Show me your drills
-
Absolutely, but when the hole is so small and is required to be a precise size, virtually any temperature variance will throw it out of calibration, which was the point.
Def
-
@Grant Lamontagne said:
Absolutely, but when the hole is so small and is required to be a precise size, virtually any temperature variance will throw it out of calibration, which was the point.Def
EDM drilling uses a continous fluid flow at high pressure which emits at the very end of the drill pipe. That provides electrical insulation and removal of the disharged material, and to the extend necessary also cooling. (Making a tiny 0,08mm diameter hole in a big chuck of metal doesn't necessarily add that much heat to begin with).
Similarly traditional drills for machining centers can be had with through drill flow for cooling and chip removal. (Example http://s3.cnccookbook.com/img/CNCCookbook/tsc-drill-bit.jpg). If really precise calibrated holes are needed then twisted drills are usually not precise enough anyway, and so need to be followed by other methods like reaming or boring.
A third option for minimizing heat using traditional drills is too simply go very slow but still with the correct pressure and cutting depth per rotation. I once saw a weird machine for doing exactly that. I have no idea what that was actually used for. (Well, doh, making holes..
).I have seen an old advert from around 1900 for a very portable mechanical contraption that did the same slow drilling. I'd actually like to have that one - would be a great portable solution for making controlled holes in stuff.
Talking about heat another offbeat drill method exploits exactly that. Flowdrilling will basically rotate and heat the material until it deforms into a hole with a suitable collar formed by the moved leftover material. Typically used for making threaded bolt connections in sheet metal.
I think the point I was trying to make was that there are often alternative technologies out there for many common problems, but which are rarely encountered or well known in the public.
-
There are just as many “types” of engineers as there types of personalities...
-
Some you should listen to, others you can ignore...YOU best pick the right one. And don’t assume they are all alike. Lol
-
Laser drilling...how about that.
-
Hyperthetically... if you had a steel object that had, for example, an exact 0.1mm diameter hole in it and it was exposed to "day to day" temp flux would that hole remain constantly 0.1mm in dia? Just curious.
-
@Fuzzbucket said:
Hyperthetically... if you had a steel object that had, for example, an exact 0.1mm diameter hole in it and it was exposed to "day to day" temp flux would that hole remain constantly 0.1mm in dia? Just curious.It would depend entirely on the type of steel...but what do I know? Hehe
-
Some alloys are recognized for their ability to remain somewhat stable under a wide range of temps...for example.
Anymore information about this topic will cost you. Oops my engineering background is creeping out.
-
Hyperthetically... if you had a steel object that had, for example, an exact 0.1mm diameter hole in it and it was exposed to "day to day" temp flux would that hole remain constantly 0.1mm in dia? Just curious.
It would depend entirely on the type of steel...but what do I know? Hehe
Yeah, ya dirty podgerphobe!!! ...(Just kidding!).
-
Hyperthetically... if you had a steel object that had, for example, an exact 0.1mm diameter hole in it and it was exposed to "day to day" temp flux would that hole remain constantly 0.1mm in dia? Just curious.
It would depend entirely on the type of steel...but what do I know? Hehe
Yeah, ya dirty podgerphobe!!! ...(Just kidding!).
I know Steve...me too...most of the time
-
@Marc_in_NS said:
Some alloys are recognized for their ability to remain somewhat stable under a wide range of temps...for example.Anymore information about this topic will cost you. Oops my engineering background is creeping out.
Your not a structural engineer by any chance? :D
-
Some alloys are recognized for their ability to remain somewhat stable under a wide range of temps...for example.
Anymore information about this topic will cost you. Oops my engineering background is creeping out.
Your not a structural engineer by any chance? :D
No, quite the opposite actually... I was combat systems engineering for a stretch. RCN
-
Some alloys are recognized for their ability to remain somewhat stable under a wide range of temps...for example.
Anymore information about this topic will cost you. Oops my engineering background is creeping out.
Your not a structural engineer by any chance? :D
No, quite the opposite actually... I was combat systems engineering for a stretch. RCN

-
Marc, you are absolutely correct that many engineers are not experts in rectal spelunking. The great thing about engineers though, is that it is almost immediately obvious which ones should be listened to, and which ones are going to be fun to play with. There's not a lot of middle ground! :D
Def
-
@Grant Lamontagne said:
Marc, you are absolutely correct that many engineers are not experts in rectal spelunking. The great thing about engineers though, is that it is almost immediately obvious which ones should be listened to, and which ones are going to be fun to play with. There's not a lot of middle ground! :DDef
So correct and, I suppose, one could say that about every trade/profession. “ the suit does not make the man”
-
Absolutely.
I was talking to a marine engineer a few years ago, and I swear when he produced a diagram he actually said (and I'm not making this up, although I wish I was) "Here, I drawed you a picture."
I've met some good ones too, just there are no good stories to tell about someone being competent! :D
Def
-
@Fuzzbucket said:
Talking of drilling holes and such like, I used these for the first time today - they were quite impressive.Alpen Multicut bits:
Masonry bits eh. What'd you drill?
-
Talking of drilling holes and such like, I used these for the first time today - they were quite impressive.
Alpen Multicut bits:
Masonry bits eh. What'd you drill?
Not just for masonary, they can go through wood and steel too. They're great at the moment... but for how long!?!
-
@Grant Lamontagne said:
Marc, you are absolutely correct that many engineers are not experts in rectal spelunking. The great thing about engineers though, is that it is almost immediately obvious which ones should be listened to, and which ones are going to be fun to play with. There's not a lot of middle ground! :D
Def
So correct and, I suppose, one could say that about every trade/profession. “ the suit does not make the man”
Very true, although I do find it interesting how some trades look down on other trades. Or how if you don't have a piece of paper with some letters on it but have 20+ years of experience, you are a nobody or know nothing. Just something I have notice over the years.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
