Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Strong but small pliers?

Scheduled Pinned Locked Moved General Tool Discussion
31 Posts 1 Posters 2.6k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Strong but small pliers?
Strong but small pliers?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • zoidberg Offline
    zoidberg
    Posts: 38,161
    zoidberg Offline
    zoidberg
    wrote on last edited by
    #6 Quote Reply

      :think:

      1 Reply Last reply
      • Vidar Offline
        Vidar
        Posts: 2,605
        Vidar Offline
        Vidar
        wrote on last edited by Vidar
        #7 Quote Reply

          The drill part will be just fine - ask a workshop to do it for you. Most likely they will make the hole with a screw inside to minimize initial thread damage, and then clean up the thread afterwards with a tap. As for the leverage a hole wrench provides plenty - it is their sole purpose for existing.

          But of course, a plier can be used for so many other things too :)

          My personal favorite when all other pliers fail, various Knipex included, is the old Kongsberg 92 design pipe wrenches:
          http://www.hitachi-powertools.no/mediabank/store/2244/61050702---Rortang_print.jpg

          The hardened jaws will bite straight into steel nuts if necessary to make grip were there were none.

          That part of yours look like an adapter for photography stuff - those tend to get real stuck.

          Come to think of it you might want to look at small locking welding pliers too; the small are cute sized but will still has plenty of grip.

          "Simple is hard"
          "Hard is hard too"
          (Partial disclosure: I design tools for a living).

          Merit Badges
          MTo Anniversary Challenge
          1 Reply Last reply
          • rivercity Offline
            rivercity
            Posts: 498
            rivercity Offline
            rivercity
            wrote on last edited by
            #8 Quote Reply

              @zoidberg said:
              Could you file a little flat bit on each side for the PS to grip?

              This is what Im thinking as well, file or mill flats 180 deg apart, then a small crescent wrench would work just fine. :cheers:

              Chuck

              "Well, when it comes down to me against a situation, I don't like the situation to win." ~ MacGyver

              Merit Badges
              Mod User Flashlight Hacker Time Lord Level 1 Paracord Hook User Duct Tape EDCSource Buyer Discontinued SAK/MT Challenge Scale Changer Fire Making EDC Pocket Dump Challenge Birth Year SAK Titanium Ignore Carabiner User Modified SAK Challenge
              1 Reply Last reply
              • chx Offline
                chx
                Posts: 21
                chx Offline
                chx
                wrote on last edited by
                #9 Quote Reply

                  @Vidar said:
                  The drill part will be just fine - ask a workshop to do it for you.

                  Pardon for me being an idiot but what's a workshop in this context and where would I find one :)

                  Google is https://www.google.ca/search?q=vancouver+workshop&rlz=1C1CHBF_en-GBCA742CA742&oq=vancouver+workshop&aqs=chrome..69i57j0l5.4002j0j1&sourceid=chrome&ie=UTF-8 no help.

                  I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                  1 Reply Last reply
                  • Amedio Offline
                    Amedio
                    Posts: 23
                    Amedio Offline
                    Amedio
                    wrote on last edited by
                    #10 Quote Reply

                      If you have enough room around it, Pocketwrench II will do a good job.

                      1 Reply Last reply
                      • theonew Offline
                        theonew
                        Posts: 1,294
                        theonew Offline
                        theonew
                        wrote on last edited by
                        #11 Quote Reply

                          The SOG CrossGrip might work. It has thicker pliers and the pliers section is more rounded, which might allow for more contact area and a better grip. Also it has compound leverage which adds a bit of grip. It isn't the most comfortable to bear down on but with a glove on or even a bandana you can exert a surprising amount of force for its size. They are discontinued but can often be found on Ebay for $20 - $30. It does have a knife blade but that can be easily removed.

                          404 Not Found

                          favicon

                          (www.multitool.org)

                          1 Reply Last reply
                          • chx Offline
                            chx
                            Posts: 21
                            chx Offline
                            chx
                            wrote on last edited by chx
                            #12 Quote Reply

                              @Amedio said:
                              If you have enough room around it, Pocketwrench II will do a good job.

                              :like: confiscate that! And at 17mm tops it's just big enough. And yes, there is a ton of space around it.

                              I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                              1 Reply Last reply
                              • dbnyc Offline
                                dbnyc
                                Posts: 51
                                dbnyc Offline
                                dbnyc
                                wrote on last edited by
                                #13 Quote Reply

                                  What about a small strap wrench?

