The Gerber MP1 Thread
-
Looks like a good start and warm up to get a feel for it! Nice pics too!
I'll be watching from the sidelines to see how yours holds up.
-
@gerleatherberman said:
Looks like a good start and warm up to get a feel for it! Nice pics too!
I'll be watching from the sidelines to see how yours holds up.
Don't stay on the sidelines! I hope if yours gets some more use you'll share your thoughts here.
-
OK. You convinced me.
I will give the MP1 a fair shake for a few days. :)
We will see if the MP1 has actually earned the MP prefix.
-

I hope you enjoy it.
I have given my mp1 a fair bit of pain, but it has endured (unlike LM tools). It does feel much flimsier than it really is!I hate the pouch too, not even spare room for extra bits.
-
interesting read and most beautiful pics! Do you use your phone for them :o?
The tool seems really nice from the outside and I'll follow with interest to see if it deliverssad for the sheath, an element as important as the tool it carries IMO
-
@ThePeacent said:
interesting read and most beautiful pics! Do you use your phone for them :o?
The tool seems really nice from the outside and I'll follow with interest to see if it deliverssad for the sheath, an element as important as the tool it carries IMO
Thanks! Yes I use my phone for all my pics. Samsung Galaxy S7.
-
Got an old slim LM PST sheath?



-
I bought a the premium Leatherman sheath for the Wave size (4.0 tall) because I hate velcro.
Requires a little user work (blow dryer or alcohol) to stretch to carry the mp1, the 4.5 surge size would fit much better, since it's 4.3 tall.
Genius use of the PST sheath grant.
I wonder how difficult adding a snap to the Gerber sheath would be? Anyone ever try?
-
Good thread folks.

-
Good tips! I can't imagine adding a snap would be too hard.
-
Thanks Raven!
Indeed Clown. A simple kit for adding the snap buttons can be found online.
You know, the Strata and BullRush have the same sheath design and have button snaps. I wonder why Gerber went with velcro on a MSRP $110 tool when the Strata and BR are much less MSRP.
Oh well. We'll figure something out. I think it is high time certain aspects of the MP1 are taken seriously. It seems to be a well designed tool with just a couple of hiccups overall. Peening the plier joint seems to have helped the plier play and being drop forged, it should hold up a little better than standard internal spring cast pliers. I do like the fine point needle nose too for delicate work. And the nearly flush anvil cutters are a much needed feature in the MT world. The anvil style takes stress off the pivot to a large extent. Bypass cutters have caused me a lot of time pressing the pivot back on many tools.
IMO. It is one of the best looking MTs out there! :) -
I was replacing broken springs most of the day today so the MP1 didn't see much action. Did have time for a quick pic tho.

-
Used my MP1 to split and strip wire while replacing some safety eyes today. Used the prybar to pop the cover off this door opener and then used the larger flathead to adjust the travel limits.

Used the blade to cut open the packaging around a piece of replacement glass. Used the pliers to remove and reinstall the master link on the drive chain of a commercial door operator.
I'm really enjoying using the MP1 this week. So far I think my biggest complaint is the sprung pliers👎. I almost dropped it off the top of a 12 foot ladder today trying to balance it on there with a set of vice grips, a hammer and a wrench. Can't really just drop it in you pocket for a minute either or you'll spend the next 10 min trying to get back out.
-
I appreciate the info as I have been thinking about getting one.
Keep posting and I will keep reading.
-
I put my MP1 through a few trials I put all my new multitool EDC prospects through.
After peening the pliers pivot, to be clear.
I used the pliers to open the pipe plugs on a handful of 55 gallon drums of oil we had at work and to close the hydraulic cylinders on large jack stands.
This is about the most grueling test I could come up with to test resistance to torsional load (I've snapped pliers on 3 skeletools doing this as a note, and one wave pliers)
The mp1 withstood the sideload without gaining any slop.
Next I used the regular pliers section to hold onto a 20 x 2.5 stud while I ran a die down some bothered up thread.
Again no slop gained.
I then used the needlenose to place and remove .003 (width of a hair for reference) shims underneath some large steel weldments we needed to make fine leveling adjustments on.
I've used the bit driver on high feed milling cutters to back out torx insert screws. Without antiseize on the screws, it did twist a little but removed the screws. Have repeated that test multiple times on different sized cutters and screw sizes. All the way up to T30 torx screws in large diameter spade drills.
Used the pry tool and screwdrivers to shimmy out stuck collects and cutters. Which is a ton of torsional force on the pivots/tools
Maybe I got a good one, but If you can break the bit driver or pliers.
I'd like a video.
For me and my purposes as an EDC this is the "Wave" killer and I'll be sidelining my MUT, atleast for now.
-
All sounding very good gents.
Clown; I'm with you on sprung pliers though, the times they are a real advantage are hugely outweighed by the times they are a PITA. :-\ -
@Gareth said:
All sounding very good gents.
Clown; I'm with you on sprung pliers though, the times they are a real advantage are hugely outweighed by the times they are a PITA. :-\Agreed. Look much space this thing takes up.

I watched the pliers tips misalign themselves while twisting open this cotter pin. But they went back to normal.

I also noticed the handles 'squish' a little while squeezing hard on the pin to straighten it before reinstalling it. Nothing to cause worry as of yet though.
-
Those are the two things I was worried about as it is not a heavy looking tool.
Keep the info coming.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login