Leatherman Kick Mods
-
Some info for you.
/topic/51933 -
I will have to check but I think that the Fuse is wider
All the tools should be interchangeable though
You just won't fit as much in the Kick as you can the Fuse I think 
Thanks Poncho65, that what l thought as well. The reason l went with the Kick is because l want a lightweight tool that has a pocket clip - but l would like to have a bit more room in order to have sufficient tools.
I think l have seen a few mods (on other leatherman tools) that used the hollow Kick pivot in order to use the pocket clip.
Can someone explain how this works? I assumed that the Kick pivot would be too short to use on wider tools.
Actually because of the Zytel the Kick is pretty close to the same width as the Rebar
I used a Kick pivot in my Rebar and have a clip on it right now and here is a pic 
<a href="https://flic.kr/p/PQkrGE" target="_blank" rel="noopener noreferrer"><img src="https://c3.staticflickr.com/1/669/31395753490_bb89b429d1_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>20161220_120425 by Poncho 65, on Flickr
-
I'm still waiting for my tools/parts from Loki to arrive so in the meantime l have decided on the plan for this Kick. I will replace the knife with the Blast's saw and sneak in the Blast's file on the other side. I will carry this along with a Yeoman and a mini Griptillian so scissors and a knife will be covered. There will be some room left over so l might squeeze in an awl as well, but that's stage 2.
I also just purchased a PST ii (not recieved as yet) and l was wondering if l can replace the serrated blade with the one left over from the Kick?
Also how does the width of the PST ii compare with the Kick? Would it be possible to use the pocket clip pivot pin from (another) Kick to add a pocket clip to the PST ii?
Cheers
George
-
The Kick blade may be too long but you could always shorten it to fit. I believe the Kick pivot would also be too long but you could also trim it to fit as well.
Good luck and be sure to post some pics

-
-
Thanks Guys,
So l take it that the PST's are shorter and narrower than the Kick? More compactness is always more appealing so is there any disadvantages to the PST ii over the Kick? Are the pliers smaller then?
Anyway removing material is no issue compared adding material...
I'll definitely post some pics once l've done it.
George -
I finally got my tools and parts (
Loki) and I was able to mod my Kick yesterday. Originally I had wanted to install a Blast saw, a Blast file and the Charge scissors, however I had a last minute change of heart and could go not knifeless - so I only added the saw and the scissors.It was fairly easy and I ended up only having to file off a little off the bottom of the saw and it fitted perfectly. I also had to file a little notch in the scissors tab to clear the small screw driver's length.



I'm very happy with it as it has all the commonly used tools hat I need and its lightweight and has a pocket clip (must have for me). I am totally sold on the Kicks screwdrivers - I have put up with the limitations of the short and fat Leatherman bits for too long.
I am however toying with the idea of switching the scissors out for a Rebar awl as I normally carry a mini-griptillian and a Yeoman.
Thanks for everyone's help and a BIG thank you to Loki.
Looking forward to my next build - a new Wave with SAK scissors and real drivers
-
Great pics and nice tool set

Thanks for sharing with us and I hope this MT serves you well

-
Can anyone confirm the thread size of the Kick pocket clip screw?
I think it's 5-40 UNC.
I'm thinking about drilling and tapping one of the pivots on a PST ii in order to fit a Kick pocket clip.
Cheers
George -
@george1 said:
Can anyone confirm the thread size of the Kick pocket clip screw?
I think it's 5-40 UNC.
I'm thinking about drilling and tapping one of the pivots on a PST ii in order to fit a Kick pocket clip.
Cheers
GeorgeNot sure about the size
Sorry :-\ but if you can get that to work let us know cause that would be very awesome 8) 
-
I got hold of some thread gauges and some taps and l'm calling the Kick pivot thread as 5-40 unc.
Interestingly it turns out that the PST ll pivot's are 6-32 unc.This makes it a bit harder as l know need to find a suitable stainless steel button head screw.
Anyway, the PST Ii pivot goes on the lathe this lunch time...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login