Non Multitools
-
@Grant Lamontagne said:
What do you do when you find an SAE nut?Def
Walk away and say it can't be fixed

-
I've taken some pictures of various tools which I've come to like over the years. Hopefully some might be interesting to others as well.

-
Sometimes I've had to argue with heavy or stuck stuff. And I've come to the conclusion that big is better for curing such issues. So I can highly recommend the back saving long lazy arm for sockets in the first picture, as well as a proper sized forged breaking bar. Actually the tiny breaking bar is nice too for more delicate stuff. (17mm socket included as size reference).
-
Spanners have standardized lengths loosely based on the torque the corresponding sized nuts and bolts are supposed to take and expected human strength. To make work just a little easier for myself when loosening stuff I usually use non-standard spanners that are longer than normal. (Normal 24mm spanner included for comparison).
-
I once had to measure a series of a particular part fairly precise. I ended up getting an oversized caliper. It figures in weirdly many selfies with people who has visited...
-
While the oversize one is fun, this absolute digital caliper in a more normal 8" / 20 cm size is a lot more useful. And it is used a lot - maybe the tool I use the most.




-
-
-
Another one I like for measurement and marking at once is this vernier scriber thing. Great for marking a certain distance or cross from edges or similar.
-
Some years ago I needed a portable drill press. I ended up with this magnetic base drill press which basically sticks hard to any magentic surface - including sideways on wall, upside down etc. For drilling in non-magnetic materials I added the little metal bar to the left which I can clamp down to anything and then stick it to.
-
For work with hydraulics or pipes these splitting and ratcheting spanners are quite nice. They are fairly slim and will go around a pipe or hose. They ratchet one way so to turn direction you'd have to change the grip. I have the broad slim socket thing just for hydraulic manifolds - they all seem to have been designed by people who assume nothing will ever need to come loose ever after and thus room for tools are not needed...
-
Talking about sockets I've come to like the Kamasa ones to the left. Compared to most normal sockets (example on the right) the can also be gripped from the side by a spanner or hole spanner. The non-round outside also makes them a lot easier to turn just by hand for when that goes faster.




-
-
-
My favorite little portable screwdriver. It is very compact yet has a nice grip and the 4 most used bit ends. And was dirt cheap too.
-
Over the years I've landed on Wera as my favorite screwdrivers. I'm not really in love with the grip, but the business ends are very good and grips like no other. The yellow series can also be grabbed from the side with a spanner for more torque, and have a full tang so one can whack them with a hammer. (Might not actually solve anything, but hammering just feels like therapy sometimes :D ).
-
and 12. Certain applications need more precise torque than my blunt hands can provide. For those this Swisstool/ Garant torque system is great. Torque can be adjusted to what you need, and there are inserts available for all the normal suspects. As well as adapters for bit sockets and 1/4" drive. Can't help but like this one.




-
-
Great thread and some great tools.
Once we've moved I'll have to sort my toolboxes and get some photos up. -
Great pics there Vidar!
I'll have to take some pics of my calipers too- after I got injured a couple of years ago I bought a set of digital calipers so I could start measuring things to try and recreate them in CAD software. I had some limited success with the software, but I still use the calipers to measure a lot of things. It's amazing how handy they are, and I often wonder how I ever got along without them.
Def
-
-
The germans make some very nice pliers. Here are some Knipex ones. The black head Cobra ones are like improved water pump pliers. The blank head pliers wrenches are just great - their jaws remain parallel and will function as a ratcheting spanner among other things. And the Rapter down left in picture is a specialized nuts and bolt gripper.
-
For electrical and cable work the three to the right really saves time. The middle one will cut around the outside of a cable to a specific depth, and the edge can then be twisted 90 degrees and cut along the cable. Great for quickly getting to inner cables. If the outside is tough the one second to the left will usually still cut off the outside without harming any cables inside. And the hexagonal end crimp tool to the far right really helps securing good cable ends and proper reliable connections.
-
The little mirror with a light can be a lifesaver in tight spots. (Another candidate is taking a photo with the cellphone if your hand fits). The little pen is an oil pen - great for local cutting oil adds when machining. And the crazy looking plier to the right is a zip tie tightener and cutter. The thing works great!
-
Some various tidbits I've found useful. A centered stainless steel wirebrush; great for welding preparation. Two burr and edge removers - the blue one for inside holes. And the last one is a steering add-on for threading rods - it makes it easier to get the threads proper parallel to the rod every time.




