Home solution for loose pliers pivot! Experiment!
-
@Syncop8r said:
If turning one way tightens the plier heads.... is anyone willing to go the other way to see if they can disassemble them?
I would be interested to see them apart.I seriously do not think they are screw on. It could be the surface between the dead side are somewhat sloped or at a very slight angle. Turning the whole pivot simply close up the gap or widen it. There no way to unscrew the pivot in the manner we are discussing here as we are turning both side together.
-
I've tightened a few in the past by laying the plier head flat on my anvil and tapping off centre with my peening hammer,worked both times with little noticable damage

-
@Sam Lim said:
If turning one way tightens the plier heads.... is anyone willing to go the other way to see if they can disassemble them?

I would be interested to see them apart.I seriously do not think they are screw on. It could be the surface between the dead side are somewhat sloped or at a very slight angle. Turning the whole pivot simply close up the gap or widen it. There no way to unscrew the pivot in the manner we are discussing here as we are turning both side together.
Beg to differ... the pivot could go all the way through and have screw thread matching some on one of the plier halves...
Sent on my SM-G930F with Tapatalk
-
Only one way to find out...

-
@Sam Lim said:
If turning one way tightens the plier heads.... is anyone willing to go the other way to see if they can disassemble them?

I would be interested to see them apart.I seriously do not think they are screw on. It could be the surface between the dead side are somewhat sloped or at a very slight angle. Turning the whole pivot simply close up the gap or widen it. There no way to unscrew the pivot in the manner we are discussing here as we are turning both side together.
Beg to differ... the pivot could go all the way through and have screw thread matching some on one of the plier halves...
Sent on my SM-G930F with Tapatalk
Not quite agree.. As I mentioned when we turn the pivot, both side turns at the same rate. So there is no unscrewing of anything.
-
@Mechanickal said:
Loose plier heads?! What the...Oh! I see!
I stumbled in the Leatherman section here! >:D

Great find though...
I forgot to mention I had tried this on my Gerbers, worked on none of them..

:D
-
@Sam Lim said:
@Sam Lim said:
If turning one way tightens the plier heads.... is anyone willing to go the other way to see if they can disassemble them?

I would be interested to see them apart.I seriously do not think they are screw on. It could be the surface between the dead side are somewhat sloped or at a very slight angle. Turning the whole pivot simply close up the gap or widen it. There no way to unscrew the pivot in the manner we are discussing here as we are turning both side together.
Beg to differ... the pivot could go all the way through and have screw thread matching some on one of the plier halves...
Sent on my SM-G930F with Tapatalk
Not quite agree.. As I mentioned when we turn the pivot, both side turns at the same rate. So there is no unscrewing of anything.
Hmmm... both pivot ends turning at the same time strongly suggests it is one piece (somewhat against my expectations), or maybe two pieces with a snap fit or screwed together very tightly. Tightening when turning one way (presumably clockwise?) kind of suggests (more) screw thread, but you're right, circumferentially sloping surfaces could also work...

I have a PST with a minute wiggle in the pliers. I'll see if I can find out once I'm back home from skiing (see outdoors thread :D).
Sent on my SM-G930F with Tapatalk
-
@Sam Lim said:
Loose plier heads?! What the...
Oh! I see!
I stumbled in the Leatherman section here! >:D

Great find though...
I forgot to mention I had tried this on my Gerbers, worked on none of them..

:D
What about SwissTools? Oh that's right, they don't develop plier play or any other problems because they are swiss.

-
@Pablo O'Brien said:
@Sam Lim said:
Loose plier heads?! What the...
Oh! I see!
I stumbled in the Leatherman section here! >:D

Great find though...
I forgot to mention I had tried this on my Gerbers, worked on none of them..

:D
What about SwissTools? Oh that's right, they don't develop plier play or any other problems because they are swiss.

Steal someone else's joke

-
@Pablo O'Brien said:
@Sam Lim said:
Loose plier heads?! What the...
Oh! I see!
I stumbled in the Leatherman section here! >:D

Great find though...
I forgot to mention I had tried this on my Gerbers, worked on none of them..

:D
What about SwissTools? Oh that's right, they don't develop plier play or any other problems because they are swiss.

Steal someone else's joke

:D
-
@Pablo O'Brien said:
@Sam Lim said:
Loose plier heads?! What the...
Oh! I see!
I stumbled in the Leatherman section here! >:D

Great find though...
I forgot to mention I had tried this on my Gerbers, worked on none of them..

