Spirit One-Hander
-
what's the size of the pins? just out of interest.
-
@knife-man said:
what's the size of the pins? just out of interest.The pin diameter is 4mm, with the head being about 5mm.
-
@supratentorial said:
What tools did you use to remove the pin? Just a drill or did you need a mill or lathe?I used a drill press for the job. It is a several-step process:
First (while the rivet was still firmly in place) I drilled and tapped a #4-40 threaded hole right down the center of the rivet.
Next I used a 3/16" drill bit to remove the head of the rivet, by carefully "kissing" it with the spinning drill bit until it was just below flush.
The headless rivet was still stuck tight in the handle, so I had to insert a #4-40 screw into the previously threaded hole, then tap on it with a hammer until it came out the other side.
Now that I've done this for the third time, it only takes about 10 minutes. Oh, and by the way, here is a picture of the handle bracket referred to earlier. The little ledge of metal sticking out acts as a "stop" for the saw blade. It needs to be removed in order for the new knife blade to be full length.

-
No progress made on the new OH knife blade yet, but here's a picture of all the pieces. I guess I had not realized before that each one of the Spirit's handles are actually made up of four seperate pieces.
left side plate
right side plate
plier pivot bracket
individual backspring plate*(the backspring plate is riveted to the left sideplate, so they are not seperated in the picture below) *

-
Gosh, it's kind of like watching the surgery channel, only more grusome!
Def
-
Any further developments Bob?
-
The only news so far is bad news.
The entire stack of blades is engineered to precisely fit within the handle of the Spirit, and there are several different blade thicknesses in the stack. I had not noticed before that the Spirit saw blade is about half a millimeter thinner than the knife blade.So, if I proceed with my original plan of replacing the saw blade with a new one-hand blade, it will need to be somewhat thinner than the factory sheepsfoot serrated blade. (If that makes sense.)
-
@J-sews said:
The only news so far is bad news.
The entire stack of blades is engineered to precisely fit within the handle of the Spirit, and there are several different blade thicknesses in the stack. I had not noticed before that the Spirit saw blade is about half a millimeter thinner than the knife blade.So, if I proceed with my original plan of replacing the saw blade with a new one-hand blade, it will need to be somewhat thinner than the factory sheepsfoot serrated blade. (If that makes sense.)
I though you were making a blade?
-
I am! (Well, at least I plan to.)
Hmmm, maybe the post above was not clear? The dilemma is that I wish to make my new one-hand knife 2.5mm thick, same as the original Spirit blade.
But I wish to put it in the position occupied by the saw blade, which is only 2mm thick.
The matter is further complicated by those individual backsprings. Each one is cut to width precisely to match its corresponding blade. And as you can see in the photo below, the thickness varies from blade to blade.

-
@J-sews said:
....The dilemma is that I wish to make my new one-hand knife 2.5mm thick, same as the original Spirit blade.But I wish to put it in the position occupied by the saw blade, which is only 2mm thick........
Which, as it now occurs to me, explains why on the Spirit S model they replaced the scissors (also 2.5mm thick) with the spear point knife instead of the file blade or the saw.
-
I guess all this just shows how well engineered and thought out the Spirit is to have each individual implement made to different specifications.
-
-
lol

-
can you not just make the blade 2mm thick?
I don't think you will notice the .5mm performance wise
-
@knife-man said:
can you not just make the blade 2mm thick?I don't think you will notice the .5mm performance wise
I think that is my only option. Hopefully the thinner blade will not be a problem. I suppose there is only one way to find out....
-
good luck, that should work.
hope to get my first swiss tool this summer and look what i could do.
-
posting just to keep the thread alive so any new members know this is a recent project.
Hope Bob has the time to work on this, and doesnt run into too many difficulties, I know everyone is eagerly awaiting any developments.
-
i,d be very interested in seeing how this one pans out! :)
-
Thanks for the encouragement guys. I've not come up against any problems except lack of time.
(That, and my uncanny ability to start and half-finish several projects at once!)
I'll keep you posted.
-
Finally found some time this week after hours to work on a new knife blade. It's my first one ever, so I'm going really slow and being really careful. Believe it or not, every single one of those bumps and notches around the pivot on the RH end are critical. Remove too much material in the wrong place and the blade opens too far, or it doesn't lock properly, or it closes too far and wrecks the knife edge. It's definitely been a learning experience.
Next step (I think?) is too rough-in the knife edge bevel. Then it's off to heat treat, then polish up nice and shiny, then sharpen the edge properly.
This is all new to me, so if anyone has advice, please speak up!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login