ST 300 owners club
-
Thanks for all your advises and replies. I eventually get a rebar instead of St. I tried them both on my hand in a retail shop here but the st is just as bulky as the surge on my hand when sktetch though indeed a lot lighter. And I don't know why it digs my ring finger badly as I put he finger behind the handle to open it up. Maybe coz of the lock location... And the fact that I have really small hands. The surge is fine on my hand but the St really dig my finger badly. I tried a rebar and found it super compact light, tough and comfortable. Anyway, thanks and you guys are really kind to answer all my questions.
-
Congrats on getting the Rebar, it is a fine tool

-
-
Right before we discussed about the tools wiggle on the ST300. I have got the rebar and I have been using it for two days. I have been looking at the rebar for a whole night trying to find out the wiggle point. Assuming the rebar share the same built of ST300, the reason for tool wiggle on the ST300 shall be the same.
The wiggle is not caused by the screws but the lock. There is a small round hole on the handle housing the pivot point of the lock. But you can see that this little hole is not completely round, it's slightly oval. Looks like it is not a production QC problem as the oval is smooth. It is supposed to be something by design. And in the back of the handle there is a notch accommodating the bar of the lock. You can also see that the notch is slightly larger than the bar in the lock by maybe 0.2mm. Then, when tools are engaged, and when you push the tool forward, the notch in the tool will push the whole lock plate forward to the allowance in the handle notch or the end of the oval hole whichever stop the lock plate first. I hope I do discribe correctly. That means, this wiggle is by design allowed by LM. So, it is not LM's qc error in the wiggle issue but LM design to have so. I don't really understand the reason to do that. Cutting down the scrap rate maybe .. I don't know. So, they all wiggle, as long as there are not vertical play, then get over it.
It is base on my observation to the rebar and I don't have other box style LM to compare. Will you check your ST300 or Rebar and correct me if I am wrong. Thanks.
-
@aurabattler said:
Right before we discussed about the tools wiggle on the ST300. I have got the rebar and I have been using it for two days. I have been looking at the rebar for a whole night trying to find out the wiggle point. Assuming the rebar share the same built of ST300, the reason for tool wiggle on the ST300 shall be the same.The wiggle is not caused by the screws but the lock. There is a small round hole on the handle housing the pivot point of the lock. But you can see that this little hole is not completely round, it's slightly oval. Looks like it is not a production QC problem as the oval is smooth. It is supposed to be something by design. And in the back of the handle there is a notch accommodating the bar of the lock. You can also see that the notch is slightly larger than the bar in the lock by maybe 0.2mm. Then, when tools are engaged, and when you push the tool forward, the notch in the tool will push the whole lock plate forward to the allowance in the handle notch or the end of the oval hole whichever stop the lock plate first. I hope I do discribe correctly. That means, this wiggle is by design allowed by LM. So, it is not LM's qc error in the wiggle issue but LM design to have so. I don't really understand the reason to do that. Cutting down the scrap rate maybe .. I don't know. So, they all wiggle, as long as there are not vertical play, then get over it.
It is base on my observation to the rebar and I don't have other box style LM to compare. Will you check your ST300 or Rebar and correct me if I am wrong. Thanks.
Yes the hole for the lock tab on mine is oval as well and I think you are correct that it may be by design and would allow less tight tolerances on the many different tools that go into the Rebar thus less waste
I think that the 300 (not with me) has a similar oval hole if I am not mistaken and I am sure it is the same way for the same reason 
-
-
Nice pic Steve.

-
Thanks guys

-
New page banana man dance

-
-
Getting ready to join the ST300 club...pics to follow!! :ahhh :ahhh :ahhh
-
@Barry Rowland said:
Getting ready to join the ST300 club...pics to follow!! :ahhh :ahhh :ahhhExcited for you
Can't wait 
-
-
Next to most reg sized MTs the 300 is a beast :o Especially next to the Rebar because it is essentially a small version of the 300

Really can't wait to hear your thoughts on it and see what you think about the size difference

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

Great shot Steve 



