Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Pin Sizes

Scheduled Pinned Locked Moved The Mod Squad
13 Posts 1 Posters 12.7k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Pin Sizes
Pin Sizes
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Craig T Offline
    Craig T
    Posts: 17
    Craig T Offline
    Craig T
    wrote on last edited by
    Quote Reply

      I am preparing to mod a SAK Outrider and have been looking for the pin sizes. This is almost certainly often repeated info. I have been searching but have not found the answer.

      This is listed in "A "how-to" for basic SAK mods"
      91mm: 2.5mm outer, 2.2mm (2.25) center
      84mm: 2.25mm for all
      74mm: 2mm modern, 1.5mm older
      58mm: 1.5mm

      The Outrider is 111 mm. Are 91mm and larger all the same pin sizes?

      Also, what the favorite sources for brass pins stock?

      Sorry if these are often asked annoyingly simple questions. Sometimes I just don't seem to find info that other folk find easily.

      As always, any input is most appreciated.

      1 Reply Last reply
      • jaya_man Offline
        jaya_man
        Global Moderators
        Posts: 9,012
        jaya_man Offline
        jaya_man
        Global Moderators
        wrote on last edited by jaya_man
        #1 Quote Reply

          111mm liner lock models follow the 93mm pin sizes, ie: 3mm outer and 2.5mm inner.

          111mm slide lock models follow the 91mm pin sizes...

          Info can be found in this thread:

          /topic/48172

          I think it is also part of the list of mod guides in the sticky section under The Mod Squad.

          Sent from my iPhone using Tapatalk

          1 Reply Last reply
          • Craig T Offline
            Craig T
            Posts: 17
            Craig T Offline
            Craig T
            wrote on last edited by
            #2 Quote Reply

              Thanks jaya_man for the info and thread link. Very helpful info.

              If I decide to proceed with adding parts from a 111mm liner lock (3 / 2.5mm pins) into the Outrider 111mm slide lock (2.5 / 2.2mm pins) I will need to drill out the Outrider components.

              What type of drill bits have you folk found to do the best job at drilling the hard steel? High speed steel? Carbide tipped? Solid carbide? Carbide straight flute?

              Has anyone gone in the other direction and put a bushing in the 3mm holes to reduce to 2.5mm?

              1 Reply Last reply
              • jaya_man Offline
                jaya_man
                Global Moderators
                Posts: 9,012
                jaya_man Offline
                jaya_man
                Global Moderators
                wrote on last edited by
                #3 Quote Reply

                  No worries...

                  My only experience is using HSS bits (waisted a lot) for reducing pivot hole size on 91mm scissors so that I can implant them on 84mm...

                  As there is not much difference between 2.5mm and 2.2mm, first had to enlarge it to 3mm, stuff the hole with brass, then redrill 2.2mm hole...

                  I have yet to find carbide bits [emoji16]

                  Sent from my iPhone using Tapatalk

                  1 Reply Last reply
                  • sLaughterMed Offline
                    sLaughterMed
                    Posts: 3,450
                    sLaughterMed Offline
                    sLaughterMed
                    wrote on last edited by
                    #4 Quote Reply

                      Honestly, I havent had any trouble with holes that were .5mm larger than the pins they rode on. Heck, Victorinox even uses the 93mm awl and pruning blade on the XAVT, with 3mm holes, and 2.5mm pins! I test fit everything with the 2.5mm pins, and see if everything works correctly, because honestly, drilling those pivots and springs out is a huge pain in the ass, especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

                      @jaya_man said:
                      I have yet to find carbide bits [emoji16]

                      Do you have Amazon where you live? There are lots of options for carbide drill bits on American Amazon

                      1 Reply Last reply
                      • jaya_man Offline
                        jaya_man
                        Global Moderators
                        Posts: 9,012
                        jaya_man Offline
                        jaya_man
                        Global Moderators
                        wrote on last edited by
                        #5 Quote Reply

                          @sLaughterMed said:
                          Honestly, I havent had any trouble with holes that were .5mm larger than the pins they rode on. Heck, Victorinox even uses the 93mm awl and pruning blade on the XAVT, with 3mm holes, and 2.5mm pins! I test fit everything with the 2.5mm pins, and see if everything works correctly, because honestly, drilling those pivots and springs out is a huge pain in the ass, especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

                          @jaya_man said:

                          I have yet to find carbide bits [emoji16]

                          Do you have Amazon where you live? There are lots of options for carbide drill bits on American Amazon

                          Have yet to have an amazon account... still searching local distributors

                          Sent from my iPhone using Tapatalk

                          1 Reply Last reply
                          • PTRSAK Offline
                            PTRSAK
                            Posts: 4,776
                            PTRSAK Offline
                            PTRSAK
                            wrote on last edited by PTRSAK
                            #6 Quote Reply

                              I have been using carbide drills like these for drilling blade/tool/spring pin holes

                              http://www.ebay.com/itm/271627790645?

