Remade Knives SAK 91mm scale 3D model released to the public for free
-
The rough look of them is nicer personally.
Sent from my iPhone using Tapatalk
-
@an0nemus said:
I get conflicting opinions also about the CF nature of these scales. Whatever it is, it's tough. Even a group mate's effort to use dremel and smoothen it was disastrous


I might be wrong but it looks like the material he used to print the scales is a mix of carbon fiber and PLA ( a type of biodegradable plastic) which does not take heat well. i would recommend next time getting them printed in ABS or nylon, and to make sure that the person printing the scales uses a smaller print nozzle
-
I get conflicting opinions also about the CF nature of these scales. Whatever it is, it's tough. Even a group mate's effort to use dremel and smoothen it was disastrous



I might be wrong but it looks like the material he used to print the scales is a mix of carbon fiber and PLA ( a type of biodegradable plastic) which does not take heat well. i would recommend next time getting them printed in ABS or nylon, and to make sure that the person printing the scales uses a smaller print nozzle
Feedback to a related question by me in a 3D printing forum suggests that CF holding filament should be printed with at the smallest a 0.5, or better 0.6, mm nozzle...
-
I get conflicting opinions also about the CF nature of these scales. Whatever it is, it's tough. Even a group mate's effort to use dremel and smoothen it was disastrous



I might be wrong but it looks like the material he used to print the scales is a mix of carbon fiber and PLA ( a type of biodegradable plastic) which does not take heat well. i would recommend next time getting them printed in ABS or nylon, and to make sure that the person printing the scales uses a smaller print nozzle
He did say it CF were added in the material. So it might be as you described. Two sets were printed, one with ABS and one with CF filament. Todate, no one has tried putting on the ABS yet as all of us are fascinated by the "CF" scales :D
Thank you again for releasing the 3D data to the public, Brandon! It was so generous of you

-
I get conflicting opinions also about the CF nature of these scales. Whatever it is, it's tough. Even a group mate's effort to use dremel and smoothen it was disastrous



I might be wrong but it looks like the material he used to print the scales is a mix of carbon fiber and PLA ( a type of biodegradable plastic) which does not take heat well. i would recommend next time getting them printed in ABS or nylon, and to make sure that the person printing the scales uses a smaller print nozzle
He did say it CF were added in the material. So it might be as you described. Two sets were printed, one with ABS and one with CF filament. Todate, no one has tried putting on the ABS yet as all of us are fascinated by the "CF" scales :D
Thank you again for releasing the 3D data to the public, Brandon! It was so generous of you

I'll pm you my adres for those ABS ones

-
I get conflicting opinions also about the CF nature of these scales. Whatever it is, it's tough. Even a group mate's effort to use dremel and smoothen it was disastrous



I might be wrong but it looks like the material he used to print the scales is a mix of carbon fiber and PLA ( a type of biodegradable plastic) which does not take heat well. i would recommend next time getting them printed in ABS or nylon, and to make sure that the person printing the scales uses a smaller print nozzle
Feedback to a related question by me in a 3D printing forum suggests that CF holding filament should be printed with at the smallest a 0.5, or better 0.6, mm nozzle...
Admittedly, the first batch were of better quality than the 2nd batch. I'm not sure if this has anything to do with the nozzle used. But I'll share with him your feedback, DT. Helpful, as usual. Thanks!

-
I get conflicting opinions also about the CF nature of these scales. Whatever it is, it's tough. Even a group mate's effort to use dremel and smoothen it was disastrous



I might be wrong but it looks like the material he used to print the scales is a mix of carbon fiber and PLA ( a type of biodegradable plastic) which does not take heat well. i would recommend next time getting them printed in ABS or nylon, and to make sure that the person printing the scales uses a smaller print nozzle
He did say it CF were added in the material. So it might be as you described. Two sets were printed, one with ABS and one with CF filament. Todate, no one has tried putting on the ABS yet as all of us are fascinated by the "CF" scales :D
Thank you again for releasing the 3D data to the public, Brandon! It was so generous of you

I'll pm you my adres for those ABS ones

Okay, Nick!

-
So seems like Jessan is actualy going to send them my way

Thanks buddy!
Now I do feel like a cheap smurf again though

Way to generous people here... -
@Mechanickal said:
So seems like Jessan is actualy going to send them my way
Thanks buddy!
Now I do feel like a cheap smurf again though

Way to generous people here...Just passing forward the good karma in MTO, Nick

-
@Mechanickal said:
So seems like Jessan is actualy going to send them my way
Thanks buddy!
Now I do feel like a cheap smurf again though

Way to generous people here...
8) -
Made these up with an SLS machine in Nylon 12. Will dye them later on



-
Grabbed a set from them on Etsy. Put on my Tinker that had been blacked out by syph007, for the previous owner...





Sent from my iPhone using Tapatalk
-
Had a go at this tonight. Not quite there yet but heading in the right direction.
Looks best in 2 tone imho.

-
Had a go at this tonight. Not quite there yet but heading in the right direction.
Looks best in 2 tone imho.
That two-tone does look interesting...and unique

Almost forgot. Do I have a set of these coming my way??

I'll trace where they are right now, Mechanickal [emoji53]
-
Had a go at this tonight. Not quite there yet but heading in the right direction.
Looks best in 2 tone imho.
That two-tone does look interesting...and unique

Almost forgot. Do I have a set of these coming my way??

I'll trace where they are right now, Mechanickal [emoji53]
Hi, Nick! PM sent. Bad and good news [emoji37][emoji16]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
