October 30 day minimalist SAK challenge
-
The Soldier helped me get to my beer for today's dinner. For not being a cap lifter it does a remarkably good job at it and it's quite possibly better at lifting caps than opening cans (see my earlier picture of the result).
Good looking streak tartare! One of my favourite things to order when I'm in Paris (I visit quite often as my wife's family live there)
-
The Soldier helped me get to my beer for today's dinner. For not being a cap lifter it does a remarkably good job at it and it's quite possibly better at lifting caps than opening cans (see my earlier picture of the result).
I'd send that burger back to the kitchen, it looks a little under- cooked!
-
@Alan K. said:
Day 20
The Soldier helped me get to my beer for today's dinner. For not being a cap lifter it does a remarkably good job at it and it's quite possibly better at lifting caps than opening cans (see my earlier picture of the result).
I'd send that burger back to the kitchen, it looks a little under- cooked!

-
@Alan K. said:
Day 20
The Soldier helped me get to my beer for today's dinner. For not being a cap lifter it does a remarkably good job at it and it's quite possibly better at lifting caps than opening cans (see my earlier picture of the result).
I'd send that burger back to the kitchen, it looks a little under- cooked!
If you have enough beer, how well the burger and egg on top of it are cooked does't matter.
-
Day 21:
Elinox Gourmet for today (but Victoria Student for this evening)
So that's not both, but one, and then the other :)
-
Day 20
-
Day 21, electrician!

-
@glenfiddich1983 said:
Day 21, electrician!
electrician club! -
Day 21
Finally something different from the recent rotation, received a post-2008 Wenger Stand Issue in the mail yesterday (previously owned by Basilio), can see this one getting more carry than my Soldier, as will be able to attach a Tec P7 clip to the bail:

-
@Oxford_Guy said:
Day 21Finally something different from the recent rotation, received a post-2008 Wenger Stand Issue in the mail yesterday (previously owned by Basilio), can see this one getting more carry than my Soldier, as will be able to attach a Tec P7 clip to the bail:

Nice! The hollow rivet is the best of awl worlds as you can decide if you want a bail or not - very comfy in the hand too.

-
@Oxford_Guy said:
Day 21Finally something different from the recent rotation, received a post-2008 Wenger Stand Issue in the mail yesterday (previously owned by Basilio), can see this one getting more carry than my Soldier, as will be able to attach a Tec P7 clip to the bail:


I have a 2004 and they are excellent! Bail or split ring, I do like something to hang a short fob on.
-
Day 21 - 3 whole weeks! 3/4 or 75% of the way through. Although I like more layers on my EDC normally, I have a new respect for the basic tools, especially in the more robust guise of the SI.
WP_20161021_004 by magpie2112, on Flickr -
Day 21/30
Time for a touch up on the GID Classic.
Sent from my SAMSUNG-SM-N900A using Tapatalk
-
Day 21
-
<u>Day 17</u>:
(Attempting it ALL single layer!)My grandfather clock's beat error has been substantially off, and it's like hearing fingernails scratching across a blackboard. In a mechanical clock or watch with an escapement, the beat error is the time difference between a Tick-->Tock and a Tock-->Tick. Would be too much to explain here how this is regulated in a watch or mantle type clock with a Swiss Lever (or similar) escapement. In a pendulum clock, it's regulated by making the movement's escapement vertical, so that the Tick-->Tock-->Tick-->Tock is evenly spaced. Instead, my clock has been very obviously running Tick->Tock---->Tick->Tock---->Tick->Tock.

This should be easy by adjusting the leveler jack screws on the bottom of the clock. The first step is stopping the clock and having its door unlocked so I can stop the pendulum and weights from banging into each other and the chimes while I adjust the leveling. Unfortunately I cannot find the key. It's not in the music cabinet or the wash stand on each side of the clock. Fortunately I'm carrying the Bantam today and it's combo opener isn't just for opening bottle and cans, it can manipulate the tumbler lever and bolt to open the larger of these simple, single lever furniture mortise locks.

The door opened easily and I should be able to lock it again just as easily. The key will eventually turn up somewhere in the several stashes of keys around the house. It's undoubtedly hidden in a safe place, so safely hidden that I've not been able to find it.
Next step is setting a level on top of the clock. It won't necessarily show the top of the clock level when the beat rate is even as the clock works being perfectly vertical regulates that, not the clock case. It can be used to show how much relative change has been made in adjusting the tilt of the clock. I put two short 2x4 blocks on top to raise a short level enough to be seen above the facade. But wait, there's something on top of the clock! What have we here? It's the key to the clock door!! Perhaps the most logical place to put the key, my brain is not functioning well today.


At least I know now the Mighty Alox Bantam combo opener can be used to open some simple locks. I quickly decide it was a "proof of concept" demonstration, and not an act of desperation. That's my story now, and I'm sticking to it.
The level is now on top of the clock.
Now to adjust the leveling jack screws on the bottom. I know from watching the pendulum and observing the shorter time between beats occurs when the pendulum swings to the right, that the clock must be tilted to the right slightly. The jack screws on the right are all the way flush. A check on the jack screws on the left shows them already fully extended. The leveling jack screws aren't long enough to tilt the clock sufficiently. This will have to be done Old School using thin wedged shims, the kind that's used between floor joists and sub-flooring to stop floor squeaks (invariably caused by one or more flooring nails rubbing up and down in a joist nail hole).

I won't worry about their length for now as they're hidden around the side of the wash stand to the left of the clock (which is in a room corner). Adjusting how much the shims are pushed under the left edge of the clock regulates the beat error, and I work at it until it sounds as if it's been reduced to zero, or nearly so. If you look on the left side in the photo above, you can see the edge of the black left rear jack screw adjustment wheel standing out from the base of the clock. The door can be locked again, this time using the key, and I'll put it in the same safe location it was in before, on top of the clock.

