Woodsmans Owners Club
-
Putting mine to work today...I really like this knife!!

-
Another pic in the sun...these Mexican special editions are gorgeous knives!

-
Another pic. If anyone wants some American Walnut for scales pm me. I have a bit!!

-
@Barry Rowland said:
Another pic. If anyone wants some American Walnut for scales pm me. I have a bit!!
In addition to the old vintage Woodsman I've accumulated four of the Mexico, two with red scales and two with ruby (like yours). The red scales are beautiful, but you're right that the ruby are outright gorgeous. A note about the last two I got (Mexico): Found that a straight pin would not stay in the hole and discovered the scales weren't completely pressed on down to the outer liners by just a hair. It was just enough to lose the friction fit for the straight pin and you wouldn't notice it without examining the knife very closely using a flashlight looking for a gap. Used a small vise with heavily padded jaws (very dense closed cell foam) and pressed them completely.
John
-
Same with this one John. It was just a fraction of a millimeter but enough that you could detect it with a light. I'll apply Operation Vice to it and we'll be in good shape.

-
@Barry Rowland said:
Same with this one John. It was just a fraction of a millimeter but enough that you could detect it with a light. I'll apply Operation Vice to it and we'll be in good shape.
Have you done this before? If not, then look at some videos (YouTube has numerous) and ensure the corkscrew is open and the T&T are out. I use very dense closed cell foam pads that are soft enough on the surface not to mar the scales. Slow application of pressure and letting it set for a while does the job . . . using a flashlight from under it to see if it has closed up. I was fooled a couple of times seeing the gap between a spring and the outer liner on the inside of it until I learned to look more carefully.
If the scales are flush to the liners the pin will have sufficient friction fit to prevent it from falling out and the friction fit of the pin is quite sensitive to that.
John
-
I haven't John, but I'll jump on Youtube. I have to make a trip to the hardware store and get some foam pads. Thanks for the heads up sir!
-
@Barry Rowland said:
I haven't John, but I'll jump on Youtube. I have to make a trip to the hardware store and get some foam pads. Thanks for the heads up sir!See how I used the vise on Day 21 in the "Discontinued challenge" thread - using the vise part near the end and note that it's a small vise. Also see how I did it during the Minimalist Challenge here, putting some scales onto a Waiter I'd modified into an Apprentice:
</post/1361428>
John
-
Been carrying the Greenwood for the last couple of days. Here it is doing what a Woodsman does best; sawing and awling:
WP_20161218_004 by magpie2112, on Flickr -
-
@FolderBeholder said:
I'd like to eventually buy a more modern Woodsman, but until then I have this approximately 1961 (thereabouts) version:That's gorgeous - I love the old style bail with cellidor scales and wish Vic had continued them.
-
I'd like to eventually buy a more modern Woodsman, but until then I have this approximately 1961 (thereabouts) version:
That's gorgeous - I love the old style bail with cellidor scales and wish Vic had continued them.
Thank you magentus, I treasure this old gal.
-
That's a real beauty FB.

-
I currently have 3 variations of the Woodsman. I don't know how many more there are.
Most likely a lot!

-
I'd like to eventually buy a more modern Woodsman, but until then I have this approximately 1961 (thereabouts) version:




[img]https://c6.staticflickr.com/1/337/30923772253_337b08fa1c_z.jpg[/imago]wThat's gorgeous - I love the old style bail with cellidor scales and wish Vic had continued them.
Really great find!
-
@JNOXID said:
I'd like to eventually buy a more modern Woodsman, but until then I have this approximately 1961 (thereabouts) version:
That's gorgeous - I love the old style bail with cellidor scales and wish Vic had continued them.
Really great find!
Thank you! It is the centerpiece of my collection at this time.
-
This is a great thread and I love a saw on anything I carry so one of these would and should be on my list of SAKs to get

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