                              They really need to be used in a drill press, very brittle and shatter if you try to use them in a hand drill and put any side load on them.

                              1 Reply Last reply
                              • hiraethus Offline
                                hiraethus
                                Admin Team
                                Posts: 6,969
                                hiraethus Offline
                                hiraethus
                                Admin Team
                                wrote on last edited by
                                #7 Quote Reply

                                  Good info here. :like: I'll add a link to this topic to the SAK modding guide sticky post: /topic/43303

                                  1 Reply Last reply
                                  • shibafu Offline
                                    shibafu
                                    Posts: 604
                                    shibafu Offline
                                    shibafu
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @sLaughterMed said:
                                      especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

                                      I've sometimes had a ratio closer to the other way around, 2 bits ruined for 1 hole! Drilling out a hole to a slightly larger size is hell for twist drills because all the load is on the corners of the bit and they go blunt so quickly. Solid carbide reamers are the business :) The first time I tried one, it went through the stainless steel with so little resistance that I thought I'd forgotten to tighten the chuck!

                                      1 Reply Last reply
                                      • sLaughterMed Offline
                                        sLaughterMed
                                        Posts: 3,450
                                        sLaughterMed Offline
                                        sLaughterMed
                                        wrote on last edited by
                                        #9 Quote Reply

                                          @shibafu said:

                                          @sLaughterMed said:
                                          especially with only HSS bits (expect to go through one bit per two holes, if you are lucky!)

                                          I've sometimes had a ratio closer to the other way around, 2 bits ruined for 1 hole! Drilling out a hole to a slightly larger size is hell for twist drills because all the load is on the corners of the bit and they go blunt so quickly. Solid carbide reamers are the business :) The first time I tried one, it went through the stainless steel with so little resistance that I thought I'd forgotten to tighten the chuck!

                                          Too bad carbide doesn't play nicely with hand drills

                                          1 Reply Last reply
                                          • proletenstahl Offline
                                            proletenstahl
                                            Posts: 254
                                            proletenstahl Offline
                                            proletenstahl
                                            wrote on last edited by
                                            #10 Quote Reply

                                              @Craig T said:
                                              I am preparing to mod a SAK Outrider and have been looking for the pin sizes. This is almost certainly often repeated info. I have been searching but have not found the answer.

                                              This is listed in "A "how-to" for basic SAK mods"
                                              91mm: 2.5mm outer, 2.2mm (2.25) center
                                              84mm: 2.25mm for all
                                              74mm: 2mm modern, 1.5mm older
                                              58mm: 1.5mm

                                              The 84 mm long nail file uses a 1.7 mm pin.

                                              1 Reply Last reply
                                              • LSUisSEC Offline
                                                LSUisSEC
                                                Posts: 21
                                                LSUisSEC Offline
                                                LSUisSEC
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  What pin size for the 91mm huntsman?

                                                  1 Reply Last reply
                                                  • SAKTaschenmesser Offline
                                                    SAKTaschenmesser
                                                    Posts: 198
                                                    SAKTaschenmesser Offline
                                                    SAKTaschenmesser
                                                    wrote on last edited by SAKTaschenmesser
                                                    #12 Quote Reply

                                                      @LSUisSEC said:
                                                      What pin size for the 91mm huntsman?

                                                      As original post 2.5mm and 2.2/2.25mm.

                                                      I might be wrong, but I’m under the impression that 2.2 or 2.25mm brass rod is harder to find in the USA than Europe.

                                                      Sent from my iPad using Tapatalk

                                                      1 Reply Last reply

                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                      With your input, this post could be even better 💗

                                                      Register Login

                                                      1. Home
                                                      2. Tool Talk
                                                      3. The Mod Squad
                                                      4. Pin Sizes
                                                      Reply
                                                      • Reply as topic
                                                      Log in to reply
                                                      COMMUNITY LINKS
                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                      Operational Funds

                                                      Help us keep the Unworkable working!

                                                      Make A Donation
                                                      November Goal: $300.00
                                                      Due Date: Nov 30
                                                      Total Receipts: $0.00
                                                      Below Goal: $300.00
                                                      0% funded
                                                      • Login

                                                      • Don't have an account? Register

                                                      • Login or register to search.
                                                      • First post
                                                        Last post
                                                      0