First mod done. I present...
-
-
-
@NKB said:
Love the scales
What have you got on the back of the blade layer?
Neil
I left the back open--no tool. I drilled the hole for the keyring into that space. The blade layer seems to work well without the back tool, so I left it out.
-
-
-
cant see the pictures :ahhh -
-
Ok, I've tried it a few ways.
First off, keep in mind that the wood saw has lots of big teeth that could catch on a tool or liner if it doesn't have enough space. So what doesn't work well for the saw may work with the metal file. Anyone with a metal file care to experiment and post pics?

Second, I put the Inline Phillips/Mag layer beside the corkscrew layer. Because the inline phillips head sticks out a little bit to the sides, over the liners, its basically a worst case scenario for putting the wood saw beside. If a wood saw configuration works with the inline phillips beside, it should work with anything else.
Third, if you see/think of a configuration I missed, tell me!
Fourth, nevermind how high the saw tip is. I'm not going to grind at the spacers until I've got something that works well.
These are ranked from worst to best, in my opinion.
Spoiler:
First up, is putting the small blade and spacer in the place of the main blade, with the saw and a spacer where the small blade normally goes.
Bad, because the small blade nick is inaccessible.
You'll need a double liner between the corkscrew layer and mag layer to stop the saw catching the phillips.
Also an old style liner without the stamped indent to get the small blade to fit.
Also, the spacer by the saw is too thick, It needs to be 0.6mm or so, and its 0.9-1mm.
Spoiler:
Next is the small blade and spacer in its usual place, with wood saw in place of main blade.
Not very good, because the saw will catch on the small blade unless you guide it in. But has potential.
You'll need a double liner between the corkscrew layer and mag layer to stop the saw catching the phillips, also one liner and the small blade spacer will have to be shaped to provide a proper rest for the saw tip.
Also, the saw spacer here in this case is too thick. Its about 0.4mm thick, and needs to be 0.2mm thick. That can be achieved by sanding.
If you used the metal saw, you might have less/no problems with teeth catching the small blade. Needs more investigation by someone with a metal saw.
-
-
@Pablo O'Brien said:
Ok, I've tried it a few ways.
First off, keep in mind that the wood saw has lots of big teeth that could catch on a tool or liner if it doesn't have enough space. So what doesn't work well for the saw may work with the metal file. Anyone with a metal file care to experiment and post pics?

Second, I put the Inline Phillips/Mag layer beside the corkscrew layer. Because the inline phillips head sticks out a little bit to the sides, over the liners, its basically a worst case scenario for putting the wood saw beside. If a wood saw configuration works with the inline phillips beside, it should work with anything else.
Third, if you see/think of a configuration I missed, tell me!
Fourth, nevermind how high the saw tip is. I'm not going to grind at the spacers until I've got something that works well.
These are ranked from worst to best, in my opinion.
Spoiler:
First up, is putting the small blade and spacer in the place of the main blade, with the saw and a spacer where the small blade normally goes.
Bad, because the small blade nick is inaccessible.
You'll need a double liner between the corkscrew layer and mag layer to stop the saw catching the phillips.
Also an old style liner without the stamped indent to get the small blade to fit.
Also, the spacer by the saw is too thick, It needs to be 0.6mm or so, and its 0.9-1mm.
Spoiler:
Next is the small blade and spacer in its usual place, with wood saw in place of main blade.
Not very good, because the saw will catch on the small blade unless you guide it in. But has potential.
You'll need a double liner between the corkscrew layer and mag layer to stop the saw catching the phillips, also one liner and the small blade spacer will have to be shaped to provide a proper rest for the saw tip.
Also, the saw spacer here in this case is too thick. Its about 0.4mm thick, and needs to be 0.2mm thick. That can be achieved by sanding.
If you used the metal saw, you might have less/no problems with teeth catching the small blade. Needs more investigation by someone with a metal saw.
Excellent work.
I've been thinking about doing this for a while now (with the metal file) but never got round to it. Definitely worth a try. -
Overall, when it comes to putting the wood saw in the corkscrew layer, I'd rather ditch the small blade and take up the extra space with washers.

Like this:
Spoiler:
The saw spacer is too thick. Its 0.9-1mm, and needs to be 0.6mmOr like this:
Spoiler:
The tweezer/mag end needs an additional 0.4mm spacer for everything to fit right.
And the saw spacer needs to be sanded down to half the thickness.The latter is my favorite, and its basically the same idea as what Jaya_Man did, only with small blade spacers instead of a rest made from a scissor spring:
</topic/68332 -
Nice try Pablo....would have been sweet to get the small blade on there.
Big fan of your recent posts about mod attempts with with all the pics taken along the way. Thinking about attempt my first mod and they're definitely making me feel like I have a better grasp going in.

-
Would the in line awl work in the place of the small blade
seems like it would be more out of the way than the blade but sourcing one is always the problem 
-
Excellent work though either way
Finding out things like this is always a great source when modding

-
Thanks.

@tommywp said:
Nice try Pablo....would have been sweet to get the small blade on there.Big fan of your recent posts about mod attempts with with all the pics taken along the way. Thinking about attempt my first mod and they're definitely making me feel like I have a better grasp going in.

When it comes to modding, I think taking it apart is the hardest bit, but only if you're trying to save the brushings

I recommend getting beater SAKs online for practice and spare parts "just in case".
And experiment with preening, find what technique works for you.
-
@King_Gorilla said:
cant see the pictures :ahhhRight click, select open image in new tab (or whatever). Photosmurfet page for the image opens.
tried that. It just opens photobucket in a new tab with the same "Is this your picture" photobucket blaw blaw ect. lame poop image

-
@King_Gorilla said:
@King_Gorilla said:
cant see the pictures :ahhhRight click, select open image in new tab (or whatever). Photosmurfet page for the image opens.
tried that. It just opens photobucket in a new tab with the same "Is this your picture" photobucket blaw blaw ect. lame poop image

Yeah, it appears that the image link redirects to the ransom image.

-
@Pablo O'Brien said:
Thanks.
Nice try Pablo....would have been sweet to get the small blade on there.
Big fan of your recent posts about mod attempts with with all the pics taken along the way. Thinking about attempt my first mod and they're definitely making me feel like I have a better grasp going in.

When it comes to modding, I think taking it apart is the hardest bit, but only if you're trying to save the brushings

I recommend getting beater SAKs online for practice and spare parts "just in case".
And experiment with preening, find what technique works for you.
Be careful with your preening Pabs hun

-
-
@Pablo O'Brien said:
Thanks.

Nice try Pablo....would have been sweet to get the small blade on there.
Big fan of your recent posts about mod attempts with with all the pics taken along the way. Thinking about attempt my first mod and they're definitely making me feel like I have a better grasp going in.

When it comes to modding, I think taking it apart is the hardest bit, but only if you're trying to save the brushings

I recommend getting beater SAKs online for practice and spare parts "just in case".
And experiment with preening, find what technique works for you.
Be careful with your preening Pabs hun
And your brushing, too...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
