The Hacked Leatherman Owners Club.
-
Always love my clipped Rebar

20170304_151134 by Poncho 65, on Flickr -
This is my first LM mod... not as cool and awesome as all the other hacks I've seen in this forum... it's just a simple S30V blade swap for my Wave....


Sent from my iPhone using Tapatalk
-
Nice!
-
Thanks DTT...
Before that, I was inspired to make a DIY ratchet based on a youtube video... I made mine in such a way that I can use it on my Wave, Skeletool CX, Juice KF4, Vic Spirit and SAKS. Haven't tried it out on the CX but since it has the same sized bits as the Wave, I'm thinking there should be no problem...





I guess I can call it my own universal ratchet system...
Sent from my iPhone using Tapatalk
-
Nice job on that universal ratchet.
-
Before that, I was inspired to make a DIY ratchet based on a youtube video... I made mine in such a way that I can use it on my Wave, Skeletool CX, Juice KF4, Vic Spirit and SAKS. Haven't tried it out on the CX but since it has the same sized bits as the Wave, I'm thinking there should be no problem...
I guess I can call it my own universal ratchet system...
Good job Jaya_man
Could you share the video that inspired you? Or... more details on the one you did?
-
Some very good modding jaya 8)

-
Thanks DTT, SurivStud and Poncho

This is the video that inspired me...
I cut down a cheap ratchet I had laying around

Cut down the ratchet handle (what used to be) to length... stuck in a 1/4 12mm socket and epoxyed them together... adjusted the square hole of the ratchet (stuck in a small piece of license plate) so that all my tools can fit.



Sent from my iPhone using Tapatalk
-
Thanks jaya_man
[emoji736]
-
-
20170315_180333 by Poncho 65, on Flickr
20170315_180230 by Poncho 65, on Flickr -
@Poncho65 said:
20170315_180333 by Poncho 65, on Flickr
20170315_180230 by Poncho 65, on FlickrNice old hacked beauty ;)
-
Thanks Troels

-
20170317_154542 by Poncho 65, on Flickr -
Thanks guys

-
Hello all, first time/long time here, and I am determined to be a member of this club! I have a Charge Tti, (also Surge and Crunch) and I just picked up a Rebar for a smokin' deal at Canadian Tire ($27-in store clearance do to discontinuation, SCORE!) and I am going to make my Charge a ReCharge! Now, I had been planning on sending in the Charge for warranty, I bought it used and there is some looseness in the large bit driver, the retention clip is a little bent. I was bouncing back and forth though, because other than that it's pretty good. It's from '13, and it's been used, small chip around the tip of the PE among other minor things. ANYWAY I want to learn to sharpen my blades and I decided just before I left for the post office that I would swap the bit holder from my Surge and go ahead with the mod today. My dad is bringing by his Dremel in a half hour and I'm going to use the method that leaves the scissors intact, and I'll take a little material off of the one "jowel". HOWEVER upon loosening the pin screw for the inside tools on the large bit side (after heating) something unanticipated happened; the scale began to bend out as though pressure was being applied to it from the inside, I'm guessing the liner lock for the PE. I haven't seen any documentation of the exact procedure used for taking out inner tools on a Charge tti, and I assumed it was a simple procedure, the Surge, having no scales was easy. Does anyone have any tips for keeping the scale from bending out when removing inner tools? I'm thinking maybe clamp the scales so they stay in place while loosening the pin. Any advice appreciated, I don't want to break my beloved Charge on my first mod attempt

-
Welcome to the forum duF

I don't have a Charge so this may not work but maybe you'll have to loosen the plier side as well to equalize the pressure on the scale.
-
Welcome to
DuFunk 
I don't have a Charge either so I really can't comment on this :-\ Good luck with the modding though and that was also a great deal on the Rebar

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login