Mora Club
-
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 
Glad to see you 2 are getting good results
There pretty easy to sharpen ,although little Gaute took some work as had been well loved before :D
Nice work, both of you!

-
I gave my wife a Mora 2000 to keep in her car (along with a SAK Huntsman and SAK Rescue Tool). I'm considering a Kansbol,
so I wanted to look at the profile grind of the Mora 2000 as it is similar to Kansbol. My wife has used it for a few odds and ends tasks but I was blown away by how sharp it still was.It had a slightly rolled tip so I ran it over my Sharpmaker ceramic rods just to "freshen" it up. After just a little maintenance, her Mora 2000 is about as sharp as anything I own! I have a handful of 2.5mm Moras, but none with the profile grind as on the 2000 and Kansbol. Wow! Is the profile grind that much easier to make razor sharp?
-
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 
Glad to see you 2 are getting good results
Indeed.
Very tempted to give this a go as well, but I might have to pick up a new Mora to try it on. 
-
I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


I knocked the shoulder off of my carbon clipper and also sharpen it on three angles which makes it convex and I can attest that it makes a rather noticeable difference in the wedging department. This is our kitchen utility knife and I use it a lot on cardboard and plastic and rounding the shoulders definitely increases the performance. Also I might add this knife really holds an edge well. It gets beaten like a rented mule and even when it becomes dull it will still cut fairly well


Nice job mate
this is how little Gaute turned out and it cuts really well ,although I do like a convex grind but usually on bigger chopping type knives 
Glad to see you 2 are getting good results
Indeed.
Very tempted to give this a go as well, but I might have to pick up a new Mora to try it on. 
Join us. I'll start my experiment tomorrow
uuuu very nice gear choices
-
OK, I've started knocking off the shoulder on my Classic No1. I'll be honest and say that it's not a Mora I ever particularly pick up, especially since I bought a No2/0. I even remembered to take a "before" pic. :D
-
good thinking with the before pic
-
Here is a good funny video including a trip to the mora factory with Dutch bushcraft knives
-
well I am late with the experiment since some things popped up (if you really want to hear my annoyed rants just ask). but here is step #1 - softening the shoulders. knocking the shoulders off entirely is somewhat impossible without moving the knife to a zero grind
before
IMG_20170725_083116after
IMG_20170725_084249As you can see it does look a bit more convexed. In a practical sense I've managed to stab myself while making something jambalaya like (pics of food when it is done). The wedging issue is already much better and slicing ability has improved on soft materials like very ripe tomatoes (that's how I stabbed myself)
-

How does it perform on wood? -
As mentioned earlier I got myself a No2 in sweeden a couple of weeks ago.
I desided to modifie it a bit. I squared the spine, sanded the handle, burned it and oiled it and gave the blade a patina.I also stumbeled upon the leather sheath online. According the seller, it is a Mora sheath. Looks like it originally was for a fishing knife, but fits the No2 nicely. (And I only paid $2,50 for it :D Too bad he only had one, or I would have bought a bunch to share with you)
I oiled the sheath as well.Im not sure I improved it. In retrospect I think the red handle would have looked better. Also, if drop it, I sure wont find it!





-
Nice Gaute! Nice work on the knife.
-
@ducttapetech said:
Nice Gaute! Nice work on the knife.Thanks!

-
Very nice Gaute
love that sheath as well nice find and bargain price 
-
The board I tested it on gave the following results:
Scandi - average cut depth was 5mm
1st modification - average cut depth was 8mmThe problem is that I snapped the board and threw it away before taking pictures. Since the first cut depth was so low, we can safely say it was a rather hard wood.
Nice job on the modifications
-


How does it perform on wood?The board I tested it on gave the following results:
Scandi - average cut depth was 5mm
1st modification - average cut depth was 8mmThe problem is that I snapped the board and threw it away before taking pictures. Since the first cut depth was so low, we can safely say it was a rather hard wood.
Nice job on the modifications
Cool. Thanks for the info. Also, nice work.
-
@styx said:
well I am late with the experiment since some things popped up (if you really want to hear my annoyed rants just ask). but here is step #1 - softening the shoulders. knocking the shoulders off entirely is somewhat impossible without moving the knife to a zero grindbefore
IMG_20170725_083116after
IMG_20170725_084249As you can see it does look a bit more convexed. In a practical sense I've managed to stab myself while making something jambalaya like (pics of food when it is done). The wedging issue is already much better and slicing ability has improved on soft materials like very ripe tomatoes (that's how I stabbed myself)
Nice. That's exactly what I've done and I've come to the same conclusions as well. I have managed to avoid stabbing myself though.

-
well i'm somewhat clumsy, or perhaps better said careless enough to have a few mishaps. I think with time it will perform even better although the question that can now be asked is the edge stability compromised
-
Here's the best pic I could manage last night. I think there is more I could do but it's a good enough start.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