                                  1 Reply Last reply
                                  • Vidar Offline
                                    Vidar
                                    Posts: 2,605
                                    Vidar Offline
                                    Vidar
                                    wrote on last edited by
                                    #14 Quote Reply

                                      Ah, I thought you needed access from the side as it might be was stuck in both ends.

                                      A workshop in a hole making setting would be a place with a minimum of mechanical tools. A hole is not difficult. Any place with a drill press, a V block and a tap could make it to perfection, and most could make a good hole even without all those. (IE pretty much any place involved with making or repairing any physical items or equipment). Two flats as also suggested would also work for sure - I was just thinking a single hole would be easier to make.

                                      But it seems you found a good portable solution already :)

                                      "Simple is hard"
                                      "Hard is hard too"
                                      (Partial disclosure: I design tools for a living).

                                      Merit Badges
                                      MTo Anniversary Challenge
                                      1 Reply Last reply
                                      • Vidar Offline
                                        Vidar
                                        Posts: 2,605
                                        Vidar Offline
                                        Vidar
                                        wrote on last edited by Vidar
                                        #15 Quote Reply

                                          Ok, I'm bored today, and since this is a multi-tool forum I thought a more bespoke solution might be interesting for a change. Hence, a 16mm grip wrench - I added in a 3/8" and 1/4" hex while I was at it, and did little a picker gripper thing at the end. It just so happens to be sized similar to a Victorinox (91x23,8mm). And finally Grant get something with more than one tool that doesn't have a cap opener! Blasphemy! :D

                                          (If you actually want to cut it PM me for the files - a laser cutting shop (many online) should do it quite quickly. 3-4mm steel or titanium should do fine, aluminium likely not so good as it has to spring a bit).

                                          16mm round wrench1.jpg

                                          16mm round wrench2.jpg

                                          16mm round wrench3.jpg

                                          "Simple is hard"
                                          "Hard is hard too"
                                          (Partial disclosure: I design tools for a living).

                                          Merit Badges
                                          MTo Anniversary Challenge
                                          1 Reply Last reply
                                          • chx Offline
                                            chx
                                            Posts: 21
                                            chx Offline
                                            chx
                                            wrote on last edited by chx
                                            #16 Quote Reply

                                              @Vidar said:
                                              Ah, I thought you needed access from the side as it might be was stuck in both ends.

                                              No, the 3/8" end never gets stuck the 1/4" end always and so hard that much stronger people than me couldn't get it out with the Style PS alone. For sheer craziness: It gets stuck in a keyboard which I use vertically :D See https://geekhack.org/index.php?topic=79810.0 this topic, the quick release plate in the first post has been replaced by this screw and when I move from place A to place B I need to tear down the whole thing so it can be packed in a small place :)

                                              I will ask Vidar for his files and see whether https://www.sculpteo.com/en/lasercutting/laser-cutting-materials/stainless-steel-material/ or http://lasergist.com/discover/ could cut it for me :D

                                              I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                                              1 Reply Last reply
                                              • Vidar Offline
                                                Vidar
                                                Posts: 2,605
                                                Vidar Offline
                                                Vidar
                                                wrote on last edited by
                                                #17 Quote Reply

                                                  Laser cutting does introduce a tiny bit of taper along the edges, but I put in a tiny bit of tolerance for that. The hole is a tiny bit oversize as the gripper should close down on it anyway. If adjustments to spring stiffness or size does need to be made a round file is your friend :)

                                                  "Simple is hard"
                                                  "Hard is hard too"
                                                  (Partial disclosure: I design tools for a living).

                                                  Merit Badges
                                                  MTo Anniversary Challenge
                                                  1 Reply Last reply
                                                  • gregozedobe Offline
                                                    gregozedobe
                                                    Posts: 5,148
                                                    gregozedobe Offline
                                                    gregozedobe
                                                    wrote on last edited by
                                                    #18 Quote Reply

                                                      I'd be inclined to look for something like this (or get a tool made with similar functionality):

                                                      https://circuitousroot.com/artifice/fitting/mechanics/tools/pin-wrench/index.html (scroll down to # 490)

                                                      That looks so innocuous I don't think even the most officious official would want to confiscate it from you. You would have to machine/file a groove into the fitting to give it somewhere to grip (and remember to backcut a little to allow the "tooth" to grip properly under tension rather than slip out).

