The test.
-
Very interesting Gene. Thanks for doing this.

-
+1

From my limited observations, I'd say the serrated beast is better at hacking or to put it in another way, it works best for tasks where precision is not of paramount importance. Slashing is another thing it does well, which makes sense for a soldier's knife.
I've cut a bunch of fern with it and it worked great. No idea about dulling though, I'm very interested to hear your findings

-
Nice

Looking forward to more tests. Will you also do a sharpening comparison?
-
@Etherealicer said:
Nice
Looking forward to more tests. Will you also do a sharpening comparison?
What type of sharpening comparison did you have in mind? To be honest both blade's are hair shaving sharp when I start a test. (Yes you can shave with the Vic serated blade just be careful.)

-
What I've read is serrated edges don't have to be as sharp as PE to still cut. When the points may dull the scalloped part will retain its edge and still be able to perform.
@gene stoner said:
Last for now but maybe the most interesting is the rubber mat. For speed the serated won but the cuts where not as clean as the PE. I did some slicing and push cuts. The chisle grind PE on the solder cut as clean as the PE Trekker but I think the Trekker PE was just a little easier to control. This exercise dulled both blade's but even dull both blade's still sliced through the hard rubber.
So far I can't really say one is better then the other.I'd be curious to see the tests continued after the edges were noticeably dull. As mentioned the points on the SE may feel dull yet still perform. I'd be interested how long the PE would perform once the edge was feeling dull.
Good job and thank you.

-
Nice

Looking forward to more tests. Will you also do a sharpening comparison?
What type of sharpening comparison did you have in mind? To be honest both blade's are hair shaving sharp when I start a test. (Yes you can shave with the Vic serated blade just be careful.)
It would be interesting what kind of setup you use and how long it takes.
I'm not very good at sharpening, but I can work with PE blades. Serrated blades take me forever.
-
@Aloha007 said:
What I've read is serrated edges don't have to be as sharp as PE to still cut. When the points may dull the scalloped part will retain its edge and still be able to perform.Last for now but maybe the most interesting is the rubber mat. For speed the serated won but the cuts where not as clean as the PE. I did some slicing and push cuts. The chisle grind PE on the solder cut as clean as the PE Trekker but I think the Trekker PE was just a little easier to control. This exercise dulled both blade's but even dull both blade's still sliced through the hard rubber.
So far I can't really say one is better then the other.I'd be curious to see the tests continued after the edges were noticeably dull. As mentioned the points on the SE may feel dull yet still perform. I'd be interested how long the PE would perform once the edge was feeling dull.
Good job and thank you.

This is exactly why steak-knives are serrated. The teeth get blunted quickly, cutting into porcelain, but the knife stays sharp in-between.
-
Nice

Looking forward to more tests. Will you also do a sharpening comparison?
What type of sharpening comparison did you have in mind? To be honest both blade's are hair shaving sharp when I start a test. (Yes you can shave with the Vic serated blade just be careful.)
It would be interesting what kind of setup you use and how long it takes.
I'm not very good at sharpening, but I can work with PE blades. Serrated blades take me forever.
The Vic serated blade is easier then most serrated blade's on the market. Rarely do I use anything more then an old butcher steel. Later today I'll try to give pics and details on angle and such.

-
How about food tasks...bread, tomaters etc...are you gonna cut the cheese? ::)
-
Some people have asked how I sharpen my 111mm chisel grind serrated blade?
I'll try to explain.
Hold the knife at about30 degrees + or -on the sharpened side. Use a round sharpener or the corner of a square one. Pass the blade 5 to 7 times then reverse to the non sharpened at about 5 degrees + or - lightly do 1 to 3 swipes. The only reason you touch up the non sharpened side is to remove the burrs. Don't try to sharpen the nonsharpened side just remove the burrs!
Repeat till you're done


-
Look what my walk brought me today. Some rubber weather striping, a couple of leather gloves and a bunch off heavy nylon strap. As soon as I get a chance I'll stat cutting. Can't promise it'll be today but I'll try.

-
Some interesting info.

-
Today we have a clear winner. I started out cutting wet Lether gloves. Both knifes started out razor sharp but after a little more then half way the PE Trekker started to fail. The serated Soldier finished the PE glove then tore up it's own glove. Tords the end of the glove test the plain section of the serrated blade became almost useless because it got so dull but the serations still sawed through but it took more force to do it.
This next test I did NOT sharpen eather blade. Rubber weather striping folded to four layers. The PE cut it but it took a lot more force to cut. The serated edge was easyer but still took a lot more force. At this point the PE section on the Soldier was perty useless giving you only the serrations to saw through it. At This point the serrations are clearly working.
Next came wet nylon strap. Folding in half to cut both blade's cut the wet nylon but the serations did a better job. So let's make it more interesting. I tied a knot in the strap and tried to cut it with the PE. The PE failed to cut the knot. It didn't even make it through the first layer. This knife is done. The serrations on the Soldier where able to saw through three more knots before I stopped. I'll be spending all afternoon sharpening both knifes but even dull the serations worked.



-
In my experience serrated are much better option when cutting anything on a hard surface like porcelain (or china or however it is called and/or spelled). I see a lot of people using knives like the Laguiole for eating but I really don't like the idea because of their non serrated edge. To me that is where serrated really shines, but it's just my opinion.
-
This is great information! I really appreciate your willingness to put the blades to the test; especially since sharpening serrations is not an easy task ( I think). Up until now, I didn't think I'd see much use for serrations (especially fine work). Thanks!

-
This firs pic shows here the PE failed to cut. The PE section on the serrated was done at this point but the serations kept going and going. Sorry some of pics suck I'm using a broken tablet to do this.


-
I'm thinking I should do some carving and fire prep to help give an idea of outdoor survival/ Bushcraft duties. What do you guys think? What do you want me cut? Give me what you think may be real world cutting task?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login