Leatherman 2018 Rumors?
-
@gadgetman7 said:
I think it’ll be an evolution of the Skeletool/MUT/Signal that’ll replace the Wave. Or maybe a variation of the Signal. I really like the potential of that line.Sent from my iPad using Tapatalk
I think Skeletool, MUT, Signal platform will live on for a while of its own accord and not replace anything in particular. I could easily see the Signal die off, for reasons stated in my last post. Or maybe the MUT. Same reason in previous post. Skeletool will likely stick around, but I see most of that platform as paying more for less tool load out, and the other 3rd of that platform as just too expensive and specific.
-
Also, as point of fact, doesn't the best indicator of any future model come from either an inside source (scoop type news) or the US Patent office (solid plans)?
-
@ironraven said:
I'm still waiting on the slim line Rebar. Preferably a knifeless version with the saw and file. Or even super skinny, with pliers, drivers, openner/stripper, and no blades, no saw, no file.You do realise that the Rebar EDC has been out for a while?
Multi-Tool Without Knife | Rebar by Leatherman
Perfect for environments and job sites that need a handy set of tools, yet don’t allow for knife blades. Official Online Store of Leatherman.
Leatherman (www.leatherman.com)
-
I think it’ll be an evolution of the Skeletool/MUT/Signal that’ll replace the Wave. Or maybe a variation of the Signal. I really like the potential of that line.
Sent from my iPad using Tapatalk
Why would they replace the Wave at this stage?! With all due respect... That would be ridiculous. It is their best seller, hands down. I don't own a Wave, but I own a Surge, and see the appeal of a lighter Surge.
Skeletool = not enough tools for the price.
MUT = too speSmurfpillsed and expensive for John Q. Public
Signal = ...well, who the hell knows what Signal equals, but it ain't much compared to other less expansive tools with a much better load out like Surge and Wave or even Rebar for example.For the price of a Signal, I could buy a Rebar, and a Smith's sharpener, whistle, ferro combo and still have enough left over for two steak dinners. Make that two steak dinners with whiskey sours if we are talking about the REI Signal.
If you get over the plastic bits of the Signal, you can see that its the next gen of the Wave Frame.
Wave Frame (only one arm): 2 large tools, 3 small tools
Signal Frame (only one arm): 1 large tool, 4 small tools + room for a plastic implement
Signal Frame doubled up with 2 large tools (only one arm): 2 large tools, 5 small tools + room for a plastic implementYou can easily see, that the Signal frame has a much higher tool density. Whether you add the tap hammer on the second arm or not is then a matter of taste. Personally, I hope they offer both:
Signal 2A: 4 Large outside tools, 5 small tools + hammer + 2 plastic implements (bit holders would be great)
Signal 2B: 4 Large outside tools, 10 small tools + 2 plastic implements (bit holders would be great)All of this holds true, if they scale the Signal Frame up to Surge size.
-
I think the Wave is a great tool and have several including Charges. But, Leatherman has always evolved their tools and I suspect the Wave line will evolve too. It makes sense to merge the Signal/MUT line with the Wave line at some point but it’s likely that they’ll take elements from both.
I hope that Leatherman modifies the Signal myself. I’d like a Surge like blade exchanger to replace the saw and for them to add scissors. Also, remove the whistle and put in bit storage. Finally, just remove the outside file and upgrade the blade steel to S35VN. At that point you have a Wave minus the serrated blade but with a hammer, awl and locking handles.
Sent from my iPad using Tapatalk
-
Sorry about my ignorance but what is wrong with the pliers on the Wave or the Rebar???
Thank you. -
-
@Etherealicer said:
Signal 2A: 4 Large outside tools, 5 small tools + hammer + 2 plastic implements (bit holders would be great)That's the first thing I thought when I held the Signal for the first time. Be it the Wave set-up, or two blades + scissors + saw, or blade + scissors +saw + file, it would be sweet. Just adding two long tools would not make it too thick, and considering the negatives people list about the Signal, having four long tools would have helped it sell more.
@Etherealicer said:
Signal 2B: 4 Large outside tools, 10 small tools + 2 plastic implements (bit holders would be great)Another thought would indeed be pretty much a Wave with the plastic bits. The sharpener would be very easy to add, although it is not needed imo. If we also drop the whistle, the ferro rod could also be attached in the same manner as the sharpener.
The Wave is the problem, isn't it? It's just too good. All these bells and whistles, and some people still prefer the Wave over the Signal, even for the purpose the Signal was specifically designed to cater. Whenever a new full-size multitool is released, we can't help compare it to the Wave. If it is not just as good, then why not just go with a Wave?
In the Signal's case, dropping two long tools and making the blade combo edged had a lot to do with the mixed reviews it received.
I sincerely hope we see a new Signal Plus, with 4 long tools. Or maybe a Signal with a 154CM plain edge. And a sharpened awl.
Also, since the plastic bits are putting off lots of people, why not have them in aluminum instead? -
Signal 2B: 4 Large outside tools, 10 small tools + 2 plastic implements (bit holders would be great)
Another thought would indeed be pretty much a Wave with the plastic bits.{...}
No, it has 4 small tools more, (check out where the awl on the Signal is!!!). And because they are in the same slot as the large tools, they can be rather thick.
-
Signal 2B: 4 Large outside tools, 10 small tools + 2 plastic implements (bit holders would be great)
Another thought would indeed be pretty much a Wave with the plastic bits.{...}
No, it has 4 small tools more, (check out where the awl on the Signal is!!!). And because they are in the same slot as the large tools, they can be rather thick.
10 small tools is pushing it I think. As it is, the default Signal has three small tools. awl, can opener, and the bit holder which is thick so let's say it takes two spaces. We could have four tools in the opposite handle. Maybe.The Wave would have three: small bit holder, large flathead, scissors.
