Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

ID for a Small Screw

Scheduled Pinned Locked Moved General Tool Discussion
5 Posts 1 Posters 671 Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. ID for a Small Screw
ID for a Small Screw
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • jaw52284 Offline
    jaw52284
    Posts: 1
    jaw52284 Offline
    jaw52284
    wrote on last edited by
    Quote Reply

      I took this screw to several Home Depots to ID and they all [/img]didnt have it and said was too small to identify,

      If it helps its for a Wahl Trimmer 5537

      And Ive seen the Wahl Replacement Screws on Sally Beauty but they have been discontinued

      I lost one screw and its my brothers clipper and Im too broke to buy a new one!Thank you so much in Advance!!

      Picture 1.jpg

      Picture 2.jpg

      Picture 3.jpg

      Wahl Back**.jpg

      1 Reply Last reply
      • Grant Lamontagne Online
        Grant Lamontagne
        administrators
        Posts: 68,004
        Grant Lamontagne Online
        Grant Lamontagne
        administrators
        wrote on last edited by
        #1 Quote Reply

          Ah screws.... thou are a fickle thing....

          Your only real choices (in my opinion anyway) are as follows:

          1- Contact the manufacturer, retailer or distributor and see if they have any parts available, or suggestions on where parts may be located. This is perhaps your best bet.

          2- If option #1 fails, you can try to identify the size, pattern etc of the screw using something like THIS INFO from a place like Bolt Depot. From there, you can try contacting hardware stores, fastener distributors (Fastenal is the one I use most), eBay or other sources to see if you can find something close enough that will work. If you are lucky, you may have a knowledgeable enough guy at your local Home Depot (or equivalent) that can measure your screw for you and provide proper info for you, but this is really a bit of a desperation option and #1 is a much better bet.

          Sorry I can't be of more help, but this is a problem I have run into on a number of occasions, and it is often easier to find another solution (JB Weld or epoxy resin perhaps?) than it is to find the right screw if the manufacturer, distributor or retailer can't help you.

          Def

          EDC-TV
          SAKWiki
          GearFeed
          SAKSelector

          Merit Badges
          Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
          1 Reply Last reply
          • aldman Offline
            aldman
            Posts: 11
            aldman Offline
            aldman
            wrote on last edited by
            #2 Quote Reply

              Jezz....Fuzzy pics, but from what I see, it looks like a typical chinese "rough" tread small screw.

              I say rough because the tread it's too big to be a machined screw and to small to be a wood/metal screw. They use them all over the place and if you are like me, taking non working junk apart to fix them, you end up with a jar full of them.

              Your best bet would be to replace them. If it screws into metal, you could tap the hole for a slightly larger machined screw. If it crews into platics, taping is optional, but recommended. While you are at it, get three screws, replace both of them and keep a spare!

              The only thing you really need to be careful is: Keep the same overall lenght and be sure that the screws have blunt tips.

              Happy repairs!

              Been there, done that, got the T-Shirt and the Hat, but what I'd give to go back...

              1 Reply Last reply
              • Kampfer Offline
                Kampfer
                Posts: 7,287
                Kampfer Offline
                Kampfer
                wrote on last edited by
                #3 Quote Reply

                  For odds and ends, you will have better luck st Ace hardware

                  EDC: Black Talon, Black Cat, Spirit, LD02

                  Merit Badges
                  Photographer Hacker Mod User Airgun User Flashlight Gun User Duct Tape Reviewer LM Squirt Challenge Level 3 Off Brand MT Challenge Level 3
                  1 Reply Last reply
                  • valvestem125 Offline
                    valvestem125
                    Posts: 358
                    valvestem125 Offline
                    valvestem125
                    wrote on last edited by
                    #4 Quote Reply

                      Take the screw to a fastener supply house like K.L. Jack, and they probably can match it up.

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Tool Talk
                      3. General Tool Discussion
                      4. ID for a Small Screw
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0