And so it begins.... (My adventures into Alox!)
-
Is brass strong enough to hold the screws?
Sent from my iPad using Tapatalk
-
Brass should be fine. I've made around a dozen sets of brass pivots for SAKs by drilling 3mm rod (in a lathe - I need to try shibafu's method) and not broken one yet. Make sure the screws are as long as possible so as to give the brass tube maximum support. If you were to really crank down on the screws it'd be about evens as to whether the brass thread stripped or you rounded out the screw head.
I've only found 3mm stainless tube in 316 grade which is no good for pivots. You want 400 series so it can be heat treated or 301/302/304 in spring temper - which are only available in rod/wire. The properties that make a grade of stainless suitable for drawing into a tube make it unsuitable as a bearing.
-
Oh, and I think the grade of brass I've used is half-hard CZ121.
-
OK, thanks again

It'll be a while until I have all the bits but once I get going I
mightwill post progress reports and results. -
Syph, since you are making custom Ti tools, would it be possible to make a chisel/scraper like the Spirit to fit a 91/93mm? Also wondering about how the edge would hold up.
-
Syph, since you are making custom Ti tools, would it be possible to make a chisel/scraper like the Spirit to fit a 91/93mm? Also wondering about how the edge would hold up.
depends on what you want to scrape

The edge would be durable, but in now way be able to retain a shaving sharp edge or anything. it would quickly round over and pretty much stay that way.
-
@Syph007 said:
The edge would be durable, but in now way be able to retain a shaving sharp edge or anything. it would quickly round over and pretty much stay that way.+1
I use a small 'sharp' Ti piece to open boxes, works perfect to perforate tape. But it can't be razor sharp (which is perfect to open things without opening a finger in the way
) -
The edge would be durable, but in now way be able to retain a shaving sharp edge or anything. it would quickly round over and pretty much stay that way.
+1
I use a small 'sharp' Ti piece to open boxes, works perfect to perforate tape. But it can't be razor sharp (which is perfect to open things without opening a finger in the way
)A chisel edge can have the back flat part carbidized though to try to maintain somewhat of an edge. The soft Ti is worn away leaving a sharp edge just like how a beaver tooth stays sharp. I've never tested this but in told it works.
-
I’m assuming you’re not going to be using a hammer on the opposite end of the chisel?
-
Boyscout explorer with Fleur-de-lis. :D
-
Very nicely done the boyscout logo

-
:o
-
:like this a lot!!!
-
I hope that lucky scout can realize what a piece that is.

-
@ReamerPunch said:
I hope that lucky scout can realize what a piece that is.
I'm a scout, can I have it?

-
I like the Fleur de Lis, reminds me of Firenze.

-
After 1.5 years of constant running my Tormach had an issue today. Spindle wouldn't start up and the main controller was thowing a hardware fault. I called support and had help in about 30 minutes. They determined I needed a new controller part (approx $400-500 ish) since im past the year warranty. However they decided to send me one for free since they said it must be a hardware issue and not something Id done to the controller so they are sending me a free one as long as I send them the broken one back for analysis. I can't complain about that service! This is why you buy a machine from a company that will still be around in a year to help you.

Compact super tinker today. Still a very popular model.
-
You are a fortunate man Syph. There are quite a few vendors who would not have been so generous, I gather...
Nice knife

-
Gorgeous knife!!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login