The Great Multitool.org Trivia Thread
-
-
question : Which multitool was destroyed by the MTO team during their last, official, visit to SHOT?
Was that the one where they pretended nothing had happened and walked off, only to be caught on camera?
No, that was a whole different event...
Def
-
What Sebertech tool was made for the drywall industry?

-
....and MTO never went to SHOT again, cursed to never be amongst the tool makers until the end of time, or until they were pardoned by the tool gods of mount Olympus
-
-
..next to the swiss banks and the swiza factory....
-
-
@Etherealicer said:
I guesstimeasure* that these SHEARS measure about 54mm from pivot to tip, which would make them the longest if they were scissors :D.Just so I know, what is your personal definition of the difference between "shears" and "scissors", 'cause it isn't very clear to me ?

I thought shears were heavier duty, designed for cutting thicker/harder materials (metal, wood etc), while scissors were more for thin/soft materials (paper, fabric, thin foil). The Wenger pictured above looks like it has what I would call scissors.
The Excalibur is what I would think of as shears:
http://wiki.multitool.org/tiki-index.php?page=Multi-Snip -
I guesstimeasure* that these SHEARS measure about 54mm from pivot to tip, which would make them the longest if they were scissors :D.
Just so I know, what is your personal definition of the difference between "shears" and "scissors", 'cause it isn't very clear to me ?

I thought shears were heavier duty, designed for cutting thicker/harder materials (metal, wood etc), while scissors were more for thin/soft materials (paper, fabric, thin foil). The Wenger pictured above looks like it has what I would call scissors.
The Excalibur is what I would think of as shears:
http://wiki.multitool.org/tiki-index.php?page=Multi-SnipYeah, there is no clear separation... I think there is a largish grey area where they are both depending on your mood. For me shears are short and stubby with more triangular blades (although that does not hold up) either. 'Cause that would make the MP600 scissors into shears.
-
don't know where to draw the line exactly, but to me:
scissors:

shears;


a matter of cutting ability and *sheer *size (pun intended)
-
-
Ok I will step up to the plate (especially with a hint like that ;) )
Sebertech Roc Wizzard
-
@THE_LONGBOW said:
Ok I will step up to the plate (especially with a hint like that ;) )Sebertech Roc Wizzard
You are correct

Next question Longbow

-
Well this is a hard question. What was LL Beans complaint about the 360 BuckTool when it first came out in 1996?
-
@THE_LONGBOW said:
Well this is a hard question. What was LL Beans complaint about the 360 BuckTool when it first came out in 1996?Helpful Hint: Buck fixed the issue when they made a version for LL Bean (and then came up with a slightly different solution for their own versions in later production runs).
-
@THE_LONGBOW said:
Well this is a hard question. What was LL Beans complaint about the 360 BuckTool when it first came out in 1996?No nail nick
-
SteveC you are correct. Buck ground approximately 1200 nail nicks into the blades on 360 BuckTools.
This is one of each version. Middle tool shows the nail nick ground into the blade.


Just curious where you found the answer.
OK SteveC your turn for a question.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






