Plierench the Ultimate Collector's Multitool
-
@skou said:
OK, found another use for the newer models.
(Anything with straight cut gear teeth,)Install the LONG jaw, the one that goes in
both ways. You can use it for compressing
wheel calipers, when doing a brake job.One heck of a lot quicker, than the C-clamp.
OK my Plierenches are NOT on display,
but in my tools, and used.steve
Wow!
What a great use. I will definitely give this a try. Thanks for sharing.
-
Gentleman and Ladies and the rest of you guys, I give you what I consider to be the Holy Grail of plierenches. The Eifel Geared-Pivot 1000% Plierench...and its mine!
-
Saw you won it. 8)
Glad you now have it in hand!
Congrulations!!! 
-
hi, just found this site. I recently got one of these tools at a Restore for $1 its 7 1/2" long has price stamped in it of $4.50 no date and 2 Pat numbers 1181654 , 1882817 and jaws have V notch in both. wire cutter slot, screw driver on end of 1 handle what year was mine made? its in very good cond just a bit of rust on surface that cleans off easy. what do the numbers mean 7"-45-10_8 to1
Thanks! Mitch
-
@Mitch Garstang said:
My latest acquisition. 1949 Plierench with modified jaws. I'm not sure how this one was used. It appears to be made for piercing tubing?
likely for putting a tap on refrigerator lines to connect guage hose to. as many such tools where made for the field.
I could see that.
-
I saw a lot of 2 8 1/2s that were selling for the price of one ($20 shipped) on Ebay that was ending in an hour, so I bought them. One's going to need some work to the spring, the other's been whacked on. I'll likely keep one for myself, then give my granddad the other. Got any advice on how to fix the messed up spring?

-
@cody6268 said:
I saw a lot of 2 8 1/2s that were selling for the price of one ($20 shipped) on Ebay that was ending in an hour, so I bought them. One's going to need some work to the spring, the other's been whacked on. I'll likely keep one for myself, then give my granddad the other. Got any advice on how to fix the messed up spring?
One of the many uses for plierenches is emergency hammer.

I may have a diagram on how the spring is configured. I'll check and get back to you in a few days.
-
@Mitch Garstang said:
hi, just found this site. I recently got one of these tools at a Restore for $1 its 7 1/2" long has price stamped in it of $4.50 no date and 2 Pat numbers 1181654 , 1882817 and jaws have V notch in both. wire cutter slot, screw driver on end of 1 handle what year was mine made? its in very good cond just a bit of rust on surface that cleans off easy. what do the numbers mean 7"-45-10_8 to1Thanks! Mitch
Mitch, these (7"-45-10_8 to1) numbers mean;
7" (7 inches.) 43-10 October of 45. 8 to 1, is
the ratio of movement. 1/8 movement would
be 1 inch at the end of the handles. The 8.5
model is 10 to 1.steve
-
OK, just saw an Ebay sale that had an 8.5, and a 7
inch, with 9 jaws, (wire, pipe cutter, another wire,
large pipe, reverse, 2 small pipe, and 2 regular jaws.
Also had the clamp fixture, as well as the pipe cutter
V piece.)$65 at Ebay. (Well, it WAS at Ebay. Now on its way
to MY humble abode.)Couldn't pass it up!
My question; will all the jaws fit in either Plierench?
(I've never had the 7 inch, in fact, never even SEEN
one.)steve
-
@skou said:
OK, just saw an Ebay sale that had an 8.5, and a 7
inch, with 9 jaws, (wire, pipe cutter, another wire,
large pipe, reverse, 2 small pipe, and 2 regular jaws.
Also had the clamp fixture, as well as the pipe cutter
V piece.)$65 at Ebay. (Well, it WAS at Ebay. Now on its way
to MY humble abode.)Couldn't pass it up!
My question; will all the jaws fit in either Plierench?
(I've never had the 7 inch, in fact, never even SEEN
one.)steve
Nice buy! If I'm not mistaken they may be a matched set. They were both made in 1949. I'm not sure if the months match.
The larger jaws generally don't fit the 7 inch. The 7 inch jaws are slightly smaller, although there is an exception. I believe the wire jaw will fit both.
-
I went back and looked, the only
info I saw, was pictures of the
8.5 inch model.Well, there was the one upside
down.steve
-
OK, everything showed up today.
8.5, April 1949. 7, January 1949.Most of the extra jaws look to be
unused.I've seen Plierenches, since I was 12.
the 7 inch one, well the only way to
describe it, is "cute." Never seen one
before today.I'm surprised by how well these look.
Best I've personally seen.Now, fitting. All of the extra jaws will
go into the 8.5 tool, and some of them
will work there. None of the 8.5 jaws will
fit the 7 incher. The "reverse" jaw doesn't
have that groove that lines up with the angle
grooves on the fixed jaw, when used backwards.Over all, I'm a happy camper!
steve
-
@skou said:
OK, everything showed up today.
8.5, April 1949. 7, January 1949.Most of the extra jaws look to be
unused.I've seen Plierenches, since I was 12.
the 7 inch one, well the only way to
describe it, is "cute." Never seen one
before today.I'm surprised by how well these look.
Best I've personally seen.Now, fitting. All of the extra jaws will
go into the 8.5 tool, and some of them
will work there. None of the 8.5 jaws will
fit the 7 incher. The "reverse" jaw doesn't
have that groove that lines up with the angle
grooves on the fixed jaw, when used backwards.Over all, I'm a happy camper!
steve

Did you get a chance to look at the dates on both tools? Are they a matched set?
-
"8.5, April 1949. 7, January 1949."
(Quoting me, above.)Yes, that was a bit cryptic.
the 8 and a half is from April,
the 7 inch is January.steve
-
@skou said:
"8.5, April 1949. 7, January 1949."
(Quoting me, above.)Yes, that was a bit cryptic.
the 8 and a half is from April,
the 7 inch is January.steve
Naw, I just missed it. Thank you for posting it again. Darn close dates. Probably sold together considering the dates. Most people split the sets to sell them.
-
OK, am I the only one who has used a Plierench,
as an implement of bashing?I've been doing that since 1972 or so.
No, it hasn't hurt the tool(s.)
I think I could beat through a cinder block,
without doing much damage.Oh, still want to get another "cute" 7 inch
model.steve
-
"Oh, still want to get another "cute" 7 inch
model."Second one arrived today. Just as cute.
steve
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login