Vintage SAK Owners Club
-
@JNOXID said:
It is not rare knife just early 1960s Angler 235 faU, but it looks like in 1960s this one is not so common as Fisherman with Phillips instead of corckscrew.
Sent from my iPad using Tapatalk



Excellent pic!

-
1.3703 Hoffritz

-


I take it your a classic DE safety user?
JR -



I take it your a classic DE safety user?
JRWhen I bother shaving these days..... yes. My preference is the old Gillette razors, favorite being the fatboy.

-



I take it your a classic DE safety user?
JRWhen I bother shaving these days..... yes. My preference is the old Gillette razors, favorite being the fatboy.

Ditto when, mine is a Merkur,
JR -
Finally finished my collection of 84mm metal file SAKs with the addition of a small Mountaineer (top right). Has issues with over-sharpening of the blades but as my dear old mom used to say, "beggars can't be choosers". It will be a good place holder until (or is that "if") a better example comes along. It is from the 70's.
The others are the small Grand Prix (top left), also from the 70's, small Master Craftsman (bottom left) from the 70's and small Master Craftsman (bottom right) from the 60's.


-
@Boonies said:
Finally finished my collection of 84mm metal file SAKs with the addition of a small Mountaineer (top right). Has issues with over-sharpening of the blades but as my dear old mom used to say, "beggars can't be choosers". It will be a good place holder until (or is that "if") a better example comes along. It is from the 70's.The others are the small Grand Prix (top left), also from the 70's, small Master Craftsman (bottom left) from the 70's and small Master Craftsman (bottom right) from the 60's.

Really nice collection! Congrats!
Now you need 1950s Master Craftsman small and 1980s Grand Prix small



-
@JNOXID said:
Finally finished my collection of 84mm metal file SAKs with the addition of a small Mountaineer (top right). Has issues with over-sharpening of the blades but as my dear old mom used to say, "beggars can't be choosers". It will be a good place holder until (or is that "if") a better example comes along. It is from the 70's.
The others are the small Grand Prix (top left), also from the 70's, small Master Craftsman (bottom left) from the 70's and small Master Craftsman (bottom right) from the 60's.

Really nice collection! Congrats!
Now you need 1950s Master Craftsman small and 1980s Grand Prix small

I knew I wasn't finished!! 😛 My oh my, that 1950's MC is yummy. Always liked that old style awl. Very, very nice.

My small Grand Prix could be (probably is) from the 1980's, late 1970's to early 1980's at least. A backup would be good though, so I'll keep looking. 😜

-
@JNOXID said:
Finally finished my collection of 84mm metal file SAKs with the addition of a small Mountaineer (top right). Has issues with over-sharpening of the blades but as my dear old mom used to say, "beggars can't be choosers". It will be a good place holder until (or is that "if") a better example comes along. It is from the 70's.
The others are the small Grand Prix (top left), also from the 70's, small Master Craftsman (bottom left) from the 70's and small Master Craftsman (bottom right) from the 60's.

Really nice collection! Congrats!
Now you need 1950s Master Craftsman small and 1980s Grand Prix small

Very nice. Afraid to touch my "Spartan " it's at least 70 yoa.....and I used it as a beater as a kid. OMG (she is safe now)
-
I'm a big fan of the vintage look and I'm planning a mod that will hopefully have a little of the best of old and new but I got stuck a little on the bail.
How big are the "heads" of the bail (where the rivet goes through) and what's the diameter of the rod? With all these nice vintage SAKs around maybe someone could be so kind as to measure for me?
-
Hi F2
I made a bail for an old British/Indian Army Knife last weekend
I am hoping to post a mod guide on this sometime - I took the photos etc etcBriefly - The bail pin/rivet diameter for my BAK is the same size as a SAK - 2.5mm
And the bail itself is going to be about 2.5mm - So as you say .....
Challenge: How do I get the pin through the brass of the same thickness ???
My solution: …. was to get some 3.2mm brass rod - Then thin the middle section to 2.5, then flatten the ends so that they are wide enough to have a 2.5mm hole drilled through them, then bend to make the bail!!
Simples !! .......... Not
-
I made a bail for an old British/Indian Army Knife last weekend
I am hoping to post a mod guide on this sometime - I took the photos etc etcBriefly - The bail pin/rivet diameter for my BAK is the same size as a SAK - 2.5mm
And the bail itself is going to be about 2.5mm - So as you say .....
Challenge: How do I get the pin through the brass of the same thickness ???
My solution: …. was to get some 3.2mm brass rod - Then thin the middle section to 2.5, then flatten the ends so that they are wide enough to have a 2.5mm hole drilled through them, then bend to make the bail!!
Simples !! .......... Not
That's basically the same way I'm doing it except I started with a 4 mm rod. Rigging the rod up in a drill press to use as a lathe. Right now I have a four millimeter sphere at one end that I intend to flatten once the second is done. It just felt like 4 mm would look a bit small but it's hard to say until I'm closer to finishing it.
-
- Great minds think alike

Yep I made a 'lathe' too - 'cept I don't have a press - So had to clamp the hand drill then use that
I am pretty sure it was 3.2mm. The thinning took for ever >:(
I was also worried it would be too thin for the attachment point - but it worked fine
One important tip:
Heat the brass before you flatten it. My first attempt failed, as the brass split on the flattening after several hits - When heated it was fine.***EDIT: ***Here is how it turned out - I was pretty happy
More to be revealed later !!
- Great minds think alike
-
@Huntsman said:
8) Great minds think alike
Yep I made a 'lathe' too - 'cept I don't have a press - So had to clamp the hand drill then use that
I am pretty sure it was 3.2mm. The thinning took for ever >:(
I was also worried it would be too thin for the attachment point - but it worked fine
One important tip:
Heat the brass before you flatten it. My first attempt failed, as the brass split on the flattening after several hits - When heated it was fine.***EDIT: ***Here is how it turned out - I was pretty happy
More to be revealed later !!Hmm, then it seems like our approaches were less similar than I thought, here's how I've been working. I have the second "head" left but I'm getting there. My approach will require another step where I plan on flattening the bulbs against a sander before drilling.
-
Elinox 1137U and 1237U from 1960s-early 1970s. Not very common Phillips screwdriver without file. Who knows when they changed the ELINOX stamp from big to small size?

-
I believe it coincides with the change in the other stamp with at 74.
-
- Great minds think alike

Yep I made a 'lathe' too - 'cept I don't have a press - So had to clamp the hand drill then use that
I am pretty sure it was 3.2mm. The thinning took for ever >:(
I was also worried it would be too thin for the attachment point - but it worked fine
One important tip:
Heat the brass before you flatten it. My first attempt failed, as the brass split on the flattening after several hits - When heated it was fine.***EDIT: ***Here is how it turned out - I was pretty happy
More to be revealed later !!Hmm, then it seems like our approaches were less similar than I thought, here's how I've been working. I have the second "head" left but I'm getting there. My approach will require another step where I plan on flattening the bulbs against a sander before drilling.
Wouldn't it be easier to just cut a piece of brass rod, bend it in half and then bend the two extremities and insert them in the knife?...

- Great minds think alike
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

.jpg)