished road apples, I'm going to assume the former.

-
@twiliter said:
Thanks Mags, yours too!
Those appear to be chestnuts, but they could also be polished road apples, I'm going to assume the former.

They are Horse Chestnuts or as we call them here, Conkers. In Autumn we play a game where, (using the mighty awl), you make a hole through the conker and thread it on a length of string. Two foes face each other and take turns to smash their opponents conker. The victor's conker then 'levels up' to a higher number (say from a sixer to a sevener) depending on how many victories it has under its belt.
It's what passes for entertainment here in Blighty.
What are road apples?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login