Need some advice on etching!
-
Or should I just leave it and have a story to tell whenever someone ask me about it.. Seriously I dun mind it there.. Just prefers it be clean....
-
So first the previous owner covered up these messages, and then he sold the knife? I wonder how that relationsship is going.
Now if I'm to say something actually useful I might suggest that these probably custom one-off messages were done with a laser. Electro chemical marking is an alternative, but a bit more hassle to make one-offs and needs acid treatment and what not afterwards when used on stainless steel. So I'm going with laser.
The mark is probably not very deep. The aim was probably just to get rid of the black treatment in those areas. So my guess is that if you remove the black treatment you get rid of the messages too.
Might I suggest to just strike over the first name and add a name of your choice after? I'm so romantic! :D
-
Or you could change your name (and perhaps your partner's) to match what is on the blade. :D
-
Sort of saw the name changing thing coming.... I am going to attempt sanding it once more.
-
If you just want to get rid of all the black, with that the text contrast, then that is likely easiest to do chemically.
If you go this way then getting the black on again will be the main issue. I've never tried, but there seems to be a big gap in quality between the industrial methods and the home small scale ones.
Edit: That might actually explain your sudden secret text? It might have been covered up with some DIY black oxide method which was less acid proof than the factory version.
-
@Vidar said:
If you just want to get rid of all the black, with that the text contrast, then that is likely easiest to do chemically.If you go this way then getting the black on again will be the main issue. I've never tried, but there seems to be a big gap in quality between the industrial methods and the home small scale ones.
Edit: That might actually explain your sudden secret text? It might have been covered up with some DIY black oxide method which was less acid proof than the factory version.
Oh wait. I think you got it the other way round. It was originally a badly scratched up ss blade. I used ferric chloride to etch the whole blade. The text was not noticed before. I did the black. So somehow now the text part was not affected by the acid. After my first try, the text now pops out more than the blade surface..
I am trying to sand down the whole blade now.. It doesn't help when it's a little hollow grind on the back... I only have my sandpaper, fingers and a file..... The 154cm is resisting my elbow grease..... -
If anyone asks, you told the sobbing young lady you'd take care of the mess, gave the handle a mighty twist, then pulled it from his heart where she left it. Because he was a cad. And he deserved it.
If this was laser etched, sandpaper will probably be your best bet. You might just have to take off a few thousands of an inch of metal to get rid of it. Slowly, so not to trash the temper. Scrub for a minute, check it. Over and over and over....
Cover story, becuase life is short. And who doesn't like a good story.
-
@Sam Lim said:
Oh wait. I think you got it the other way round. It was originally a badly scratched up ss blade. I used ferric chloride to etch the whole blade. The text was not noticed before. I did the black. So somehow now the text part was not affected by the acid. After my first try, the text now pops out more than the blade surface..
I am trying to sand down the whole blade now.. It doesn't help when it's a little hollow grind on the back... I only have my sandpaper, fingers and a file..... The 154cm is resisting my elbow grease.....Ah, that does sound like the way around. You didn't say you did the black so I thought it started out like that. Well, then sanding should offer some hope.
@ironraven said:
If anyone asks, you told the sobbing young lady you'd take care of the mess, gave the handle a mighty twist, then pulled it from his heart where she left it. Because he was a cad. And he deserved it.I thought young ladies broke hearts, not stabbed them? Times are changing I guess.
-
@Sam Lim said:
Oh wait. I think you got it the other way round. It was originally a badly scratched up ss blade. I used ferric chloride to etch the whole blade. The text was not noticed before. I did the black. So somehow now the text part was not affected by the acid. After my first try, the text now pops out more than the blade surface..
I am trying to sand down the whole blade now.. It doesn't help when it's a little hollow grind on the back... I only have my sandpaper, fingers and a file..... The 154cm is resisting my elbow grease.....Ah, that does sound like the way around. You didn't say you did the black so I thought it started out like that. Well, then sanding should offer some hope.
@ironraven said:
If anyone asks, you told the sobbing young lady you'd take care of the mess, gave the handle a mighty twist, then pulled it from his heart where she left it. Because he was a cad. And he deserved it.I thought young ladies broke hearts, not stabbed them? Times are changing I guess.
Ironically, from the names I have censored, it seems it was a gift from a guy to a lady...
-
Elbow grease wins. Now working on the serration..

-
Completed. Giving myself a little pat on the back. From scratched up blade, to blade with a story, to this. Added a little stone wash look to it. :D

-
Looking good!

If only that worked on tattoos too ::)
-
that turned out really nice

-
-
If only that worked on tattoos too ::)
A power sander should take care of a tattoo....

Not sure if a power sander would fit...

Edit: Don't blame me for your visualizations...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



