The Gerber MP1 Thread
-
I was replacing broken springs most of the day today so the MP1 didn't see much action. Did have time for a quick pic tho.

-
Used my MP1 to split and strip wire while replacing some safety eyes today. Used the prybar to pop the cover off this door opener and then used the larger flathead to adjust the travel limits.

Used the blade to cut open the packaging around a piece of replacement glass. Used the pliers to remove and reinstall the master link on the drive chain of a commercial door operator.
I'm really enjoying using the MP1 this week. So far I think my biggest complaint is the sprung pliers👎. I almost dropped it off the top of a 12 foot ladder today trying to balance it on there with a set of vice grips, a hammer and a wrench. Can't really just drop it in you pocket for a minute either or you'll spend the next 10 min trying to get back out.
-
I appreciate the info as I have been thinking about getting one.
Keep posting and I will keep reading.
-
I put my MP1 through a few trials I put all my new multitool EDC prospects through.
After peening the pliers pivot, to be clear.
I used the pliers to open the pipe plugs on a handful of 55 gallon drums of oil we had at work and to close the hydraulic cylinders on large jack stands.
This is about the most grueling test I could come up with to test resistance to torsional load (I've snapped pliers on 3 skeletools doing this as a note, and one wave pliers)
The mp1 withstood the sideload without gaining any slop.
Next I used the regular pliers section to hold onto a 20 x 2.5 stud while I ran a die down some bothered up thread.
Again no slop gained.
I then used the needlenose to place and remove .003 (width of a hair for reference) shims underneath some large steel weldments we needed to make fine leveling adjustments on.
I've used the bit driver on high feed milling cutters to back out torx insert screws. Without antiseize on the screws, it did twist a little but removed the screws. Have repeated that test multiple times on different sized cutters and screw sizes. All the way up to T30 torx screws in large diameter spade drills.
Used the pry tool and screwdrivers to shimmy out stuck collects and cutters. Which is a ton of torsional force on the pivots/tools
Maybe I got a good one, but If you can break the bit driver or pliers.
I'd like a video.
For me and my purposes as an EDC this is the "Wave" killer and I'll be sidelining my MUT, atleast for now.
-
All sounding very good gents.
Clown; I'm with you on sprung pliers though, the times they are a real advantage are hugely outweighed by the times they are a PITA. :-\ -
@Gareth said:
All sounding very good gents.
Clown; I'm with you on sprung pliers though, the times they are a real advantage are hugely outweighed by the times they are a PITA. :-\Agreed. Look much space this thing takes up.

I watched the pliers tips misalign themselves while twisting open this cotter pin. But they went back to normal.

I also noticed the handles 'squish' a little while squeezing hard on the pin to straighten it before reinstalling it. Nothing to cause worry as of yet though.
-
Those are the two things I was worried about as it is not a heavy looking tool.
Keep the info coming.
-
Been carrying the MP1 to work again this week. Ive been enjoying it. Especially the bit driver and the OH blade. It keeps me from having to carry a folder clipped to my pocket.
Three negative observations after about 8 days of use.
First, as reported by others, some rather noticeable slop has developed in the head. I guess I will have to try to peen the pivot.Second, there is a significant amount of handle flex when squeezing hard on the pliers. I noticed it today when trying to pull some small staples out of a 2x6. It seriously diminished the gripping force at the plier tips. That coupled with the tiny amount of ungrooved area the very tips of the pliers made it impossible for me to pull the staples out. At least the pointy needle nose tip was small enough to get under the staple so I could pry it out.
Third, as I expected, the tiny piece of Velcro used to hold the sheath closed is already starting to loose it's grippiness. I suspect in another couple if weeks it will quit grabbing altogether. Why manufacturers insist on using Velcro instead of a vastly more durable snap is beyond me.

To be continued....
-
Is the handle flex getting that bad? I found it disturbing at first, but it hasnt been issue while working with mp1?
I should send some extra velcro to Gerber as they might run low with their own stack. This pouch having 10mm x 10mm piece is ridicilous.

-
Shame to hear that the head has developed some play mate. :-\
-
I used a ball end peen (pictured)
The semi circle peen marks are a pin punch held up on edge so only part of the diameter is engaged.
Used a center punch to make a single punch in the lowest spot.
I can't twist them hard enough to get them to loosen up now.
Not pretty but effective.
The ball end peen is very effective at material displacement in the direction of force, but you could probably do it without one.
-
@Ravenroost said:
https://www.flickr.com/photos/158487066@N05/shares/XXe54EI used a ball end peen (pictured)
The semi circle peen marks are a pin punch held up on edge so only part of the diameter is engaged.
Used a center punch to make a single punch in the lowest spot.
I can't twist them hard enough to get them to loosen up now.
Not pretty but effective.
The ball end peen is very effective at material displacement in the direction of force, but you could probably do it without one.
Awesome. Thanks for the instructions!
-
Was thinking about getting one of these so wondered how they were holding up.
I like the idea of the "side cutter"pliers and the bit driver but not so sure on the spring action pliers!
I would appreciate any updates that would sway me one way or the other.......
Thanks.. -
@Jaypeebee said:
Was thinking about getting one of these so wondered how they were holding up.
I like the idea of the "side cutter"pliers and the bit driver but not so sure on the spring action pliers!
I would appreciate any updates that would sway me one way or the other.......
Thanks..While I do not use mine frequently, I did play around with mine and put them back on the shelf..
These are pretty my impressions rather than experience.
I am just going to talk mainly on the pliers, they seems rather "soft" to me. Twisting is def not something I would consider doing.. While the side cutters are a great idea, the sprung pliers pivot are built to a lesser tolerance. In long term use, I would think they will go misaligned faster than a cross over cutter. Making cutting a bit of challenge..
The rest of the tools are quite ok-ish.
-
Thanks Sam for the comments

I really need some heavy duty pliers so you might just have swayed me to the "nay" side :-\
-
@Jaypeebee said:
Thanks Sam for the comments
I really need some heavy duty pliers so you might just have swayed me to the "nay" side :-\
Hey but that my impression.. I didn't put it through much use. The earlier comments seems to praise it after using it. Someone with more hands on with it will have more input I am sure.
-
Then again, I am very biased against these type of anvil type cutters. I need mine to work with bare copper stranded wire. So they usually doesn't quite perform on this part.
Needs enlightenment. What's the different between a drop forged and cast pliers? Does it really makes so much of a difference?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
