30D Traditional challenge
-
Day3
As promised here's a study in opening and closing. I imagine the best way to measure these knives would be to clamp both knife and blade then pull open using a spring scale. Since I don't have that kind of a setup available at the moment I will be simply pushing the knife shut from 90 degrees on a kitchen scale. This should produce similar results as the back spring applies equal force in either opening or closing. For consistency I will be aiming for the center dot on the scale, holding the blade roughly at where a nail Notch would be (some of them don't have it) and the reading is the highest that I catch by eye. This should be the hump point of the knife where it's most likely to either slip or snap your thumbnail.Rough Rider pliers 460g
Queen Cutlery Big Chief 930g
Rough Rider camper 1024g
SOG mini Auto clip 144
IK co 1040g
unknown Pakistan 370g
Victorinox Trekker 280gI've also included a close up of the nail notch on the screwdrivers of both the RoughRider camper and the Victorinox Trekker. As you can see the Trekker notch is cut a little bit deeper and at a sharp 90-degree on the inside edge. The RoughRider is a little shallower and you see the vertical scallops. The RR's top edge instead of being 90° like the Victorinox is polished slightly round making it harder to grip. If you press your thumb across both nail notches the fleshy part of your thumb will actually catch on the Victorinox but not on the Rough Rider indicating that high polish and the slickness inside the nail nick.
Edit:
Correction I just caliper the thickness of the nail nick on the Roughrider camper screwdriver and the Vic and they're both read the same. So I guess it's just the polish that makes the Rough Riders slicker


-
Over 1 kg? Does that mean the RR Camper is a nail breaker?
-
I would say yes. I have never broken a nail on it, but it is not a pleasent opener. You are more likley to slip and have it snap shut on you. The blade is actualy the easiest tool to open on the RR Camper if you can believe it. That awl is a nightmare.
It kind of reminds me of my first knife in that respect. I don't even remember where I got it, but somehow I ended up with this knife I could barely open when I was about 6 or 7. I had it for all of a day before my old man caught me with it and took it away.
Then he gave me an Imperial Camper HOBO. That knife was a better fit and I carried it every day and for Scouts till it was stolen at Custaloga Town when I was 12. I actually just "replaced" it ( nostalgia trip) last year with an Imperial Camper Matterhorn that I found at a local pawn shop. -
That is a lot of pressure :o :ahhh
-
Day 4
Can opener time
The RR Camper uses a blade style opener that many sellers mistake as a small blade with them stuff when listing it. Though this type is common on older knives and as an independent kitchen utensil; the only reference I've ever seen to this type that gives it a name calls it a "British tin opener"
Now this type of opener can really cut all the way around; usually you only end up cutting halfway Around the can and then pouring the contents. Also you can't punch it too close to the rim or else you'll punch through the side of the can.I will try to add that can opener chart as soon as I find it I'm not sure where I put the pic



-
Interesting about that style can opener :o

-
Day 5
This zip tie project is something I did at work about a year ago. (Pics however are new) The top shelf is 2 pieces of scrap shelving that I cinched togeather with zip ties, then lashed with 300# bank line. This has been done and 6 locations where the two small racks overlap.The boss was suposed to bolt them together and never did. It has held up suprisingly well. Average load on this is around 180#

-
Great fix
and great to see that it has held up 
-
Day6
Painting. I'm going to be moving to a new place at the end of January; so I'm trying to get a head start some things like putting the accent walls back to being white.

-
:ahhh How did I miss this.
good thread Noa Isumi
-
Good luck with painting
Hope that the move goes smoothly for you and that you get the place you are at now in tip top shape 
-
Day 6
Big Chief
Today we're taking a look at the QueenSteel #45 "BigChief". This is a large 4in blade single jack knife with a unique solid cast aluminum handle patented in the 1955(?). Because of this solid cast handle, the tail of the backspring passes through a cutout to catch onto the back of the handle allowing the pivot pin to be the only pin. This means the knife has a total of 4 pieces; handle, blade, backspring, pivot pin.
From what I understand these were produced at QueenCutlery of Titusville PA in the '60s & '70s. Queen is still in buisness producing small run, high quality traditionals.
This is one of the 2 Queens in my collection; the other bieng a fixed blade hunting knife (#82 I think). I heard they stopped making fixed blades in the early 90s, but never verified; so I could be wrong.



-
I haven't seen a queen like that in ages, very unique piece.

-
Very cool knife Noa 8)

-
Given how the Forum was down lets keep this rolling
Day7 kinda
It's a flashlight roundup.
In the middle you see pictured the RoughRider Pliers Electrician and around it you have three flashlights that I use on a daily basis.
On the one side we have the Streamlight protac 2L. This is a Gen2 280 Lumen (G1 was 180 &G3 is 360?) with two 123a lithium battery. This is my EDC light and is always on me.Next we have Ozark Trail 500 Lumen handheld spotlight powered by 3 C cells. This is my vehicle light; I use it for finding entryways in the dark and highlighting house, building and other road markings that are not always visible when I'm at work.
Lastly we have the Maglite LED 3D cell. This particular flashlight functions both as light and also it's what I tend to grab when I'm potentially not in a safe location and cant carry.
Sorry about the weird photo sizing. My camera automatically reset to its highest setting and I am using a new app to resize

-
Yes, we won't hold the forum being down against you :D
Carry on and great pic with lots of lights

-
Day8
Thats it. I'm done with this RRCamper knife.
Think thousand plus grams of force to open the main blade was nail breaker??? Well I just tried to do a nice photoshoot with the screwdriver & awl and managed to bust off both thumbnails. The secondary tools feel twice as tight as the main blade (which is tolerable once you're used to it). So now are you get is a rant. 
Say goodbye to it because I'll be using something else for the rest of the challenge and this will be going back in the knife trunk

-
:ahhh
Yes unfortunately some of the RR knives are nail breakers
Sorry it did that to your thumbnails Noa :o What knife will you be using now

-
Day 9
Ok. So I was cranky yesterday and took it out on my knife...whith good reason thoughSo today how about a roundup of what traditionals are left
Queen Big Chief
Case Sodbuster Jr (black handle, engraved)
Opnel no8
IK Co. (Steel & Green enamel)
RR Pliers
Milano (Philippine copy of a clasic Italian stiletto switchblade)
WASA souvenir knife ( Swedish made pen knife with three blades in an unequal lobster pattern)
4 unbranded Dime Store knives from the late 80s; Chinese made 2 wood handle, 1 blue pearlescent, 1 green plastic with metal flakeI know it won't be carrying the Chief, the Milano or the two plastic handle Dime stores. And we get enough Opnels around here there's no real point in doing that one.
I'm actually leaning towards the Sodbuster, I think.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
