Learning to make Sheaths
-
Wow great setups Chako and JR thanks for showing them.
Is the inside of the wallet done JR I'm thinking about making one soon maybe, but without card slots. I'd be interested to see how it turns out.
Super idea for the workstation. :)Chako I like your rivet setter set, :) mine are all separate bases :(
-
@sak60 said:
Wow great setups Chako and JR thanks for showing them.Is the inside of the wallet done JR I'm thinking about making one soon maybe, but without card slots. I'd be interested to see how it turns out.
Super idea for the workstation. :)Chako I like your rivet setter set, :) mine are all separate bases :(
No, as you can see its not stitched all the way around.
JR -
Wow! I'm not even going to say what I have for leather working. You'd all be ROFLMAOSHMSFOAIDMT...

Here's a little close-up of my Pattada folder pouch. It's a couple of years old and the leather is getting a beautiful worn, shinny look. I might redo the stitching, adding a couple of holes on both ends, to make it more resistant.


-
I like it pfr

Pattada's are a cool pattern too

-
@pfrsantos said:
Wow! I'm not even going to say what I have for leather working. You'd all be ROFLMAOSHMSFOAIDMT...

Here's a little close-up of my Pattada folder pouch. It's a couple of years old and the leather is getting a beautiful worn, shinny look. I might redo the stitching, adding a couple of holes on both ends, to make it more resistant.
Well, instead of just telling others how to do it the right way, while my own stitching wasn't, I got off my lazy bum (well, to tell the truth it was the other way around, I sat on my lazy bum) and redid the stitching on my Pattada pouch. Added a couple of holes at the ends, so as to keep the edge of the smaller half secured against the other.
Note to self (and others): when stitching, don't skimp on the thread. I tried to be "frugal" and ended up having to cut the new stitching and redo it again. I didn't have a long enough thread the first time. I got some 5x the stitching length next and it was enough. Better have some spare thread thrown away than having to start again...

Final result. You can compare with the older pics. I also started at hole #3, went to the first, retraced the stitching and did the same at the end.




-

Nice job pfr
Since I started doing leather stitching I've wondered whether there is a ratio to use for the right thread length and I have always erred on the side of being too long so have had a lot of wastage. -
Taken from one of my resources...
"To determine correct length of thread, pull two lengths off spool...equal to your arms' length (both arms spread wide open). This will be bout 8' to 10' in total length. Do this with each thread you prepare. Do not cut thread length to fit any particular project. Make them all of about the same length. Instructions explain joining thread, using short ends, etc...if more thread is required".
Yeah, there will always be a little wastage. If the length is long enough, I keep it for a smaller project down the road.
-

Is that in one of the books you posted, if so which one please? -
@Chako said:
Taken from one of my resources..."To determine correct length of thread, pull two lengths off spool...equal to your arms' length (both arms spread wide open). This will be bout 8' to 10' in total length. Do this with each thread you prepare. Do not cut thread length to fit any particular project. Make them all of about the same length. Instructions explain joining thread, using short ends, etc...if more thread is required".
**
Yeah, there will always be a little wastage. If the length is long enough, I keep it for a smaller project down the road.**This, too. I've used some small pieces of thread for my keychains. Thread is also dirt cheap, you can afford to waste some now and again.


-
Good idea :)
-
Yes, in the hand sewing book with red cover.
-
I had to go to the store to buy more AAA batteries. Now that I have done this, I can now install the under-shelf lighting. These little Velcroed units give off a good amount of LED lighting, as each unit comes with 3 swivel lights and 2 power settings.
Here is the desk with all 3 lights installed.
<a href="http://s145.photobucket.com/user/Chako_photo/media/Chako_photo005/IMG_4300small_zpsnhdrsbrw.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i145.photobucket.com/albums/r207/Chako_photo/Chako_photo005/IMG_4300small_zpsnhdrsbrw.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>Almost done the move.

-
Wow chako, looking good!!
JR -
I have one of these Aus WW2 knives coming so this is the next sheath I will be doing minus the hanger because i don't have one.
Also a couple of pouch mods because I don't like Velcro so replaced with snaps. -
This is the start of the Australian Commando Knife sheath.
No leatherwork space at present :( so doing it wherever I can.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