                                                      babola: "Enjoy your tools and don't be afraid to air your opinion and feelings here, but do it in courteous and respectable way toward others, of course."

                                                      1 Reply Last reply
                                                      • Etherealicer Offline
                                                        Etherealicer
                                                        Admin Team
                                                        Posts: 12,034
                                                        Etherealicer Offline
                                                        Etherealicer
                                                        Admin Team
                                                        wrote on last edited by
                                                        #19 Quote Reply

                                                          Would a Pocketwrench II work?

                                                          It wouldn't be the internet without people complaining.

                                                          1 Reply Last reply
                                                          • chx Offline
                                                            chx
                                                            Posts: 21
                                                            chx Offline
                                                            chx
                                                            wrote on last edited by
                                                            #20 Quote Reply

                                                              @Etherealicer said:
                                                              Would a Pocketwrench II work?

                                                              Yes, see #10 and #12 I already ordered one :)

                                                              I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                                                              1 Reply Last reply
                                                              • chx Offline
                                                                chx
                                                                Posts: 21
                                                                chx Offline
                                                                chx
                                                                wrote on last edited by
                                                                #21 Quote Reply

                                                                  @dbnyc said:
                                                                  What about a small strap wrench?

                                                                  Do they even make strap wrenches with four inch or smaller handles?

                                                                  I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                                                                  1 Reply Last reply
                                                                  • chx Offline
                                                                    chx
                                                                    Posts: 21
                                                                    chx Offline
                                                                    chx
                                                                    wrote on last edited by
                                                                    #22 Quote Reply

                                                                      @zoidberg said:
                                                                      Swiss+Tech ST50022

                                                                      Sorry but no, that has practically zero grip in this situation. I just tested it :)

                                                                      I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                                                                      1 Reply Last reply
                                                                      • zoidberg Offline
                                                                        zoidberg
                                                                        Posts: 38,161
                                                                        zoidberg Offline
                                                                        zoidberg
                                                                        wrote on last edited by
                                                                        #23 Quote Reply

                                                                          @chx said:

                                                                          @zoidberg said:

                                                                          Swiss+Tech ST50022

                                                                          Sorry but no, that has practically zero grip in this situation. I just tested it :)

                                                                          1 Reply Last reply
                                                                          • chx Offline
                                                                            chx
                                                                            Posts: 21
                                                                            chx Offline
                                                                            chx
                                                                            wrote on last edited by chx
                                                                            #24 Quote Reply

                                                                              I want to report that the strap wrench won. Although not as small as some other tools (the one I found is 6 inches long and some 2 inches wide at the head) since it's all plastic it's not heavy at all and works very well. It also helps opening stuck lids in the kitchen :D It's "Performance Tool W54059 2-Piece Strap Wrench Set" , I gave the normal sized away. Since I do not have a car before this thread I never heard of these things :)

                                                                              Security at YVR and YLW airport didn't care (does it even show up? I have NFI) while the previous tools were always scrutinized before let through.

                                                                              The Pocketwrench II also works but I needed to figure out it needs to be flipped to loosen the nut vs tightening.

                                                                              I have an eBay search warning me when an SOC Crossgrip comes up for sale, eventually I will get one but for now I am set.

                                                                              I work from home but fly too much. When I carry things it involves an airplane and the TSA. Makes for different considerations.

                                                                              1 Reply Last reply
                                                                              • gregozedobe Offline
                                                                                gregozedobe
                                                                                Posts: 5,148
                                                                                gregozedobe Offline
                                                                                gregozedobe
                                                                                wrote on last edited by
                                                                                #25 Quote Reply

                                                                                  @chx said:
                                                                                  I have an eBay search warning me when an SOC Crossgrip comes up for sale, eventually I will get one but for now I am set.

                                                                                  You could ask the seller (Chrysta) of this CrossGrip if she is willing to post to Canada. I've bought several tools from her in th epast and she has been quite helpful (but I do have a US address)

                                                                                  Invalid URL

                                                                                  favicon

                                                                                  (www.ebay.com)

                                                                                  babola: "Enjoy your tools and don't be afraid to air your opinion and feelings here, but do it in courteous and respectable way toward others, of course."

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. General Tool Discussion
                                                                                  4. Strong but small pliers?
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0