Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Getting That "Snap" Back?

Scheduled Pinned Locked Moved Swiss Army Knights Forum
10 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Getting That "Snap" Back?
Getting That "Snap" Back?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • this_is_nascar Offline
    this_is_nascar
    Posts: 797
    this_is_nascar Offline
    this_is_nascar
    wrote on last edited by
    Quote Reply

      Is it simply a matter of cleaning your SAK in order to get that snap back? Several of mine no longer snap back in place, rather they just silently close when pushed.

      Sent from my XT1635-01 using Tapatalk

      1 Reply Last reply
      • VICMAN Offline
        VICMAN
        Posts: 15,047
        VICMAN Offline
        VICMAN
        wrote on last edited by
        #1 Quote Reply

          After removing any dirt from the knife I have had the best luck restoring the snap using 3-IN-1 oil.

          After applying the oil to the knife at the base of the blade where it meets the backspring, open and close the blade a number of times until it frees up.

          I have used WD40, REM OIL, VIC OIL, and various others, but the 3-IN-1
          seems to restore the snap the easiest for me.

          1 Reply Last reply
          • cody6268 Offline
            cody6268
            Posts: 6,250
            cody6268 Offline
            cody6268
            wrote on last edited by
            #2 Quote Reply

              Typically cleaning the pocket lint and other nasty stuff out of the pivot area by repetitively opening and closing the submerged blade then oiling it (with 3-in-1 or gun oil, my two current choices) should bring it back. If that doesn't work, I check for a damaged liner, then file the damaged, raised area away. And if that doesn't work, you might as well contact warranty. It's probably a worn tang, damaged pin, or backspring.

              1 Reply Last reply
              • Mactire404 Offline
                Mactire404
                Posts: 842
                Mactire404 Offline
                Mactire404
                wrote on last edited by
                #3 Quote Reply

                  This is how I do it:

                  SAK Cleaning
                  Getting rid of large particles

                  • Clean under running water with a brush, tools closed
                  • Clean under running water with a brush, tools open
                  • Open/close tools under running water

                  Getting rid of oils and small particles

                  • Place tool in a ultrasonic cleaner with properly warmed water (<u>keep scale/tool meltingpoints in mind</u>) with lots of dish soap.
                  • Put the SAK through a few cycles in the ultrasonic cleaner.

                  Dry SAK thoroughly to prevent it from attracting dust and dirt. And also to prevent staining.

                  Apply minimal appropriate lubriacation, I use either Victorinox Multitool Oil or Ballistol Oil.

                  It's a guarantied recipe to put the snap back in the SAK!

                  1 Reply Last reply
                  • Don Pablo Offline
                    Don Pablo
                    Posts: 15,329
                    Don Pablo Offline
                    Don Pablo
                    wrote on last edited by
                    #4 Quote Reply

                      @Mactire404 said:
                      This is how I do it:

                      SAK Cleaning

                      Getting rid of large particles

                      • Clean under running water with a brush, tools closed
                      • Clean under running water with a brush, tools open
                      • Open/close tools under running water

                      Getting rid of oils and small particles

                      • Place tool in a ultrasonic cleaner with properly warmed water (<u>keep scale/tool meltingpoints in mind</u>) with lots of dish soap.
                      • Put the SAK through a few cycles in the ultrasonic cleaner.

                      Dry SAK thoroughly to prevent it from attracting dust and dirt. And also to prevent staining.

                      Apply minimal appropriate lubriacation, I use either Victorinox Multitool Oil or Ballistol Oil.

                      It's a guarantied recipe to put the snap back in the SAK!

                      For the back tools, sometimes they can simply wear out the spring and tang, if they are of an old enough vintage. :-\

                      1 Reply Last reply
                      • Mactire404 Offline
                        Mactire404
                        Posts: 842
                        Mactire404 Offline
                        Mactire404
                        wrote on last edited by
                        #5 Quote Reply

                          @Pablo O'Brien said:
                          For the back tools, sometimes they can simply wear out the spring and tang, if they are of an old enough vintage. :-\

                          Unfortunately I don't have any SAKs old enough :-[

                          1 Reply Last reply
                          • Don Pablo Offline
                            Don Pablo
                            Posts: 15,329
                            Don Pablo Offline
                            Don Pablo
                            wrote on last edited by
                            #6 Quote Reply

                              @Mactire404 said:

                              @Pablo O'Brien said:

                              For the back tools, sometimes they can simply wear out the spring and tang, if they are of an old enough vintage. :-\

                              Unfortunately I don't have any SAKs old enough :-[

                              A friend found a climber small, and gave it to me. It seems to be from the 70's, and before I took it apart, the Corkscrew was sooo floppy, and the main and small blades had little tension. The culprit seems to be that the Corkscrew tang is slightly worn away, and the corresponding part of the spring also. :-\

                              1 Reply Last reply
                              • this_is_nascar Offline
                                this_is_nascar
                                Posts: 797
                                this_is_nascar Offline
                                this_is_nascar
                                wrote on last edited by
                                #7 Quote Reply

                                  Great info. Thanks everyone.

                                  Sent from my XT1635-01 using Tapatalk

                                  1 Reply Last reply
                                  • Mizedog Offline
                                    Mizedog
                                    Posts: 491
                                    Mizedog Offline
                                    Mizedog
                                    wrote on last edited by
                                    #8 Quote Reply

                                      In a pinch, I've used lip balm. What's nice about that is that you can go directly to pocket carry with no worry of leaking oil.

                                      Sent from my SAMSUNG-SM-N900A using Tapatalk

                                      1 Reply Last reply
                                      • NorCalJim Offline
                                        NorCalJim
                                        Posts: 1,544
                                        NorCalJim Offline
                                        NorCalJim
                                        wrote on last edited by
                                        #9 Quote Reply

                                          I go with Victorinox's own recommendation of cleaning. Unless there is a wear or alignment problem, cleaning nails it every time (at least it has for me). When purchasing off e-bay, I try to stick with SAKs in excellent condition. If I can see obvious dirt along with worn scales, I pop the scales for a thorough cleaning. If I plan to use the SAK, I want it in top condition and VERY clean. I open the tools and liberally coat it with dishwashing soap and place it along with any others getting this treatment in a bucket and submerse them in hot water to soak for 2 hours. After 2 hours, I start to clean them with brushes, pipe cleaners and running water. I finish up with a hair dryer before lubing the tools (less is more). I test the tools for snap and cleaning returns the snap unless there is a spring wear or an alignment problem. I then inspect the tools more carefully and if warranted, will proceed to my tool recondition process involving sanding with progressively finer automotive wet/dry sandpaper and polishing/buffing with my Dremel using a polishing wheel. Usually, one or both blades may have some scratches that can be removed with this process and the polishing leaves a mirror finish. My final step, if I have popped the scales, is to install new scales for a SAK that looks like new.

                                          Jim

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. Swiss Army Knights Forum
                                          4. Getting That "Snap" Back?
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0