Maybe both blades could have a tool resting in their gap, like the awl does now, but what other short implements could do that with the saw, file, or scissors?
-
Signal 2B: 4 Large outside tools, 10 small tools + 2 plastic implements (bit holders would be great)
Another thought would indeed be pretty much a Wave with the plastic bits.{...}
No, it has 4 small tools more, (check out where the awl on the Signal is!!!). And because they are in the same slot as the large tools, they can be rather thick.
10 small tools is pushing it I think. As it is, the default Signal has three small tools. awl, can opener, and the bit holder which is thick so let's say it takes two spaces. We could have four tools in the opposite handle. Maybe.The Wave would have three: small bit holder, large flathead, scissors.
Maybe both blades could have a tool resting in their gap, like the awl does now, but what other short implements could do that with the saw, file, or scissors?
A Phillips, flat drivers would work. With the Signal, the awl is in the blade layer, so there would certainly be enough space in the saw/file layer... quite frankly you could probably design a small bit holder (for the eye-glass bit) to fit there as well or just a long needle.
-
@Etherealicer said:
A Phillips, flat drivers would work. With the Signal, the awl is in the blade layer, so there would certainly be enough space in the saw/file layer... quite frankly you could probably design a small bit holder (for the eye-glass bit) to fit there as well or just a long needle.If we had two blades, one could have the awl, like the default Signal does, and the other could have something else. It would be a serrated blade, so it would be chisel-ground anyway. A flathead could go there.
In the Signal now, the awl sits next to the blade, in the gap its grind leaves. The saw and file would not allow other tools to rest next to them like that.
If we're talking just having implements opposite the saw and file, like the OHT, that would not go well. I'd rather have a longer saw that occupies the whole length of the handle. -
A Phillips, flat drivers would work. With the Signal, the awl is in the blade layer, so there would certainly be enough space in the saw/file layer... quite frankly you could probably design a small bit holder (for the eye-glass bit) to fit there as well or just a long needle.
If we had two blades, one could have the awl, like the default Signal does, and the other could have something else. It would be a serrated blade, so it would be chisel-ground anyway. A flathead could go there.
In the Signal now, the awl sits next to the blade, in the gap its grind leaves. The saw and file would not allow other tools to rest next to them like that.
If we're talking just having implements opposite the saw and file, like the OHT, that would not go well. I'd rather have a longer saw that occupies the whole length of the handle.Maybe you are right (meaning one would have to put both blades on the non-hammer arm). However, my quick mock up (moving the saw to the blade-layer) shows there is quite a bit of room, depending on where you stop the saw.
You could for example have a thin hand drill there... or simply a needle.

-
A Phillips, flat drivers would work. With the Signal, the awl is in the blade layer, so there would certainly be enough space in the saw/file layer... quite frankly you could probably design a small bit holder (for the eye-glass bit) to fit there as well or just a long needle.
If we had two blades, one could have the awl, like the default Signal does, and the other could have something else. It would be a serrated blade, so it would be chisel-ground anyway. A flathead could go there.
In the Signal now, the awl sits next to the blade, in the gap its grind leaves. The saw and file would not allow other tools to rest next to them like that.
If we're talking just having implements opposite the saw and file, like the OHT, that would not go well. I'd rather have a longer saw that occupies the whole length of the handle.Maybe you are right (meaning one would have to put both blades on the non-hammer arm). However, my quick mock up (moving the saw to the blade-layer) shows there is quite a bit of room, depending on where you stop the saw.
You could for example have a thin hand drill there... or simply a needle.
Another idea would be a thin round file... you could have it several cm long, great to quickly clean out a hole.
-
I would actually like to see them improve the Wingman/Sidekick format. This tool is very useful in the real world with a good design basis to make it even better. They could do 4 outside tools, they could improve the pliers for better cutting, refine the scissor, they could even go locking in the future for the inner tools. It seems they went mostly in the wrong direction with the Rev, who's to say they won't improve one of their most popular and well reviewed product lines in the future.
-
I’d like a bladeless Juice. Remove the Philip’s screwdriver and put in a bit holder. Remove a couple of the small flat head screwdrivers and put in Wave scissors. Also, just remove the outside tools and make it TSA/no knife areas friendly. Just dreaming though...
Sent from my iPad using Tapatalk
-
Have the wire cutters on the skeletool a millimetre or two longer, because right now they're just too short to cut standard zip ties
-
@Etherealicer said:
Maybe you are right (meaning one would have to put both blades on the non-hammer arm). However, my quick mock up (moving the saw to the blade-layer) shows there is quite a bit of room, depending on where you stop the saw.You could for example have a thin hand drill there... or simply a needle.
Certainly something could fit in there. Even just a needle would be a nice use of space. Victorinox does it with reamers and blades. Why not a small serrated blade? Like on the Sidekick or the Boker tech tools. Maybe even tweezers.

-
Wave gen III: drop the scissor outside, the file inside, add an awl and a pair of tweezers. A bit restyling and we have the new Wave without changing it radically!
-
@tango44 said:
Sorry about my ignorance but what is wrong with the pliers on the Wave or the Rebar???
Thank you.Nothing wrong with them at all. Some, like me, love the new style plier head on the Rebar and hopes to see the Wave get this upgrade. Other love the old style or current style plier heads on the Wave. I can't blame them because it have worked for years with no problems and cuts wire fine. I like the new style because I cut a lot of wire and have worn out the cutters on my multitools and it is nice just to drop in new cutters instead of buying a new tool of finding a plier head to install.
Personally I wish LM would quit trying to make new stuff for awhile and just focus on there top heavy hitters. Just make them better here and there.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login