Supertool 300 VX upgrade (Mod badge request too)
-
Yeah Evil's photo links are broken (Photobucket).
-
Someone made bits from scratch - perhaps that was Evil.
Someone else (Loki?) drilled a hole through a bit and glued a small screwdriver into it. -
/post/1080147

-
Thanks - you really went above and beyond for this

Looks like an idea I might
pinchadapt...Edit: more than one idea there that I like, none of which need the small bit holder to be located in the ST300 (VX). That's decided then, I'm putting the awl back in. Thanks to all those thinking along with me

-
Here then is Part II of the writeup, featuring the making of The Ring and adaptations of a few other items, followed by reassembly of the tools into the serrated-blade side handle. Also, I'm taking the opportunity to reorder the tools in the straight-edge knife handle and to replace the small bit holder with the awl as well as a spacer washer with the previously omitted lanyard ring. Reordering had become necessary following the discovery that the plier head was just rubbing against the can opener - we can't have that, can we?
Here goes!
We start by making The Ring, actually a sleeve which fills the space between the (Surge) saw/file blade exchanger pivot hole and the Supertool's pivot. A copper tube of 6mm outside and 4mm inside diameter is drilled and then turned and parted to make it 5.5 mm outside and 4.8 mm inside as well as 3.0 mm long. While turning and parting I keep a 4.7 mm drill bit reversed in the drilled hole as a support, with some oil to reduce friction. The result is shown on the original pivot.



Then I use the sleeve to align the lengths of the saw/file blade exchanger exactly with the original Supertool saw, and clamp the lot with a small vice grip (sweet little thing, that). I do this to get the position exactly right in order to be able to adapt the exchanger's outer profile to that of the original saw. I use a variety of tools to pull this off, as shown below as well: small bench grinder, Dremel with cutting disc or with a barrel grinder, various files and a vice.




The result is shown below. We want the exchanger lo lock as the old saw did.

Some of the files used, plus tweezer and needle:

The exchanger parts look like this (bottom pic compares the profile with the saw and shows the pivot and ring again):


Meanwhile I took the opportunity to make some slight adjustments to the awl (thinned it a bit) and the large screwdriver (made a small pry bar out of it):

This is the assembly order for the serrated-blade handle (oops, the positions of the exchanger and washer in the picture should be reversed, please note):

As already announced, I also reordered the tools in the other handle, as follows:

This is the assembled straight-blade handle (with an oil pen I used and the tweezers):

This the assembled serrated-blade handle with modified Surge blade exchanger fitted:

It turned out that the scissors and awl were in collision. I ground off a bit from the scissors handle tab: problem sorted!

Here the SuperTool 300 VX in its full glory! All tools work, extend, retract and lock as intended.

This concludes the writeup. Many thanks to other forum members from whom I have unashamedly stolen parts of my mod, to wit at least Zoidberg, Toolslinger and Obi1shinobee
as well as all those who gave tips regarding the awl. I have plans for the small screwdriver bit holder, but those are not necessarily part of this mod and will be reported in a new thread whenever ready.Good luck to those that wish to repeat these exploits!
Oh yes - can I have my badge now please?

-
@Dutch_Tooler said:
Oh yes - can I have my badge now please?

Yeah sure, can you submit the request via your profile please...
-
Nicely done DT !

-
Awarded.

-
Congratulations

-
Sweet!
-
Nice job

-
Thanks to all!

Special points go to whoever guesses which picture contains a small mistake I have not yet announced - or perhaps rather two.

-
:ahhh :ahhh :ahhh :ahhh :ahhh :ahhh :ahhh :ahhh
-
Hmmm.... about the small screwdriver, pity that the PST-inspired solution in the pic does not really work, as there is no positive lock at the level of the plier pivots when you clamp the tool shut, like there is on the original:

Sent on my SM-G930F with Tapatalk
-
The small bit can be wedged under the lock on the ST300. I just thought of this and tried it out, works pretty good



-
Just tried it on my Rebar and it also works

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
Thanks again!