Parts for Upgrade/Repair Leatherman multitools
-
@AlphaTea said:
Hello all!
This is my first post. I am glad I found this forum, I have a Charge XTi that I want to mod.
I want to remove one of the bit holders and replace it with the scissors from a Charge TTi.
Also I need to replace my file because the diamond side a gone too smooth to work.
What tools will I need?
Thanks in advanceYou will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.
-
@loki-mobile said:
You will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.I am surmising from the previous posts here the you are "the Man" to contact about purchasing the pieces. Do you have all of these parts on hand? How are you normally paid?
I looked all over the internet trying to find a source for these parts and you are the only place I have found. And I am glad I have.I have owned Leatherman tools since about 1985 when I bought my first PST. I loved it except for trying to grab anything with the pliers hurts the hand pretty bad. I bought the Wave when it first came out and it was an order of magnitude better than the PST. I bought the XTi in 2005 and used it just about every day since. It is still in good shape but I have missed the scissors on the Wave. I probably should have bought the TTi instead.
-
You will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.
I am surmising from the previous posts here the you are "the Man" to contact about purchasing the pieces. Do you have all of these parts on hand? How are you normally paid?
I looked all over the internet trying to find a source for these parts and you are the only place I have found. And I am glad I have.I have owned Leatherman tools since about 1985 when I bought my first PST. I loved it except for trying to grab anything with the pliers hurts the hand pretty bad. I bought the Wave when it first came out and it was an order of magnitude better than the PST. I bought the XTi in 2005 and used it just about every day since. It is still in good shape but I have missed the scissors on the Wave. I probably should have bought the TTi instead.
Too bad you have the original Wave otherwise you can just swap the scissors and flat medium screw driver with the large bit driver of your XTI, and you will have a TTi...

-
I do have another Wave in storage...
How do I tell the difference between old and new Wave? -
@AlphaTea said:
I do have another Wave in storage...
How do I tell the difference between old and new Wave?The older Wave has a slimmer form factor. The new Wave is wider with bigger stronger pliers and bigger stronger knife blades and saw compared to the original slick Wave which has smaller blades/saw plus way too many flat head driver, also has an old style Phillips screwdriver instead of bits, bigger scissors and no locking mechanism for the inner implements.
-
Hello all!
This is my first post. I am glad I found this forum, I have a Charge XTi that I want to mod.
I want to remove one of the bit holders and replace it with the scissors from a Charge TTi.
Also I need to replace my file because the diamond side a gone too smooth to work.
What tools will I need?
Thanks in advanceYou will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.
Can you give me a quote for all of those items and your payment terms, please?
-
Hi!
How much would be the Leatherman bit extender?
Thanks!
-
Hello all!
This is my first post. I am glad I found this forum, I have a Charge XTi that I want to mod.
I want to remove one of the bit holders and replace it with the scissors from a Charge TTi.
Also I need to replace my file because the diamond side a gone too smooth to work.
What tools will I need?
Thanks in advanceYou will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.
Can you give me a quote for all of those items and your payment terms, please?
Write please what parts do you need?
-
Hello all!
This is my first post. I am glad I found this forum, I have a Charge XTi that I want to mod.
I want to remove one of the bit holders and replace it with the scissors from a Charge TTi.
Also I need to replace my file because the diamond side a gone too smooth to work.
What tools will I need?
Thanks in advanceYou will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.
Can you give me a quote for all of those items and your payment terms, please?
Write please what parts do you need?
I need the parts you said I would need:
disassemble tool (TT10),
wave/charge scissors,
wave/charge file,
wave/charge flat screwdriver
rebar awl, ( I'm guessing I cannot install both the awl and screwdriver, I will decide which to install after I see them)
2 washers
Thanks in advance -
[quote author=AlphaTea link=topic=64314.msg1428501#msg1428501 date=1487440280]
Hello all!
This is my first post. I am glad I found this forum, I have a Charge XTi that I want to mod.
I want to remove one of the bit holders and replace it with the scissors from a Charge TTi.
Also I need to replace my file because the diamond side a gone too smooth to work.
What tools will I need?
Thanks in advanceYou will need bits for disassemble tool (TT10), wave/charge scissors, wave/charge file, wave/charge flat screwdriver or rebar awl, washer. Large bit holder thickness in more than twice the standard tool.
Can you give me a quote for all of those items and your payment terms, please?
Write please what parts do you need?
I need the parts you said I would need:
disassemble tool (TT10),
wave/charge scissors,
wave/charge file,
wave/charge flat screwdriver
rebar awl, ( I'm guessing I cannot install both the awl and screwdriver, I will decide which to install after I see them)
2 washers
Thanks in advance
[/quote]Reply to PM
-
Write please what parts do you need?
[/quote]
I need the parts you said I would need:
disassemble tool (TT10),
wave/charge scissors,
wave/charge file,
wave/charge flat screwdriver
rebar awl, ( I'm guessing I cannot install both the awl and screwdriver, I will decide which to install after I see them)
2 washers
Thanks in advance
[/quote]Reply to PM
[/quote]
Reply and payment sent
-
Hiya.
Would one of the bit holders fit my Crunch?
Thanks!
Chris
-
@ChrisinHove said:
Would one of the bit holders fit my Crunch?What's wrong with the standard 1/4" hex bit driver already in your Crunch ? (take out the tension adjusting screw and you'll see it) ???
-
Would one of the bit holders fit my Crunch?
What's wrong with the standard 1/4" hex bit driver already in your Crunch ? (take out the tension adjusting screw and you'll see it) ???
It's more a case of swapping out what I don't need - the blade - for something more useful to me. I was hoping to be able to fit a bit that would take 1/4 drive sockets.
-
Would one of the bit holders fit my Crunch?
What's wrong with the standard 1/4" hex bit driver already in your Crunch ? (take out the tension adjusting screw and you'll see it) ???
It's more a case of swapping out what I don't need - the blade - for something more useful to me. ** I was hoping to be able to fit a bit that would take 1/4 drive sockets.**
You mean like the SOG one that fits diagonally into 1/4" square female sockets ?
https://www.sogknives.com/1-4-driver.html
/topic/39195All the bit holders I've seen are much thicker than the Crunch blade, so even if the tang fits (or can be made to fit) you would have to sacrifice other tool components to make room.
/post/601722There are adaptors that will do that for your Crunch: 1/4" hex male to 1/4" square male
-
You're right. I'm trying to reinvent the wheel, aren't I!
-
Hi,
I would like to order 2 X LM wrenches please.
-
I would like to order a set of 2 lite wrenches if you still sell them. Thanks.

-
@JustinCase said:
I would like to order a set of 2 lite wrenches if you still sell them. Thanks.

I replied to to your pm and payment sent for Set#10 (Two (2) lite Leatherman wrenches) - $19 with shipping

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login