Mora Club
-
For me it was between the Companion and Classic #1 since I have only those two. Easy decision in that regards.
Another point of discussion this could bring up is the general popularity of scandi ground blades. It is no secret I admire the LT Wright Genesis as a grail, but oddly enough I'm leaning more towards the full flat ground version than the scandi. Only huge caveat here is the way we use knives, i.e. are there more woodcrafting tasks or are the tasks very widespread and since all grinds can accomplish the same tasks with various degrees of difficulty, how much of an impact can tasks that rely more on brute force (like batoning) have in the choices of grinds.
Sure it is hard to picture Mora Classic being pushed into such a task, especially since most people will have a hatchet, axe or large knife. However it does get tricker when going with a minimal tool loadout since the big tasks aren't foreseen as a huge need.
To bring you closer to my current mindset you can take a little thought experiment:
You're hiking from point A to point B in a familiar ecosystem. You can have what you can carry on your back, belt and pockets. The hike is organized in such a way that it allows for a comfortable pace, stops to have a drink, get some food (fishing, small game hunting and/or what you brought with you) and set up a shelter that you are hiking with (again your preferred system) but you'll still be on the move for 5 days. What is your tool load out and is every gram of that equipment really necessary? If you want to make things more complicated, you can restrict yourself with a weight limit too. :D :D :D -
@styx said:
For me it was between the Companion and Classic #1 since I have only those two. Easy decision in that regards.Another point of discussion this could bring up is the general popularity of scandi ground blades. It is no secret I admire the LT Wright Genesis as a grail, but oddly enough I'm leaning more towards the full flat ground version than the scandi. Only huge caveat here is the way we use knives, i.e. are there more woodcrafting tasks or are the tasks very widespread and since all grinds can accomplish the same tasks with various degrees of difficulty, how much of an impact can tasks that rely more on brute force (like batoning) have in the choices of grinds.
Sure it is hard to picture Mora Classic being pushed into such a task, especially since most people will have a hatchet, axe or large knife. However it does get tricker when going with a minimal tool loadout since the big tasks aren't foreseen as a huge need.
To bring you closer to my current mindset you can take a little thought experiment:
You're hiking from point A to point B in a familiar ecosystem. You can have what you can carry on your back, belt and pockets. The hike is organized in such a way that it allows for a comfortable pace, stops to have a drink, get some food (fishing, small game hunting and/or what you brought with you) and set up a shelter that you are hiking with (again your preferred system) but you'll still be on the move for 5 days. What is your tool load out and is every gram of that equipment really necessary? If you want to make things more complicated, you can restrict yourself with a weight limit too. :D :D :DI have thought about this often and sometimes do. If I am going out to set up a base camp, then scout from there, I am a tad more tool heavy. Knife, saw and hawk. Then when I got out from the camp, I have very little. Backpacking or day long hikes, not so tool heavy. I can get buy easily with just Mora Bushcraft Black. I actually rarely baton even if I just have my knife. When I do, rarely anything above 2 inches for fire prep or say, carving a spoon. Most of the time I can get a fire without feather sticks. Good to keep practice though.
I find it interesting that you are thinking full flat. Nothing wrong at all with that mind you. But I have never much cared for them. I seems like I could never master them. A hollow grind, no problem. But I am pretty sure that is because I grew up with hollow grind hunting knives. Scandi grind for some reason just works for me. First time I used one, it just spoke to me. -
Ok. I think I got it.
I can imagine the knife will become a better slicer if you round off the shoulders. But like Ducttapetech said, you might sacrefice some fine control, then again you might not. It might just be different and need a little practice to regain the fine control.
Question is, will you notice the difference on such a thin blade as a classic no1?Looking forward to see the result.

