Kayak repair
-
@JP said:
Good work Grant! Closed cell foam is great stuff. If you have any left over you could pad the cockpit for comfort and control.Sent from my XT1563 using Tapatalk
That's my plan. Megan's boat is fairly comfortable as it is a lot newer but most of the foam on the seat of mine is worn away and on long trips I get a welt going on my lower back from where the seat rubs so I think I got enough to take care of that as well.
My boat is in pretty sad shape, while the one Megan uses gets most of the attention!
Def
-
I can't begin to imagine what it would cost to have that work done. Nice for you to take on that project, but mostly getting the boat in shape.
-
@Grant Lamontagne said:
Yeah, riveting the handles wasn't a big deal, but the rigging for the rudder was a bit involved. Pretty straightfoward if you know what you are doing, but if you've never done it before it seems a bit overly complex.Now I see why everything is done the way it is and it makes perfect sense.
I hope you are still billing for the whole shift.... >:D
Def
We did shift back a gear or 2

And the client agreed for 2 full days of work beforehand so... -
@Aloha007 said:
I can't begin to imagine what it would cost to have that work done. Nice for you to take on that project, but mostly getting the boat in shape.If I had to guess, I'd say probably around $45/hour and a three hour minimum, plus materials and taxes, so I'd probably be into the whole thing for a couple of hundred dollars at least.
As it was, I think the rivets (special kayak rivets ::) ) cost around $7 for a bag of 20-ish, the replacement handles cost somewhere around $16 each and the cable cost somewhere around $1.50/foot and I bought about 30 feet because I thought I'd have to replace the hard lines too.
Boat parts is a good racket to be in for sure....
Def
-
Its times like these that can also make you a buck or two. You now have parts and experience. I'm sure theres someone who has the same issues you have and would be stoked to save a but on repairs. When I cycled I accumulated parts and experiene and made a buck from time to time. Many times just enough to break even from parts but it was still not bad since my bike was fixed free ( minus my time ).
-
@Grant Lamontagne said:
I can't begin to imagine what it would cost to have that work done. Nice for you to take on that project, but mostly getting the boat in shape.
If I had to guess, I'd say probably around $45/hour and a three hour minimum, plus materials and taxes, so I'd probably be into the whole thing for a couple of hundred dollars at least.
As it was, I think the rivets (special kayak rivets ::) ) cost around $7 for a bag of 20-ish, the replacement handles cost somewhere around $16 each and the cable cost somewhere around $1.50/foot and I bought about 30 feet because I thought I'd have to replace the hard lines too.
Boat parts is a good racket to be in for sure....
Def
Check out The Chandlery for boating eye candy.
I dream of building a SUP.
-
I keep meaning to get there. So far I've been to MEC, Cabelas, Sail and Jenda.
Def
-
All in all I probably have a couple of hours into the repair,
I believe home repairs are usually measured in beers, not hours.
Changing oil and filter is a one-beer job.
Belts and water pump? Four beers.
anything with fibreglass? scotch.
Boat parts is a good racket to be in for sure....
:D
Bring
Out
Another
Thou....If you think parts for your kayak are expensive.

:ahhh :o
-
Perhaps it's me but I have had issues raising and lowering the rudder on nearly every kayak I have hired... I believe the mechanism could be designed better.
-
Good work there Grant !

-
@Syncop8r said:
Perhaps it's me but I have had issues raising and lowering the rudder on nearly every kayak I have hired... I believe the mechanism could be designed better.Funny you should say that.....
I have been working on designing a rudder assembly to fit my big boat.
I'm also still waiting for the foam to arrive, so I'm glad I didn't take the pedals off in anticipation.

Def
-
Sweet Composites is also a good source. It is out of MD in the US.
Sent from my XT1563 using Tapatalk
-
I have been there three times this week already- I can't wait for the Princess Auto to open up next door! :ahhh
As if Cabelas didn't already cost enough, one of my next great weakness stores is going in right next door!
Def
-
@Grant Lamontagne said:
I have been there three times this week already- I can't wait for the Princess Auto to open up next door! :ahhhAs if Cabelas didn't already cost enough, one of my next great weakness stores is going in right next door!
Def
Ha, didn't know you are a fan of PA. I'm glad there isn't one in QC (or Lee Valley for that matter), saved me buying a lot of crap I won't use.
-
I think MEC should put a store out here. It would do well due to the Cabela's draw and it's offerings would complement Cabela's.
Sent from my XT1563 using Tapatalk
-
For pedal screws, after bolstering the rack as you mentioned, I would place small rubber grommet between screw head and body of kayak. A good brushing off/ graphite application of the pedal rack is great help.
I have an older Wilderness Systems and Islander, simpler kayaks, but I have run them roughshod. I use cut up strips of an old frisbee and a heat gun at 1100 Fahrenheit to patch cracks and small holes. Then I file it down. Not always pretty, but one of my repairs has yet to fail.
-
Thanks for the advice- I haven't heard any complaints yet this year about water leakage, so I am guessing I got it done properly. :D
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




