What did you use your Leatherman for today?
-
And again... see thread linked above.
Sent on my SM-G930F with Tapatalk
-
Used the file on my PS4 to clean up the threads on a sink drain fitting at my wife's office, to replace the P-trap. Old drain fitting had a slow leak, and rusted completed off the sink before they caught it. PS4 cleaned up the threads nicely!
-
Spent a vacation in Turkey last week and since I love coffee I brought a can of it with me home. When I attempted to open it the handle ring broke and I used pliers to open the can. Wave did great of course, yet the coffee might be way better [emoji23]. Sorry, forgot to take any pics [emoji880]
-
But without a pic this did not happen! :ahhh
-
Needed to remove the bottom panel on my wife's laptop (internal battery wasn't working). Most of the screws were torx 6, but one tiny one in the centre of the case was much smaller --- so to the rescue comes my modded Juice with the small bit cross-head driver.
Re-seated the connectors from the battery and it works again. Job done.

-
Way to go

Love that mod
-
-
Fixed a hairdryer recently and used Wave a bit. Large flathead as a pry bar while opening it and then the pliers to... catch and remove the dust [emoji23] Could not use a bit kit since this hairdryer has one of those more rarely used screws with two dots on top. Anyhow, it works much better now.
P.S.: sorry, only have a picture of a fan without a cover so I’d remember what it should look like in the end if I forget [emoji23]

-
And today I’ve disassembled my Raspberry Pi setup in order to replace a real-time clock battery. Used Wave’s standard bit with an extender to unscrew the extension board and then the smallest screwdriver on Micra to pull the battery because I forgot about an eyeglass screwdriver in Wave [emoji23]



-
Me again [emoji23]. Had some decent time outdoors and used my Wave of course.
First I used it to cut off a small piece of wood

Then engaged a knife to get some shavings

And start a fire with that, but I had no luck - the wood was a bit wet, so I added some really dry oiled shavings from Light My Fire and used a lighter to have a fire started [emoji854].

And while my fire grew I decided to adjust a break handle on the bicycle I rented for today. It had a hex screw and I had a bit kit, so it was a pretty easy game.


Being done with that I finally could just sit back and have a cup of hot herbal tea with honey [emoji518] [emoji56]


-
Trust me guys, it will work! I'm electrician!
>:D >:D
-
@Vjeko Posavac said:
Trust me guys, it will work! I'm electrician!
>:D >:DThe only way when you need to find out what fuse that outlet is on, without being able to shut every fuse off one by one (like when there are servers in the building)
Did it myself, twice in 7 years... but with isolated pliers instead of a stainless tool... -
@ alexanderre
I like the way you spend you'r outdoor time
@mechanickal
It's OK, i'm electrician! I mean, what's the worst thing that can happen?

-
@Vjeko Posavac said:
@ alexanderre
I like the way you spend you'r outdoor time
@mechanickal
It's OK, i'm electrician! I mean, what's the worst thing that can happen?

Thanks, bud [emoji2]
-
Used Micra to open a new package of herbal tea today.



-
Used the awl of my Rebar today to help replace a door latch assembly on my truck. Control rods that bridge the gap between interior door handle and the latch, or exterior door handle and the latch...these rods are held in place by thin clips that slide over the tab and ends of the rods. They had to be removed before the latch would come free.
In the pics, the clip in the palm of my hand slides over the tab that the awl is pointed to. Then the blue end of the rod is forced through the hole in the tab, also through the clip. Easy to assemble back up, but it was the toughest, most fiddly part of the job to undo in the first place.
-
Rod, clip, tab mechanism
-
Latch installed in doorjamb with old one in foreground
-
During the process I also used Rebar to remove/ replace the odd Philips screw, and to help pull the nylon tabs that held the electrical harness in place.
The door now closes as it should instead of leaving a quarter inch gap that rattled over every bump and allowed wind and rain in. Back to some semblance of normalcy, althoughthough a 24 year old K1500 Blazer Silverado always presents me with something else to work on.
The heat is not working. That may be the next project before this New England winter.
Knock on wood but although it needs some work, it starts right up and runs as well as my girl's Nissan Murano.
She may not look like much, but, she's got it where it counts.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
