Sharpening Methods
-
Lansky system if the blades fit (the pen blades are a bit small, particularly on the fatter SAKs) to set the angle, then a Turnbox for maintenance. I keep a Vic dual sharpener handy for touching up edges too.
-
I use the Sharpmaker at 40° with the fine and sometimes ultra-fine stones (medium as necessary for a duller blade). But I'm no expert by any stretch, it's just what I can do that works. The resulting edge will slice through phone book paper with ease, that's good enough for me.
I'm no expert at sharpening, but have also been using a Spyderco Sharpmaker at 40° (on the flat side of the rods) with the fine rods, as it's the only way I've found that I can get a reasonably consistent angle and seems to avoid causing unwanted micro serrations and also doesn't scratch rest of the blade up. Metasyntax - do you find the ultra-fine rods work well and give an extra level of sharpness?
The superfine stones should make the edge smoother... and the strop will even make for much smoother cuts apart from giving the edge a mirror finish...
^^ What he said. It certainly polishes the edge more, but in my experience doesn't improve cutting performance too much. Normally, I just do the fine stones and that's it. The ultra-fine stones are just for fun.
-
I like the Victorinox sharpener pen, when on the move. At home I'm using an Arkansas whetstone or the DC4. With the latter I keep my Pioneer Solo sharp enough to shave the hairs of my arm, and it doesn't take more than a minute (it's a weekly routine). I'm not using a strop, enough is enough. No pics as my camera is malfunctioning.
-
Very old butcher steel I bought 30+ years ago at a flea market. It has been my main knife sharpening tool since I was about 13 years old.


-
I also use the Lansky guide rod system but use a coarse stone, 3 Arkansas stones (soft, hard and black hard) and then a sapphire stone for final polishing. I also use the Lansky leather strop that uses the guide rods since I'm already set up. Yellowstone compound goes on the strop. I use 25 degree (50 degree inclusive) for all of my knives so I don't have to remember which angle goes to which knife. This system puts a very fine razor edge on the knife that shaves hair easily.
For ocassional touch-up I use the Lansky Fold-A-Vee also set at the 25 degree angle. Kind of like a fold up crock stick. Don't believe they are available now but some old stock still exists and they show up on eBay at times. I found a source for someone in the UK, evidently they are very popular with soldiers over there.

-
First step. If the blade has chips, dings, or other damage, I use a pretty coarse stone made by Lansky for sharpening garden tools to remove that damage.
Step two: I have a black stone, intended for sharpening axes, and of some synthetic material (carborundum) that's pretty fine, but not as fine as my Arkansas stone to "get a good edge".
Step three: Get a sharp edge with my Smith's Soft Arkansas soapstone.
Step four: Get a shaving sharp edge by stropping with a piece of cardboard, which I lay flat.
-
For someone that is not accustomed to sharpening and/or doesn't have the patience or spare time to learn freehand (stone) sharpening, I believe that the Spyderco Sharpmaker is about the best you can get. It's simple and easy to use, works well, and works on all sorts of different blades of all lengths, and you can even use it as a makeshift bench stone if you wish. It's my favorite "system."
That said, I'm currently using freehand sharpening much more than my sharpmaker. I'm currently using a medium coarse Smiths brand diamond stone or the unglazed ring on the bottom of a ceramic coffee mug, depending on what's closer to hand. It's not that difficult once you get the hang of it, but it does take practice. What I would do is find a cheap, junky, not good for much else knife and practice, practice, practice. You'll learn pretty quick how to get a working edge on a knife. Also, don't worry too terribly much about angles. As long as it's consistent between strokes, you'll get an edge. Just don't let it be too thin or it'll chip under heavy use, and too thick will tend to be blunter than you'll want. Victorinox uses 15 degrees per side iirc, and "my angle" (the one I naturally put on all the knives I sharpen on a stone) is probably around 15 or 20, which is a good all-purpose angle for the work I do.EDIT: It's worth noting that I prefer coarser, "toothier" edges on my knives, which is why the medium diamond and coffee mug bottom work for me as primary tools. If you prefer smoother edges, you'll need more stones, and those stones will need to be finer grit to give you that smooth edge. For me, toothy edges hold up better, are easier to maintain, and cut just as well for the work I do. It's personal preference.
Hope this helps. Good luck!
-
Whetstone and some rods.
:) -
+1 for sharpmaker
-
Another sharpmaker at 40.
-
Diamond steel, pocket stones, pocket steels, pocket diamond steels, worksharp, oil stone, japanese waterstones...... and patience
-
coffee mug... the rough part of the underside xD
-
I'd like to thank y'all for your suggestions. I've continued to use the dual sharpener, and I'm pretty happy with the results, I think stropping will be my next undertaking. I've gone a little crazy with the auctions lately.... trying to cover all my MacGyver episodes... you know how it is. Really torn between the Compact, the Climber, and the Executive right now... but that's another topic.
Happy Holidays, my fellow Knights,
Keep it chivalrous.

-
For me the Victorinox dual sharpener is the best thing I bought. I just don't let my blades get too dull, a few passes regularly and its sharp enough for me

I'm a complete noob at regular sharpening, is the blade is a little dull and I try and sharpen with a stone ill make it even worse... ::)
So for me the sharpener is a lifesaver
-
I'm pretty good with whetstones, but I do use the dual sharpener most of the time because of how easy it is. It keeps my SAKs plenty sharp.
-
Just about 10 months later and my dual sharpener is still my friend... even for dull blades. I've found it's all about repetition. For blades that need more work, it's uniform strokes starting at a high number 15-25 on each side and working your way down... 20 left 20 right 15 left 15 right 10 left 10 right 5 left 5 Right 2:2 repeated 1:1 repeated... you can repeat any of them as needed... I just find with this method it's easier to find that consistent angle and I'm getting El blades as sharp as I want them.
Mags hooked me up with an awesome ceramic rod that I use for blades that just need a touch up and it does a super job. I've been finishing off with a pencil eraser but want to find a good leather strop.
Anyway, it feels good learning some basic sharpening skills, carrying a dull blade is a draaaaag.

-
If I need to touch up the edge I prefer natural stone, which manufactured by opinel, or the peace of leather with dialux paste.
If I need to sharp I prefer Japanese wetstones or if the blade looks very bad - use a diamond sharpeners. -
Sandpaper attached with binderclips in a breadboard. Pulling the spine instead of pushing. I then strop it with my tool belt if im in the province or my shoes. Never really saw the allure of sharpening system since i dont sharpen everyday.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:D SharpMaker 8)