And so it begins.... (My adventures into Alox!)
-
Nice, yet all I see is pocket lint..
JR -
Here was todays work. The skeletonized scales end up weighing almost exactly the same as plastic... but will outlast the human race since not much reacts with Ti. :D



I don't see pocket lint :D but I do have an idea with the skeletonized scales
Be cool to have a spot on there by the main blade to have a wire stripper hole perhaps 
-
:D :D

Here was todays work. The skeletonized scales end up weighing almost exactly the same as plastic... but will outlast the human race since not much reacts with Ti. :D



I don't see pocket lint :D but I do have an idea with the skeletonized scales
Be cool to have a spot on there by the main blade to have a wire stripper hole perhaps 
Don't have a wire close by... just used the toothpick as ilustration... notch on combo tool could be used together with the blade to strip wire


Sent from my iPhone using Tapatalk
-
You're right jaya
That is a good idea when the 2 of them are side by side like that 
-
EDC'ers react in the presence of Ti, but thats different right?
Looks
worthy as usual. 
-
@Pablo O'Brien said:
EDC'ers react in the presence of Ti, but thats different right?
Looks
worthy as usual. 
Yes! It sends our hearts all a flutter 
-
Here is the closest to a swiss champ ive done so far. Just missing the all important fish scaler. :D





-
And a new Challenge project to have a brass inlaid fish bone emblem based on a picture of a cuff link provided by the customer.

I machined half way through the scale to make the pockets.

And then cut some brass pieces to fit.

And then eased them on in and sanded flush. It's going into the tumbler next.



-
@Syph007 said:
And a new Challenge project to have a brass inlaid fish bone emblem based on a picture provided by the customer.
I machined half way through the scale to make the pockets.

And then cut some brass pieces to fit.

And then eased them on in and sanded flush. It's going into the tumbler next.



Now that's impressive.

-
That almost Swisschamp is awesome Syph
and that inlay is awesome stuff buddy :o

-
Oh sick!

JR -
-
And a new Challenge project to have a brass inlaid fish bone emblem based on a picture provided by the customer.

I machined half way through the scale to make the pockets.

And then cut some brass pieces to fit.

And then eased them on in and sanded flush. It's going into the tumbler next.



Now that's impressive.

No doubt about it +1 to this

-
Staggering work Syph

-
Ok I'm back. The inlay is...... gotta lay down again.
A... Maze..... Ing......
-
-
@Fast Bill said:
And a new Challenge project to have a brass inlaid fish bone emblem based on a picture provided by the customer.

I machined half way through the scale to make the pockets.

And then cut some brass pieces to fit.

And then eased them on in and sanded flush. It's going into the tumbler next.



Now that's impressive.

No doubt about it +1 to this

+2

Sent from my iPhone using Tapatalk
-
The inlays look great!

Also, you should do a xlt, just to show it is possible... ::)
-
Excellent work as always

Sent from my SM-G920R4 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
