Modding a Rebar questions
-
I have 2 modded Rebars 1 handle has the exact same configuration in both and the other handle is a bit different in both.
The side with the saw is as this. Saw, thin washer, scissors, phillips driver, thin washer and serrated blade

One of the Rebars has a plier head with replaceable cutters and the configuration on it is as this. File (diamond in this Rebar), thin washer, can opener, awl, medium flat driver, large flat driver, thin washer and plain edge blade

The other has the Wave plier head and the configuration is this. File, thin washer, awl, medium flat driver, large flat driver, can opener, thin washer and plain edge blade

I hope that some of this helps you

-
New page banana man dance

-
@Poncho65 said:
The side with the saw is as this. Saw, thin washer, scissors, phillips driver, thin washer and serrated blade
That's correct, I did the same yesterday. I noticed there's some spare space on that side for a very thin tool. I don't know, maybe I will put there needle compartment? I have more problems on the other side:
@Poncho65 said:
One of the Rebars has a plier head with replaceable cutters and the configuration on it is as this. File (diamond in this Rebar), thin washer, can opener, awl, medium flat driver, large flat driver, thin washer and plain edge blade
Again, I implement the same configuration yesterday, prior to your answer. I found that all those tools together are too thick for that side! Even without washers the axle is too short to reach the other side (I need 0.75 mm more). The only difference comparing to Poncho was that I used regular Rebar file, not the diamond one. Is it possible that diamond file is thinner than regular Rebar one?
-
The side with the saw is as this. Saw, thin washer, scissors, phillips driver, thin washer and serrated blade

That's correct, I did the same yesterday. I noticed there's some spare space on that side for a very thin tool. I don't know, maybe I will put there needle compartment? I have more problems on the other side:
@Poncho65 said:
One of the Rebars has a plier head with replaceable cutters and the configuration on it is as this. File (diamond in this Rebar), thin washer, can opener, awl, medium flat driver, large flat driver, thin washer and plain edge blade
Again, I implement the same configuration yesterday, prior to your answer. I found that all those tools together are too thick for that side! Even without washers the axle is too short to reach the other side (I need 0.75 mm more). The only difference comparing to Poncho was that I used regular Rebar file, not the diamond one. Is it possible that diamond file is thinner than regular Rebar one?
The other Rebar has the regular file and so did the other one at first. you may have to force it apart a little at first to get it all in there then tighten everything up really good almost.over tightening. Then check it to see how the tools come out and adjust them.until they come out like you want them to

The saw side shouldn't reallyhave any extra room
Unless you mean you forgot the washers the first time around. I would also over tighten it a bit and then loosen it until the tools come.out the way you want them to 
Hope this helps

-
This didn't help. The tools don't want come out now. I don't know, maybe Rebars in US have a bit slimmer screwdrivers than those in Europe...
-
When I did mine I ground some thickness off of the can opener and everything fit a lot better.
</post/1033900>
-
That is odd
I didn't grind anything on mine and everything works great ??? Sorry I couldn't be any help
Hopefully you get it sorted though 
-
I'd like to drill hole/aperture on the side of my Rebar that will serve as a bit holder. I plan to use bits made by my own, but it will be nice if that hole will be suitable also for Leatherman bits. Anyone wil be so kind and measure for me the width and thickness of those flat Leatherman bits? I don't have one to compare.

-
Reminds me, I still need a micrometer... sorry bud, I'm no help.
-
Thickness: 1/8"
Length: 1 1/4" (5/4")
Width: 9/32"Argh! Vernier calipers in Imperial gives me headaches.
-
31.75 × 7.18 × 3.18 mm 8)
-
@hiraethus said:
31.75 × 7.18 × 3.18 mm 8)Yeah, I just felt it made more sense to give the measures in Imperial since that gave such nice even numbers.
-
Hi friends! I signed up on the forum to share experiences of Rebar mod. Rebar + Wave scissors.




-
@krasutskyy said:
Hi friends! I signed up on the forum to share experiences of Rebar mod. Rebar + Wave scissors.Nice, but it is much easier to excavate scissors when they don't touch saw. Try to put the washer between saw and scissors, not between scissors and philips.
-
@krasutskyy said:
Hi friends! I signed up on the forum to share experiences of Rebar mod. Rebar + Wave scissors.Nice job and welcome to the forum.

-
Welcome to
Thanks for sharing

-
Hey fellas!
Just found your forum while I was looking stuff up. I've had a LM Kick for about 12 years or so and I was thinking about getting a Rebar to replace it. What I was wondering about was whether it's possible to replace the saw on the Rebar with a replaceable "T-shank" one such as those on the Super Tool 300 EOD or the Surge? ??? I could part with the serrated blade too if sideways clearance is an issue.Sorry if this has been asked already, I have a bit of a headache so I gave up with looking for older answers once I saw this thread, seeing as it handles the same subject and all.
Thanks in advance! :)
edit: Jesus, 4 edits in a row, should have taken a tylenol before I started posting. :ahhh -
@Skivvy Roll said:
Hey fellas!
Just found your forum while I was looking stuff up. I've had a LM Kick for about 12 years or so and I was thinking about getting a Rebar to replace it. What I was wondering about was whether it's possible to replace the saw on the Rebar with a replaceable "T-shank" one such as those on the Super Tool 300 EOD or the Surge? ??? I could part with the serrated blade too if sideways clearance is an issue.Sorry if this has been asked already, I have a bit of a headache so I gave up with looking for older answers once I saw this thread, seeing as it handles the same subject and all.
Thanks in advance! :)
edit: Jesus, 4 edits in a row, should have taken a tylenol before I started posting. :ahhhYou can make the ST300 EOD blade exchanger work, but it requires some work.....
http://forum.multitool.or...ex.php/topic,67918.0.html
I've got mine in a Rebar handle with the SE blade, awl, large flat driver/pry tool, and mini bit driver from the Wave.
-
hi guys, i just got myself a new rebar and i really can't wait to do some modding to the tool. was thinking of swapping the scissors from my wave over to the rebar. kinda new to the modding scene. is there anything i need to pay extra attention to when moving the scissors over? any clearance issue? good day!!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
Anyway, thank you very much!