30D Traditional challenge
-
Day 16
Today is not a Traditional folder like the Opnel in the pic, but rather that 1960s Sabatier chef's knife.This knife has been through alot of neglect in its life. The surface is pocked with rust, as such the edge is covered teeny tiny chips where it has eroded away, there even looks to be two 3/8 in stress cracks half way down. (or they may just be at stretches from rust) But for all its flaws this is one of best kitchen knives I have ever encountered. I wish I had more of this quality.
I really should just grind it back and reap profile it when the past the edge chipping but there's also some sentimental value to this one.
Pictured next to the master of modern infomercial... Ron Popeil Showtime six star.



-
Day17
Whats a page on the RR Pliers without looking at the pliers. In this case compaired next to Vic and Wenger pliers.
Overall they are similar enough and usefull. The Wenger bieng slip joint has the widest opening jaws but is so pollished it has the least agressive teath. The Vic has the most agressive bolt teeth and the smallest wire cutter notch. The RR is designed similar to the Vic but falls in the middle for teeth with an even 50/50 flat vs bolt surface, but is also has the smallest open spread.I was going to test them with some 18ga solid wire, but the Wenger was the only one that could even fit it in the cutter. This was suprising given the hole type cutter instead of a notch at the back of the jaws, and it cut quite well given it isnt sharp. The Wenger and Vic also have a v crimper; the Vic behind the jaw, the Wenger on the arm and spring lever.
Guest stars today are Victorinox Skipper and a late '90s Wenger Tradesman




-
Great pics and knives

-
Day18
It finally came in! It finally came in!
Figured I'd show off a new bit of Gun Leather I just got. I matched clearance discounts and bunch of store credit so in the end it cost me shipping. (and even part of that got covered by the credit)The harness fits great this thing is super comfortable when I tried it on.
Unfortunately that's also the downside is it's non-returnable and it doesn't fit my gun.

My gun is within the range of weapons listed for this particular holster. Unfortunately it stops a little over an inch shorter where it needs to be to seat properly. And to top it off this was a clearance non-returnable item.

Oh well, everyone ends up with a box in the bottom of their closet full of holsters that don't quite work for them; but that's not the fate of this one. My plan is to remove this one rivet and trim back the stitching right behind it, putting two new rivets at the top and bottom to anchor the stitching that I'm leaving behind. I may even restitch over it. This should open up the extra little bit of space in front of the strap grommet needed to accommodate the front of the trigger guard and allow it to seat properly.
Since I used to do harness work professionally this should hopefully be a simple task.
.

-
Day 19
I will have a knife on the rocks please.

-
Great pics Noa
Hope you get the harness issues fixed as well

-
Allready fixed it last night. Pulled the rivet and that curved line of stitching in front of the strap gromet and it fits fine now. Used superglue to anchor the last stich until I can get a couple new rivets.
-
I had to alter a IWB holster that was letting the gun sit to deep. A pop rivet fixed it right up.
Some day I'll stitch it so it looks better. -
Day20
Pulling staples from old catalogs/fliers to recycle the padges as packing material.
-
Day 21
Lunch time
-
Lunch looks good.

-
Day22
Whatsin the big, puffy mailer??

Christmas sweaters :ahhh
Yep I ordered Demolition Ranch Christmas sweatshirt for me and my wife....and a hat for me.
Check out the heavily armed Santa. No one I've shown the pick to seems to notice the green ball decorations are hand grenades


-
Day23

-
good pic


-
Day 24
Mail Call
I picked up the mail on my way to work tonight and what's in the Schrade box? It's a current production black oxide Schrade Tough Tool ST1NB. The BO coating on this feels more like a heavy tool enamel a comparison to the coating on my MP600, OHT, Kershaw folder. I would also like to add that it doesn't feel as "finished" as my old ST2. That aside it doesn't seem like it would be a bad basic starter ot beater tool and I certainly wouldn't scoff at it.

-
Day25
My pic just didnt work, but tiles of failed ones do. There's some from past stays at the bottom there too and don't ask me what the all black one is supposed to be.
-
Great pics from the ast few days

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
