Robertson bits
-
If I look around my home at some of my furniture, the underside of my computer chair, and also looking inside my shop at various items it's amazing how many have been assembled using a Robertson headed screw.
Compared to the Flat Head or the Phillips isn't it always a relief when you take something apart or perhaps are building to use the Robertson? It slips less than the flat and phillips and doesn't strip out the head of the screw as easily when stubborn.
My question is why do we not see Robertson heads on multi-tools or as a bit accessory? I bought the Victorinox Spirit Tool and the Zilla Jr. and neither of them came stock with any Robertson bits. I did add a couple of these bits to the Victorinox caddy to make it complete. Any thoughts?sean
-
SOG does have Robertson drives :)
and the leatherman bit pack has a couple of robertsons too, if my memory doesnt fail me
-
Robertsons are a Canadian thing, and manufacturers don't specifically target Canadians when they make tools. Most of the rest f the world wouldn't have a clue what that square thing was, and figure they got gipped because they are missing an adaptor or something
SOG has a Robertson bit available to swap into their tools, and Leatherman offers a few Robertsons with the bit sets found on Charges and other models as well as available by themselves. That's one of the reasons why I also favor multitools that accept standard 1/4" hex bits- I can buy a screwdriver set for a few dollars at Canadian Tire and always have the bits I need. Robertson and Torx are the ones I am always looking for, but are rare in the multitool world, probably because of the lack of versatility. Those are the ones where you need the right size, or it won't work. With phillips and flatheads, anything that fits in will work well enough in a pinch.
Def
-
@Defender said:
Robertsons are a Canadian thing, and manufacturers don't specifically target Canadians when they make tools. Most of the rest f the world wouldn't have a clue what that square thing was, and figure they got gipped because they are missing an adaptor or somethingSOG has a Robertson bit available to swap into their tools, and Leatherman offers a few Robertsons with the bit sets found on Charges and other models as well as available by themselves. That's one of the reasons why I also favor multitools that accept standard 1/4" hex bits- I can buy a screwdriver set for a few dollars at Canadian Tire and always have the bits I need. Robertson and Torx are the ones I am always looking for, but are rare in the multitool world, probably because of the lack of versatility. Those are the ones where you need the right size, or it won't work. With phillips and flatheads, anything that fits in will work well enough in a pinch.
Def
Interesting thanks for the insight. I wouldn't mind having a few extra style bits for my Zilla Jr. I didn't realize that the Robertson was primarily Canadian. It's a great head.
sean
-
Like Def said, over here Robertsons are very uncommon. I have encountered them, but I certainly would not see the need to EDC a Robertson bit.
-
Good luck finding extra bits for the Zilla Jr. When they designed the Jr and the Li'l Guppie, they scaled everything down by (I think) 14%, including the bit drivers, which meant they also needed smaller bits. Since they aren't standard sizes, you may not be able to find replacements.
Def
-
When I bought my skeletool I found Leatherman included an extra flat Robertson bit for Canadian models, which I think is a very good gesture, it even saved my butt once.
-
That's what I get for having goten mine in the US... ::)
Def
-
With the money you saved you could've bought the whole set. :P
-
I have numerous sets already, with my many Charges!
Def
-
Am I dreaming or did someone here really come up with a brilliant idea of grinding/filing the sides of a flat screwdriver head to fit into the square recess (Robertson) diagonally?
-
I ran into squares a lot when doing electric work... most electric panels, breakers, and outlets/switches/etc. have screws that you can use a straight, square, or phillips (or some combination of them). Personally, I love the squares and used them whenever possible.

-
One thing about grinding straights down to squares would be that you really do need a HARD tip on a square, or it will just round off and become a circle, which is good for nothing.
-
@NeitherExtreme said:
One thing about grinding straights down to squares would be that you really do need a HARD tip on a square, or it will just round off and become a circle, which is good for nothing.Ahh, you are referring to the Stripdout series of fasteners. I have these in various places around my house. Usually at least one screw in every device I attempt to work on is a stripdout. Typically it is the last one. I think this is done for security reasons.
-
I like Robertson screws better than Phillips, too bad they never caught on outside of Canada.
-
One thing about grinding straights down to squares would be that you really do need a HARD tip on a square, or it will just round off and become a circle, which is good for nothing.
Ahh, you are referring to the Stripdout series of fasteners. I have these in various places around my house. Usually at least one screw in every device I attempt to work on is a stripdout. Typically it is the last one. I think this is done for security reasons.
hehe, I've run into my share of those too... But what I was saying was that I think the steel used in MT screwdrivers would be too soft to make a good Robertson. :-\
-
One thing about grinding straights down to squares would be that you really do need a HARD tip on a square, or it will just round off and become a circle, which is good for nothing.
Ahh, you are referring to the Stripdout series of fasteners. I have these in various places around my house. Usually at least one screw in every device I attempt to work on is a stripdout. Typically it is the last one. I think this is done for security reasons.
hehe, I've run into my share of those too... But what I was saying was that I think the steel used in MT screwdrivers would be too soft to make a good Robertson. :-\
Too soft to make a good Robertson out of a flathead? I agree.

-
torx > hex > robertson > philips > flat
IMHO anyway.
-Dough
-
Sean the Old Skool Leatherman universal tool adapter will work with your Spirit , it uses 1/4hex bits . There were two versions , one made for the Supertool and one for the other Leatherman tools . The Supertool version has a prong on it ( easily ground off ). Build quality was superb , they would take three positions , 45 and 90 degrees and straight . You should readily find one on evil bay .
Chris
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login