What did you use your Leatherman for today?
-
-
Used my well ussd ST300 as an example of what multitool to buy/ look for to a new believer.
-
Used my well ussd ST300 as an example of what multitool to buy/ look for to a new believer.
What a good use.
+1
It always helps to have a well used LM to show people how good they last and how well they do

-
Today my little girl wanted to drive her bike. I was wearing trousers and didn't want something bulky on my pockets so I took the Juice S2. A few minutes later, I realized that she was ready to change her training wheels to a higher position.
Juices are great for those cases where you can't carry a large MT. We must apply criteria in order to know if this compact device will be adequate for the task but they are stronger than what their size seems to project.

-
All in one cooking utensil





-
I disassembled a Wave to help with disassembling a first production run Charge Ti, and another FPR Wave. Both of the FPR tools have problems: Charge with broken plier stopping tab, Wave with broken scissor tab. I did not want to send both in. Thinking that LM likely give me an AL to replace the Ti, I moved the broken scissors from the Wave to the Charge. I used the female screw from the first Wave to help with aligning the screw thru the handle and pliers. It worked like a charm. I may consider selling parts of the first Wave, and keep the screws as tools.
On another note, LM had tighter tolerance and better fit and finish on these FPR tools. It took me a good while to disassemble them. Also, paying a little more for quality bits paid off. I got the 5-star bits made by Wera from Micro-Tools. The fit was perfect. I did not heat up the locktite, just muscled it thru. The bits held up well, without rounding off, while the screws came off undamaged. Pretty good German quality stuffs.
-
Turned my Wave into an impromptu door wedge while working in an elevator shaft today.
-
@chrono said:
I disassembled a Wave to help with disassembling a first production run Charge Ti, and another FPR Wave. Both of the FPR tools have problems: Charge with broken plier stopping tab, Wave with broken scissor tab. I did not want to send both in. Thinking that LM likely give me an AL to replace the Ti, I moved the broken scissors from the Wave to the Charge. I used the female screw from the first Wave to help with aligning the screw thru the handle and pliers. It worked like a charm. I may consider selling parts of the first Wave, and keep the screws as tools.On another note, LM had tighter tolerance and better fit and finish on these FPR tools. It took me a good while to disassemble them. Also, paying a little more for quality bits paid off. I got the 5-star bits made by Wera from Micro-Tools. The fit was perfect. I did not heat up the locktite, just muscled it thru. The bits held up well, without rounding off, while the screws came off undamaged. Pretty good German quality stuffs.
Did you happen to get any pics of the disassembly
I would have love to have seen some in between and after shots

-
@surfdaworld said:
Turned my Wave into an impromptu door wedge while working in an elevator shaft today.
Bet that use isn't listed on the LM website :D Very creative use buddy

-
New page banana man dance

-
dishwasher was on the blink - sorted it, but needed to cut the drain pipe for the waste hose, used my wave saw for the job, worked nicely, especially as i couldn't have got in with a hacksaw space was too cramped :)
didn't take any pics, was too busy cutting/fixing :) -
Used the Skeletool to retrieve a screw in a 2 ft. hole.

-
ST200 helped yesterday get my grill clean and ready for the season
</post/1455164>
-
Using my mod Rebar I repaired satellite few days ago. Easy job because it was here on Earth, not in the outer space as usual ;)

-
@IvanDrago said:
Using my mod Rebar I repaired satellite few days ago. Easy job because it was here on Earth, not in the outer space as usual ;)

:o

-
@IvanDrago said:
Using my mod Rebar I repaired satellite few days ago. Easy job because it was here on Earth, not in the outer space as usual ;)

Awesome!

-
Used the S30V blade to open my Utili-Key 👍

-
Used the serrated blade on my OG Supertool to cut off and old Plastic pot so I could transplant an Arborvitae in a new pot.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

