Chinese steels
-
I don't own either steel since it just never interested me, but they should be on par for a $10 knife.
If Spyderco, Kershaw, CRKT, Benchmade, Meyerco, Buck and SOG all think 8Cr13MoV is a good steel to use in knives that cost a heckuva lot more than $10 I'm inclined to agree with them.
I don't have a problem with the 8Cr13Mov steel. It honestly doesn't seem that much softer than the VG10 in the other Spydies I have... Maybe I just haven't really beat on them yet for it to be an issue, but so far I've had no problems. While I don't baby my knives, I do make a point of taking care of my equipment, so take that for what it's worth.
-
@Heinz Doofenshmirtz said:
I don't own either steel since it just never interested me, but they should be on par for a $10 knife.
If Spyderco, Kershaw, CRKT, Benchmade, Meyerco, Buck and SOG all think 8Cr13MoV is a good steel to use in knives that cost a heckuva lot more than $10 I'm inclined to agree with them.
I don't have a problem with the 8Cr13Mov steel. It honestly doesn't seem that much softer than the VG10 in the other Spydies I have... Maybe I just haven't really beat on them yet for it to be an issue, but so far I've had no problems. While I don't baby my knives, I do make a point of taking care of my equipment, so take that for what it's worth.
8Cr13MoV was developed in conjunction with Spyderco, and it was originally meant to be a Chinese version of 440C. The original Byrd line was marked as such. However, alloying and usage wise it's almost identical to AUS-8 steel. The difference is that 8Cr13MoV can be hardened a few points higher on the Rockwell scale than AUS-8 without becoming brittle, but the latter is slightly more corrosion resistant. It's not a bad steel by any means. Not super-duper high end, but a good, solid everyday usage steel.
There is actually a Chinese steel with similar characteristics to VG-10 though, and it's 9Cr13CoMoV. It adds cobalt for edge retention and it's apparently quite good. I don't have any long-term experience with the steel like I do with VG-10 or 8Cr13MoV steel, though. You can find it in some Benchmade models in the Harley-Davidson line as well as the discontinued Pika 2 line.
-
Actually 9cr13comov is a steel I would like to play with, and I am looking forward to it. As you said it is very similar in composition to vg-10, which is a steel I really like.
-
That 9-13 sounds interesting. Although I can't honestly say I need another knife right now, considering that in the past couple of months I bought a new Endura, Delica, Dragonfly 2, Byrd Wings, and have a Stretch 2 on order right now... :o
I'm very pleased with the Wings in fact... both blades are the 8Cr13MoV and it's a very nice tool. I got it for $30 shipped from Jeff at Cutlery Shoppe. It looks like it'll be a great camp / utility knife. I'm still undecided as to how I'm going to purpose it though... I've been thinking I should put it on the waist belt of my hiking pack, but I was also thinking about putting my new Work Champ there as well. I think the Wings will be a better choice for that though, and I'll probably stow the Work Champ inside the pack itself so I have it for other types of small jobs that it'll be more appropriate for than just general hacking and cutting. I'm planning on a hike this weekend, so I might get a chance to put it through some paces.
-
I've had no trouble with any of the spyderco china knives and I have a friend who uses srm all the time and loves there stuff. For 10-15$ what can you lose really? I say try it.

-
batjka104,
Just get yourself either a Tenacious or a Resilience; they're both great knives. If you want some thing that is going to specifically be an EDC knife, then get a Persistence; it's basically a slightly smaller Tenacious. It's blade shape is nearly the same, but it's about a 1/2" shorter. Many people say the Resilience is just a bigger Tenacious, but I don't agree. It's almost a full inch longer and an ounce heavier, and its blade profile is markedly different than the Tenacious. Regardless, you should check them all out.
I'd recommend you go with Cutlery Shoppe, Jeff Loffer, the owner, has great service and his prices on Spydercos are the best I've seen. Last time I checked he had the Resilience for $36 and the Tenacious for $32.
-
Say Heah Guy's, Yup I have a couple of Steel Will Knives, I really like the steel, I just wish my Druid 230 was a bit wider so it would increase the weight a little, But my Druid 240 Me Like.,,. p
Sent from my SM-J700T using Tapatalk
-
I have a CRKT in 8Cr13MoV and it's a 'cut once sharpen once' steel IMO. My GEC 440C is considerably better for edge retention.
-
There is only one problem with Chinese knives.
Are you getting what is printed on the blade?8Cr13MoV is fair and I trust it is what you are getting from the big name makers.
Other companies can use whatever they want and then write whatever they want on the blades.
Is it actually even 8Cr13 you are buying? -
Not all knives made in China are poor quality.
I recently bought the smaal Buck cano, two bladed knife, made in China for Buck under contract.
The blades are made from a stainless steel traditionally used for lining. It is a fraction softer, but it is holding its cutting edge well. I have used mine now for at least six months. It compares in my opinion to the Swiss Army Knives and keeps its edge longer than Leatherman blades.
I also have a Tekut, wich is well made.
I am now 54, realising I will not live forever, so I dont buy the very best anymore, as I will not be able to sharpen up a blade. If I could sharpen a SAK narrower by 3mm with a Lansky kit in 35 years, I will not do so with a cheapo. I need reasonable workmanship, price and edge holding.
-
I've been carrying and using this Sanrenmu LAND 910 for a couple of months now. It has 12C27 steel and this thing holds a great edge. I've only had to touch it up once on my Lansky turnbox and it's shaving sharp. It's the perfect size for EDC IMO. It also has bearing in the pivot and is a nice weight, not to heavy due to the hollowed out frame.
Under $20 on E-Bay



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login