Gerber Center Drive question
-
Hello all.
I'm new to the forums but have been doing a lot of reading posts trying to decide on my next EDC multi tool.I currently have a SOG Power Assist that has been working fine for over 3 years. My reason for looking for a new tool is that I wanted a better screwdriver / philips experience. I did some research and was looking at both the Leatherman Surge and the Gerber Center Drive.
I picked up the drive last week to give it a go and while I like it, I have had some issues with the cutters. I tried to cut a Cat6 ethernet cable and to my surprise, the Gerber couldn't cut it. It took multiple tries to just get it to cut the cable and when it was finished, the cable was in pretty bad shape. I had other people try it and I tried different cables and every single time, it just didn't work.
Are these cutters not built for this type of work or do I have a defective Center Drive? I really like this tool but being that there are no other cutters on here like scissors, I may need to return this and go with the Surge.
Thanks for the help.
-
Welcome to
jesse
I don't have a Center Drive so can't help you with this question but maybe someone that has one can answer your questions

-
Welcome to the boards jesse.
Like Poncho I don't have a CD but I have tested some similar plier cutters over here. -
I have a CD but do not have any CATx cable with me. When I am at the shop tomorrow I will check my CD on some cable. Hopefully this will not disqualify me on my MP600 challenge as I will still have my MP600 with me.
-
I think you'll get away with it. ;) :)
-
Gerber's carbide cutters are not very good. They'll cut soft wire forever, but anything hard and they tend to shatter. I know from experience. Not too sure regarding cat5, though
I've emailed Gerber several times suggesting they keep the indexable cutter idea, but use a resilient metal like 154cm in place of carbide. No reply

-
Welcome to the forum!
I have a Center-Drive but no CAT-5 cable to test it on, although I have cut other wire with it and had no problems.
How is it they are not cutting? Are they binding or gnawing? Is the cable resisting them entirely?
I would check to see if the cutters are lining up flush with each other both with and without cable in them to see if they are misaligned. If they are binding up when you are cutting and the cutters seem aligned then it might be a problem with a loose plier head, which would absolutely be a warranty issue.
Def
-
I seem to recall having trouble cutting Cat5 cable with the bypass cutters on a multitool but I just tried it with a LM Juice, SOG PPP, Vic Spirit, and LM Crunch and it worked fine in one cut. I can even cut it with a SOG CrossGrip and LM Squirt but it sometimes requires two bites because the length of cutting edge is so small. Don't have a Center Drive but I surmise Grant is right and the cutters aren't flush.
-
Wow.
Thanks for all the responses. The cutters look aligned to me. I'll attach some pics so everyone can get the idea. Too bad this MT doesn't have any scissors. I'm really missing those right now. -
That is bizarre indeed. I am not sure why that is happening? They should be plenty sharp enough to cut it. Have you tried taking two bites at it? They seem like the wire is getting flattened and almost cut, but the stuff protruding front and back may be causing resistance?
Are the cutters themselves sharp? Or are they defective? Can you see any burrs, chips, cracks etc in them that might be keeping them from cutting all the way through?
I am going to dispense with asking what happens if you really bare down on them, since I am going to assume that, like all technicians I know, you have probably crushed it with everything you have and sworn at it a few times.
And yes, I agree completely about the scissors. I think all multitools need to come with scissors, especially Gerbers, because they are owned by Fiskars, and they make some some excellent scissors.
Def
-

I just tried Vic 91mm scissors on Cat5 cable and while it does work I'm not sure I would want to use them for that purpose on a regular basis.
I think I would return that Center Drive.
-
Got a chance to use my CD on some CAT5e. No pix as it was a quick check, but it cut fine. Make sure the screws that hold the blades on are tight. I went to cut something with my MP600 and it wouldn't cut properly. I thought someing had happened to the cutters and was going to turn them to a new side. When I went to loosen the screws, they were already loose! So I tightened them up and it cut fine.
-
Be careful tightening them up, though. Too tight and they could shatter (happened to a coworker)
-
I checked them and they were tight. I removed them and rotated them any ways and I'm getting the same result. I ordered the Leatherman Surge and will test that out on Monday.
I'll let everyone know how that worked out.
-
Better order the SwissTool Spirit as well...

-
Well the Leatherman arrive and it cut the Cat5 cable without issue. Those scissors are pretty heavy duty. I ordered the black oxide one. Any tips on how to best wipe off the excess oxide coating? It's rubbing off every time I handle it.
I got the nylon pouch which I like as it has some extra space for accessories or a flash light. I'm no 100% sure what I'm going to do yet. I honestly really like the Center Drive. I'm not a big fan of the Leatherman 2D bits or the bit extender. Someone I work with has them and I played around with them a bit. While they work, they just don't feel as nice as the standard bits do. Also, I didn't realize that while standard bits fit into the bit extender, they go down too far because it's made for the double sided 2D bits. Not to mention the bit kit and extender will run me around $45 so it's an extra cost where the Gerber came with the bits and its already extended.
This past weekend, I needed to do some light work at home and I needed an extension for a philips drive. I just pulled out my other bit kit, popped in a philips extension onto the center drive and it worked like a charm.
Like I said, I'm torn. I have until May 14th to decided if I'm going with the Leatherman Surge or the Gerber Center drive. That's my last return date.
-
The 2D bits are fine, but of course depends from the stuff you do with them. Nothing beats real bits thats for sure. I have always been torn between my Leatherman Wave and Gerber MP1 too, like you are with Surge and CD. Let us know what you decide.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