-
For me it was between the Companion and Classic #1 since I have only those two. Easy decision in that regards.
Another point of discussion this could bring up is the general popularity of scandi ground blades. It is no secret I admire the LT Wright Genesis as a grail, but oddly enough I'm leaning more towards the full flat ground version than the scandi. Only huge caveat here is the way we use knives, i.e. are there more woodcrafting tasks or are the tasks very widespread and since all grinds can accomplish the same tasks with various degrees of difficulty, how much of an impact can tasks that rely more on brute force (like batoning) have in the choices of grinds.
Sure it is hard to picture Mora Classic being pushed into such a task, especially since most people will have a hatchet, axe or large knife. However it does get tricker when going with a minimal tool loadout since the big tasks aren't foreseen as a huge need.
To bring you closer to my current mindset you can take a little thought experiment:
You're hiking from point A to point B in a familiar ecosystem. You can have what you can carry on your back, belt and pockets. The hike is organized in such a way that it allows for a comfortable pace, stops to have a drink, get some food (fishing, small game hunting and/or what you brought with you) and set up a shelter that you are hiking with (again your preferred system) but you'll still be on the move for 5 days. What is your tool load out and is every gram of that equipment really necessary? If you want to make things more complicated, you can restrict yourself with a weight limit too. :D :D :DI have thought about this often and sometimes do. If I am going out to set up a base camp, then scout from there, I am a tad more tool heavy. Knife, saw and hawk. Then when I got out from the camp, I have very little. Backpacking or day long hikes, not so tool heavy. I can get buy easily with just Mora Bushcraft Black. I actually rarely baton even if I just have my knife. When I do, rarely anything above 2 inches for fire prep or say, carving a spoon. Most of the time I can get a fire without feather sticks. Good to keep practice though.
I find it interesting that you are thinking full flat. Nothing wrong at all with that mind you. But I have never much cared for them. I seems like I could never master them. A hollow grind, no problem. But I am pretty sure that is because I grew up with hollow grind hunting knives. Scandi grind for some reason just works for me. First time I used one, it just spoke to me.The one knife to solve everything.
Isnt that why we accumulate knives? The search for that amazing knife that will do everything? :DIf you are batoning a lot the convex grind is better than the scandi, no doubt.
In my limited experience, convex ground knives are what I call "quick and dirty" knives. They eat wood in big chunks and can take a beating, but can be a bit of a pain for finer stuff. But that might just be because I grew up with scandis and have been using them all my life.Id probably bring a scandi and a light hatchet.
-
I am not 100% if I want to find the knife that can do everything. I mean, once you found it, what would be the point of living after that? Sure we still have beer... :D
-
@ducttapetech said:
I am not 100% if I want to find the knife that can do everything. I mean, once you found it, what would be the point of living after that? Sure we still have beer... :D
but beer is nice 
-
I am not 100% if I want to find the knife that can do everything. I mean, once you found it, what would be the point of living after that? Sure we still have beer... :D
but beer is nice 
True dat!
Cheers gentlemen!
-
No beer so I'll hit the Rum with little Gaute


-
@Grathr said:
Ok. I think I got it.
I can imagine the knife will become a better slicer if you round off the shoulders. But like Ducttapetech said, you might sacrefice some fine control, then again you might not. It might just be different and need a little practice to regain the fine control.
Question is, will you notice the difference on such a thin blade as a classic no1?Looking forward to see the result.