-
-
@Grant Lamontagne said:
Great pics there Vidar!I'll have to take some pics of my calipers too- after I got injured a couple of years ago I bought a set of digital calipers so I could start measuring things to try and recreate them in CAD software. I had some limited success with the software, but I still use the calipers to measure a lot of things. It's amazing how handy they are, and I often wonder how I ever got along without them.
Def
Yes, it is a measuring multitool :)
-
I really like the style of wrench that you have here:
The one on the far right.
I don't have one but I have often thought that the adjustable size on one of those would be extremely useful. We have a review of a similar one on the Main Site and I have often thought of getting one.
Def
-
That link was a fun multitool. Might be too bulky in many use cases though?
The one to the right can certainly grip some round or six sided stuff quite hard. I think it goes up to 4-6mm or so.
Its main purpose is to deform end crips onto electrical wires and make notches which helps keeping the wire securely stuck in whatever you connect the end to. (The more common ones leave a square end). It really helped reduce issues due to bad connection for electrical power or signals.
Before this I used more normal cheap crimping tools, but once in a blue moon there would be an error - usually one of those annoying hard-to-find ones that are just there sometimes. Needless to say causes of great frustration and expense. All such errors went away with this one - great investment!
-
Oops, I guess I was thinking of a different tool then. My excuse for not knowing that is that I am horrible when it comes to electrical work is that I don't tend to do much of it. Electricity and I rarely see eye to eye, and when we do it is usually just an excuse for electricity to poke me in it....

That having been said, last week I rewired my trailer- apparently you can get worse at electrical work than me- a standard 4 pin trailer connector was then wired into a six pin connector (both male and female) then to two four pin connectors (again, male and female ends) and then into the two brake lights and nothing else. I ripped all the wiring out and just replaced them with... wire. Just four wires, which is what should have been there in the first place, and all of the new wires run through conduits to make sure they didn't hang or snag on anything.
Def
-
If you can do a trailer connection you are more qualified than me for sure. Trailer connectors just seems to be a mess of standards and connections. (I'm sure it is all perfectly clear to the initiated though).
I actually saw eye to eye with electricity many years ago on a steel construction. Close enough to some 400v wire ends for the electricity to jump across the gap and onto my nose. It was not supposed to be live, but it sure got me very lively. :ahhh

I had the odd smell and taste of burnt hair for the next two weeks or so. Live and learn I guess.

-
I went from Best Buy Technician with 3 tool bags to an AV install company with 2 crew cab dodge gooseneck dually trucks and 2 fully stocked 26' trailers. :o :o :o
I still carry my Knipex from Best Buy as they are fantastic tools. Husky makes a fine socket set. We beat the hell out of the sockets and ratchets and they still hold up just fine. Klein has glow in the dark handle tools now. I bought a pair of diagonal cutters. Awesome when you're working in the ceiling.
I need recommendations on IT scissors besides those Greenlee or Klein ones. They don't fit my big hands for fiddling with cat cable,
-
@Vidar said:
If you can do a trailer connection you are more qualified than me for sure. Trailer connectors just seems to be a mess of standards and connections. (I'm sure it is all perfectly clear to the initiated though).I actually saw eye to eye with electricity many years ago on a steel construction. Close enough to some 400v wire ends for the electricity to jump across the gap and onto my nose. It was not supposed to be live, but it sure got me very lively. :ahhh

I had the odd smell and taste of burnt hair for the next two weeks or so. Live and learn I guess.

I have yet to hook up said trailer and see if it was successful, or if the whole mess bursts into flames. Its simple wiring but i am still quite certain that I have screwed it up somehow.

Def
-
@Pacu said:
I went from Best Buy Technician with 3 tool bags to an AV install company with 2 crew cab dodge gooseneck dually trucks and 2 fully stocked 26' trailers. :o :o :oI still carry my Knipex from Best Buy as they are fantastic tools. Husky makes a fine socket set. We beat the hell out of the sockets and ratchets and they still hold up just fine. Klein has glow in the dark handle tools now. I bought a pair of diagonal cutters. Awesome when you're working in the ceiling.
I need recommendations on IT scissors besides those Greenlee or Klein ones. They don't fit my big hands for fiddling with cat cable,
Gerber Cable Dawg?

Sorry, that's the best I've got.....
I didn't know you'd left BB though. Congrats man, it sounds like a real step up!
Def
-
@Vidar said:
13. The germans make some very nice pliers. Here are some Knipex ones. The black head Cobra ones are like improved water pump pliers. The blank head pliers wrenches are just great - their jaws remain parallel and will function as a ratcheting spanner among other things. And the Rapter down left in picture is a specialized nuts and bolt gripper.-
For electrical and cable work the three to the right really saves time. The middle one will cut around the outside of a cable to a specific depth, and the edge can then be twisted 90 degrees and cut along the cable. Great for quickly getting to inner cables. If the outside is tough the one second to the left will usually still cut off the outside without harming any cables inside. And the hexagonal end crimp tool to the far right really helps securing good cable ends and proper reliable connections.
-
The little mirror with a light can be a lifesaver in tight spots. (Another candidate is taking a photo with the cellphone if your hand fits). The little pen is an oil pen - great for local cutting oil adds when machining. And the crazy looking plier to the right is a zip tie tightener and cutter. The thing works great!
-
Some various tidbits I've found useful. A centered stainless steel wirebrush; great for welding preparation. Two burr and edge removers - the blue one for inside holes. And the last one is a steering add-on for threading rods - it makes it easier to get the threads proper parallel to the rod every time.
Love the Knipex pliers!
-
-
It's a definite possibility of there's enough interest.
Def
-
Seconded

Sent on my SM-G930F with Tapatalk
-
Poked.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login