Show off your Sak mod's!
-
-
Pabs! You didn't hang around! Nice job. How did it go?
-
I managed not to significantly damage the scales during the hammer time by sticking a strip of thick gorilla tape on each side. :)
Of course, that didn't matter very much since the scales came pre-abused(by you).
:PTerrible
preeningpeening, par for the course, but it seems that it will hold.
When I compared the size of the Alox bottle opener to the 91mm version, I went
holy censored, its that much beefier. :o
It brought to mind what Archimedes said about the alox bottle opener:
Give me the place to stand, and I shall move the earth -
It's an impressive tool isn't it?
via Imgflip Meme Generator -
@magentus said:
It's an impressive tool isn't it?
via Imgflip Meme GeneratorNo comment.

-
84mm & 91mm scientists.
The fluted corkscrew on the 84mm won't accept a screwdriver for some reason , So I'll swap that out when I can be arsed to get around to it.



-

But you'll excuse me if I don't give you a kiss.
:ahhh -
@Pablo O'Brien said:

But you'll excuse me if I don't give you a kiss.
:ahhhDamn dirty ape!
-
The orange peeler on an 74mm Executive is a great tool for peeling oranges, but otherwise? And an Executive doesn't have a bottle opener.
So I reground one to add beerability, and I thought that a pointy tool might be more useful than another sharp edge.
See some of my other SAK mods at https://sites.google.com/view/bobs-swiss-army-knife-mods/home
-
@Bob Wolfson said:
The orange peeler on an 74mm Executive is a great tool for peeling oranges, but otherwise? And an Executive doesn't have a bottle opener.So I reground one to add beerability, and I thought that a pointy tool might be more useful than another sharp edge.
See some of my other SAK mods at https://sites.google.com/view/bobs-swiss-army-knife-mods/home
Interesting prodder Bob...
It kind of reminnds me of the combo tool on the Golf Tool http://www.sakwiki.com/tiki-index.php?page=Golf+Tool
-
@Bob Wolfson said:
The orange peeler on an 74mm Executive is a great tool for peeling oranges, but otherwise? And an Executive doesn't have a bottle opener.
So I reground one to add beerability, and I thought that a pointy tool might be more useful than another sharp edge.
See some of my other SAK mods at https://sites.google.com/view/bobs-swiss-army-knife-mods/home
Interesting prodder Bob...
It kind of reminnds me of the combo tool on the Golf Tool http://www.sakwiki.com/tiki-index.php?page=Golf+Tool
@Bob Wolfson said:
The orange peeler on an 74mm Executive is a great tool for peeling oranges, but otherwise? And an Executive doesn't have a bottle opener.So I reground one to add beerability, and I thought that a pointy tool might be more useful than another sharp edge.
See some of my other SAK mods at https://sites.google.com/view/bobs-swiss-army-knife-mods/home
I like it. Does it have an edge to it or just the point/tip?
Sent from my XT1635-01 using Tapatalk
-
@this_is_nascar said:
I like it. Does it have an edge to it or just the point/tip?Sent from my XT1635-01 using Tapatalk
Just a point, at this point. I might add an eyelet for thread.
-
New Tinkertoy.
Inline awl from a 93mm knife, Thanks Mags
Dropped the backspring awl in favour of a backspring screwdriver.
I'll carry it for a week and see if this driver-centric build is to my liking or not. It looked good on paper, at least. Name tba.
-

I think MacGyver would carry that one!
-
FWIW, this is what the scissors/blades layer of a 74mm Executive looks like:
Note how the two springs interlock so only one end has to be pinned and the other 3 accept tools. The other layer, for the file and orange peeler, is just like in a 58mm knife, and is half as thick as this layer.
-
Cheers for the pic Bob.
I intend to make a 74mm jetsetter from a moneyclip and a file from a prince. This will be useful.
PS: interesting plate/jig in the background. I see you have holes for 74 and 58mm SAKs. Would you mind elaborating on it's purpose and use?
-
@T14 said:
Cheers for the pic Bob.
I intend to make a 74mm jetsetter from a moneyclip and a file from a prince. This will be useful.
PS: interesting plate/jig in the background. I see you have holes for 74 and 58mm SAKs. Would you mind elaborating on it's purpose and use?
I have been using a similar solution (but made of wood) to hold the pins in place when putting mods together. I can't answer if that is Bobs use for it but I imagine something along those lines. Made of metal it would allow for peening of the first side while holding it together.
-
@Fortytwo said:
I have been using a similar solution (but made of wood) to hold the pins in place when putting mods together. I can't answer if that is Bobs use for it but I imagine something along those lines. Made of metal it would allow for peening of the first side while holding it together.Yes, that's it exactly. I cut pins overly long and insert them in the 4 holes for whichever I'm assembling, either a 58 or 74. That holds them vertical and stable while I build the layers. The holes are actually very slightly oversize so the pins bind less when removing the assembled knife. I don't actually use them for peening because there's too much chance of causing that very binding. I just remove the assembled knife, grind down excess pin on both sides, and then bang away on the flat part of the plate (a barbell weight).
I also use the plate holes as a template for drilling holes in metal scales or liners. It's actually the first thing I do, even before shaping them. I cut the work shape roughly and mark where the holes are going to be. I then drill the hole 1 by eye. I pin the work to the plate at hole 1, and rotate it out of the way of hole 2 diagonally opposite, while I align hole 2 exactly with the bit in the press. I then rotate the work back into place by eye and drill through it, knowing the bit is dropping into hole 2 in the plate. Now I have two holes in the work exactly where they belong relative to each other, though they may not be exactly at the locations I originally marked. I can then align hole 3 in the plate with the bit in the press, rotate the work into place, pin it through holes 2 and 1, and drill 3. Etc. for #4.
Once I have 4 perfectly aligned holes in all my work pieces I pin them all together with an original side liner as a guide and start grinding away at the edges of the work pieces until they're flush with the liner. When I'm done, I have a mated set of pieces for polishing and assembly.
I'm maintaining a sort of blog of my results https://sites.google.com/view/bobs-swiss-army-knife-mods/home. No ads, for your enjoyment.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