Now to set up an app on my iPad to measure the beat rate and beat error. The beat rate is how fast or slow the clock is running. It should be exactly 3600 beats per hour (one every second; the typical rate for a grandfather size pendulum clock). Beat rate is regulated by location of the pendulum weight on the pendulum (the big round disc on this clock; it has much more mass than it appears to). Its height is adjusted using a thumb wheel on a very finely threaded vertical pendulum rod. Raise the weight and the beat rate increases; lower it and the beat rate decreases. While the app will tell me the beat rate, the issue was the beat error. The beat rate was nearly dead on. Correcting that may shift the beat rate slightly, but watching the clock for 3-5 days to see if it's fast or slow, and by how much, will work better. This app can also be used for watches and mainspring type clocks with Swiss Lever (or similar) escapements, so it has lift angle and amplitude are meaningless for a pendulum clock as the amplitude is set by clock design.

It needs to gather sufficient sample data, so I'll let it run for at least several hours. The Alox Bantam came through once again, with its Victorinox combo blade that can open some locks in addition to cans and bottles. Wouldn't advertise that much as law enforcement could then claim it's a "burglary tool" and promptly arrest anyone found in possession of one. :o
John
-
@jalind said:
<u>Day 17</u>:
(Attempting it ALL single layer!)My grandfather clock's beat error has been substantially off, and it's like hearing fingernails scratching across a blackboard. In a mechanical clock or watch with an escapement, the beat error is the time difference between a Tick-->Tock and a Tock-->Tick. Would be too much to explain here how this is regulated in a watch or mantle type clock with a Swiss Lever (or similar) escapement. In a pendulum clock, it's regulated by making the movement's escapement vertical, so that the Tick-->Tock-->Tick-->Tock is evenly spaced. Instead, my clock has been very obviously running Tick->Tock---->Tick->Tock---->Tick->Tock.

This should be easy by adjusting the leveler jack screws on the bottom of the clock. The first step is stopping the clock and having its door unlocked so I can stop the pendulum and weights from banging into each other and the chimes while I adjust the leveling. Unfortunately I cannot find the key. It's not in the music cabinet or the wash stand on each side of the clock. Fortunately I'm carrying the Bantam today and it's combo opener isn't just for opening bottle and cans, it can manipulate the tumbler lever and bolt to open the larger of these simple, single lever furniture mortise locks.

The door opened easily and I should be able to lock it again just as easily. The key will eventually turn up somewhere in the several stashes of keys around the house. It's undoubtedly hidden in a safe place, so safely hidden that I've not been able to find it.
Next step is setting a level on top of the clock. It won't necessarily show the top of the clock level when the beat rate is even as the clock works being perfectly vertical regulates that, not the clock case. It can be used to show how much relative change has been made in adjusting the tilt of the clock. I put two short 2x4 blocks on top to raise a short level enough to be seen above the facade. But wait, there's something on top of the clock! What have we here? It's the key to the clock door!! Perhaps the most logical place to put the key, my brain is not functioning well today.


At least I know now the Mighty Alox Bantam combo opener can be used to open some simple locks. I quickly decide it was a "proof of concept" demonstration, and not an act of desperation. That's my story now, and I'm sticking to it. The level is now on top of the clock.

Now to adjust the leveling jack screws on the bottom. I know from watching the pendulum and observing the shorter time between beats occurs when the pendulum swings to the right, that the clock must be tilted to the right slightly. The jack screws on the right are all the way flush. A check on the jack screws on the left shows them already fully extended. The leveling jack screws aren't long enough to tilt the clock sufficiently. This will have to be done Old School using thin wedged shims, the kind that's used between floor joists and sub-flooring to stop floor squeaks (invariably caused by one or more flooring nails rubbing up and down in a joist nail hole).

I won't worry about their length for now as they're hidden around the side of the wash stand to the left of the clock (which is in a room corner). Adjusting how much the shims are pushed under the left edge of the clock regulates the beat error, and I work at it until it sounds as if it's been reduced to zero, or nearly so. If you look on the left side in the photo above, you can see the edge of the black left rear jack screw adjustment wheel standing out from the base of the clock. The door can be locked again, this time using the key, and I'll put it in the same safe location it was in before, on top of the clock.

Now to set up an app on my iPad to measure the beat rate and beat error. The beat rate is how fast or slow the clock is running. It should be exactly 3600 beats per hour (one every second; the typical rate for a grandfather size pendulum clock). Beat rate is regulated by location of the pendulum weight on the pendulum (the big round disc on this clock; it has much more mass than it appears to). Its height is adjusted using a thumb wheel on a very finely threaded vertical pendulum rod. Raise the weight and the beat rate increases; lower it and the beat rate decreases. While the app will tell me the beat rate, the issue was the beat error. The beat rate was nearly dead on. Correcting that may shift the beat rate slightly, but watching the clock for 3-5 days to see if it's fast or slow, and by how much, will work better. This app can also be used for watches and mainspring type clocks with Swiss Lever (or similar) escapements, so it has lift angle and amplitude are meaningless for a pendulum clock as the amplitude is set by clock design.

It needs to gather sufficient sample data, so I'll let it run for at least several hours. The Alox Bantam came through once again, with its Victorinox combo blade that can open some locks in addition to cans and bottles. Wouldn't advertise that much as law enforcement could then claim it's a "burglary tool" and promptly arrest anyone found in possession of one. :o
John
Awesome! I have a 100 year old clock that I can't get to run fast enough. I should have you and your Bantam visit. ..;)
Sent from my SAMSUNG-SM-N900A using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login