Your thoughts/ideas please
-
hmmm.....
If you change any of the ramps, would the tools lock after removing metal? I my mind they would be a little loose. -
-
@hiraethus said:
I modified the tang on the saw when I did mine:

Didn't take much off at all in order to make it lock.Cool! Nice work! So no play at all?
-
I think there was some, but I decided it wasn't an issue. The lock wasn't coming undone, and a bit of play in the saw didn't affect how it worked.
-
@hiraethus said:
I think there was some, but I decided it wasn't an issue. The lock wasn't coming undone, and a bit of play in the saw didn't affect how it worked.
works for me! -
Cheers Chris

-
BTW did you put a cut out to access the nail nick on the end or not?
-
@hiraethus said:
I modified the tang on the saw when I did mine:

Didn't take much off at all in order to make it lock.Did similar when I was adding OHO scissors to a Charge. Did it to the file. No problems, just take a little bit and test each time.
-
@50ft-trad said:
BTW did you put a cut out to access the nail nick on the end or not?No, I think the action was smooth enough that I was able to OHO it using my thumb.
-
Ah, yes - when you swap the saw over to the other side, the detent nub on the lock tab doesn't have anything to engage with, so it's easier to open the saw.
-
Aw crap!

I just noticed that I'll have to do the saw AND file, as the scissors have to go in one of their slots too ::)
-
Why Two pairs of scissors or are you going to switch out the smaller ones for something ?
-
@SteveC said:
Why Two pairs of scissors or are you going to switch out the smaller ones for something ?Yeah, the internals were done before I had figured out what I was going to do with the external configuration.
The external scissors aren't behaving at the moment in terms of correctly locking open and tensioning the spring. Once I've got that fixed, I'll be completely reprofiling the scissor blades to make them more usable. The design of the Wingman scissors are abysmal, and I'll be moving the cutting edges more inline with the pivot, similar to what Zoidie has done on his, and possibly refining the pivot and crinking them a little better. Until the edges are where they should be so that they cut instead of just pushing material away, I won't know what other refinements are needed.
Once all the externals have been finished, I'll be looking at replacing the internal scissors. I don't know what with yet, as it all depends what I've got in the parts tub. I may end up repurposing the package opener from the Wingman, or maybe looking at making an awl out of something.
-
Sounds like a plan Al . I'd go for an awl myself.

-
Well all the externals are in position, and all open and close. I've done a little reprofiling on the scissors, but they still need fine tuning. They do now look an improvement over the originals.
An awl may well be the logical choice, Steve. Looks like I've gut fewer LM parts in the tub than I thought. :-\ There's what looks like a BO Rebar driver in there, so that's a potential candidate.



-
@ducttapetech said:
hmmm.....
If you change any of the ramps, would the tools lock after removing metal? I my mind they would be a little loose.That was my fear too before Chris mentioned his. The saw locks up quite solidly, and there's just a tiny wiggle on the file, but nothing detrimental

-
@50ft-trad said:
hmmm.....
If you change any of the ramps, would the tools lock after removing metal? I my mind they would be a little loose.That was my fear too before Chris mentioned his. The saw locks up quite solidly, and there's just a tiny wiggle on the file, but nothing detrimental

Sounds good to me brother. If two of you says it good, then it's works for me. It not like you guys would lead me a stray. Right? Right?!

-
@50ft-trad said:
hmmm.....
If you change any of the ramps, would the tools lock after removing metal? I my mind they would be a little loose.That was my fear too before Chris mentioned his. The saw locks up quite solidly, and there's just a tiny wiggle on the file, but nothing detrimental

Sounds good to me brother. If two of you says it good, then it's works for me. It not like you guys would lead me a stray. Right? Right?!

Not unless we were there to film the hilarious consequences >:D :D :D
-
Nice job !
I used a medium driver to do my Pulse awl and it worked well

DSC00294 2_zpsdj9ssxey by SteveC, on Flickr
DSC00301 2_zpscmz03klb by SteveC, on Flickr
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