I might notice it on one thing - carrots. For me they are the best indicator of wedging. Also maybe on cross grain cuts on wood.
For me it was between the Companion and Classic #1 since I have only those two. Easy decision in that regards.
Another point of discussion this could bring up is the general popularity of scandi ground blades. It is no secret I admire the LT Wright Genesis as a grail, but oddly enough I'm leaning more towards the full flat ground version than the scandi. Only huge caveat here is the way we use knives, i.e. are there more woodcrafting tasks or are the tasks very widespread and since all grinds can accomplish the same tasks with various degrees of difficulty, how much of an impact can tasks that rely more on brute force (like batoning) have in the choices of grinds.
Sure it is hard to picture Mora Classic being pushed into such a task, especially since most people will have a hatchet, axe or large knife. However it does get tricker when going with a minimal tool loadout since the big tasks aren't foreseen as a huge need.
To bring you closer to my current mindset you can take a little thought experiment:
You're hiking from point A to point B in a familiar ecosystem. You can have what you can carry on your back, belt and pockets. The hike is organized in such a way that it allows for a comfortable pace, stops to have a drink, get some food (fishing, small game hunting and/or what you brought with you) and set up a shelter that you are hiking with (again your preferred system) but you'll still be on the move for 5 days. What is your tool load out and is every gram of that equipment really necessary? If you want to make things more complicated, you can restrict yourself with a weight limit too. :D :D :DI have thought about this often and sometimes do. If I am going out to set up a base camp, then scout from there, I am a tad more tool heavy. Knife, saw and hawk. Then when I got out from the camp, I have very little. Backpacking or day long hikes, not so tool heavy. I can get buy easily with just Mora Bushcraft Black. I actually rarely baton even if I just have my knife. When I do, rarely anything above 2 inches for fire prep or say, carving a spoon. Most of the time I can get a fire without feather sticks. Good to keep practice though.
I find it interesting that you are thinking full flat. Nothing wrong at all with that mind you. But I have never much cared for them. I seems like I could never master them. A hollow grind, no problem. But I am pretty sure that is because I grew up with hollow grind hunting knives. Scandi grind for some reason just works for me. First time I used one, it just spoke to me.The one knife to solve everything.
Isnt that why we accumulate knives? The search for that amazing knife that will do everything? :DIf you are batoning a lot the convex grind is better than the scandi, no doubt.
In my limited experience, convex ground knives are what I call "quick and dirty" knives. They eat wood in big chunks and can take a beating, but can be a bit of a pain for finer stuff. But that might just be because I grew up with scandis and have been using them all my life.Id probably bring a scandi and a light hatchet.
Actually it is more about my obsession with getting the most out of everything. If I'm lifting in running shoes, I'm leaving kilograms out there in the ether. If I'm drinking for the sake of drinking and going with beer, I'm leaving promilles out there in the ether. If I'm relying on a tool for a specific niche and not giving it the environment for optimal performance, I'm doing that tool a disservice as any lackluster part of its performance is user error. At least that is my take on it.
@ducttapetech said:
I am not 100% if I want to find the knife that can do everything. I mean, once you found it, what would be the point of living after that? Sure we still have beer... :DI'm more of a whiskey man. And finding a knife that can do everything has been done. Look at any knife with a somewhat decent edge and chances are that you can do everything you need to with it, given some thought as to how to achieve that. But finding a knife that can live in a backpack because it can take on lighter woodcrafting chores, spread peanut butter, gut fish, do food prep and not get messed up by quick and dirty "touch ups" is the current goal.
Would I say that is the best knife for everything? Hell no. Can't open a can, a bottle of beer and certainly won't survive those "hold my beer and watch this" moments. There are a lot better knives for that application out there. Cold Steel SRK springs to mind oddly fast
-
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


-
@theonew said:
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well

Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 

-
Yikes, that pic cut my eyeball just looking at it :ahhh
-
Nice work you two!
-
@theonew said:
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well

I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 
Glad to see you 2 are getting good results
-
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 
Glad to see you 2 are getting good results
There pretty easy to sharpen ,although little Gaute took some work as had been well loved before :D
-
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 
Glad to see you 2 are getting good results
There pretty easy to sharpen ,although little Gaute took some work as had been well loved before :D
Nice work, both of you!

-
I gave my wife a Mora 2000 to keep in her car (along with a SAK Huntsman and SAK Rescue Tool). I'm considering a Kansbol,
so I wanted to look at the profile grind of the Mora 2000 as it is similar to Kansbol. My wife has used it for a few odds and ends tasks but I was blown away by how sharp it still was.It had a slightly rolled tip so I ran it over my Sharpmaker ceramic rods just to "freshen" it up. After just a little maintenance, her Mora 2000 is about as sharp as anything I own! I have a handful of 2.5mm Moras, but none with the profile grind as on the 2000 and Kansbol. Wow! Is the profile grind that much easier to make razor sharp?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