:D
What about SwissTools? Oh that's right, they don't develop plier play or any other problems because they are swiss.

I, am a electrical technician by trade. I need my cutters to cut soft copper cable.. They simply does not cut well.. I didn't think tightening them would make any difference....


-
@Sam Lim said:
@Sam Lim said:
[quote author=Syncop8r link=topic=75195.msg1607136#msg1607136 date=1514361932]
If turning one way tightens the plier heads.... is anyone willing to go the other way to see if they can disassemble them?
I would be interested to see them apart.I seriously do not think they are screw on. It could be the surface between the dead side are somewhat sloped or at a very slight angle. Turning the whole pivot simply close up the gap or widen it. There no way to unscrew the pivot in the manner we are discussing here as we are turning both side together.
Beg to differ... the pivot could go all the way through and have screw thread matching some on one of the plier halves...
Sent on my SM-G930F with Tapatalk
Not quite agree.. As I mentioned when we turn the pivot, both side turns at the same rate. So there is no unscrewing of anything.
Hmmm... both pivot ends turning at the same time strongly suggests it is one piece (somewhat against my expectations), or maybe two pieces with a snap fit or screwed together very tightly. Tightening when turning one way (presumably clockwise?) kind of suggests (more) screw thread, but you're right, circumferentially sloping surfaces could also work...

I have a PST with a minute wiggle in the pliers. I'll see if I can find out once I'm back home from skiing (see outdoors thread :D).
Sent on my SM-G930F with Tapatalk
[/quote]Today, I tried on a plier that was really loose. Probably beyond repair. I did the same method again. I did dial it to a certain extent it was tighter but any more, it would "pop" loose again. So the, "circumferentially sloping surfaces" should be at work. Intentionly or not by leatherman, it's brilliant.
-
@Sam Lim said:
As I mentioned when we turn the pivot, both side turns at the same rate. So there is no unscrewing of anything.So if you were to mark the other side (the one that moves) say, when the pliers are fully closed (as a reference) you should see the line move after adjustment?
Yes. That's moves also.
-
@Sam Lim said:
@Sam Lim said:
[quote author=Sam Lim link=topic=75195.msg1607150#msg1607150 date=1514364506]
[quote author=Syncop8r link=topic=75195.msg1607136#msg1607136 date=1514361932]
If turning one way tightens the plier heads.... is anyone willing to go the other way to see if they can disassemble them?
I would be interested to see them apart.I seriously do not think they are screw on. It could be the surface between the dead side are somewhat sloped or at a very slight angle. Turning the whole pivot simply close up the gap or widen it. There no way to unscrew the pivot in the manner we are discussing here as we are turning both side together.
Beg to differ... the pivot could go all the way through and have screw thread matching some on one of the plier halves...
Sent on my SM-G930F with Tapatalk
Not quite agree.. As I mentioned when we turn the pivot, both side turns at the same rate. So there is no unscrewing of anything.
Hmmm... both pivot ends turning at the same time strongly suggests it is one piece (somewhat against my expectations), or maybe two pieces with a snap fit or screwed together very tightly. Tightening when turning one way (presumably clockwise?) kind of suggests (more) screw thread, but you're right, circumferentially sloping surfaces could also work...

I have a PST with a minute wiggle in the pliers. I'll see if I can find out once I'm back home from skiing (see outdoors thread :D).
Sent on my SM-G930F with Tapatalk
[/quote]Today, I tried on a plier that was really loose. Probably beyond repair. I did the same method again. I did dial it to a certain extent it was tighter but any more, it would "pop" loose again. So the, "circumferentially sloping surfaces" should be at work. Intentionly or not by leatherman, it's brilliant.
[/quote]Ah thanks, no screw thread then
Sent on my SM-G930F with Tapatalk
-
I think the mechanics of this are simple. As the pliers get used the pivot which is round gets slightly oval in shape and pliers loosen. When we turn the pivot the oval fills the round hole a bit effectively tightening the pivot again.
-
I concur with the above hypothesis.
-
I too think that is the possible reason. The sloping theory is just too complicated to implement. What the heck, so how many have been fixed? ☺️
-
Whatever the reason, this seems like a pretty brilliant bit of information. Good work, Sam Lim!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login