And so it begins.... (My adventures into Alox!)
-
@Dutch_Tooler said:

Nice subdued, almost stealthy look with those grey liners. How were these made - anodised?PS did the repairs go well?
Tumbled in cermics makes Ti go dark like that. Really durable finish too since it surface hardens the Ti.
It was only a 10 minute job to swap in the new controller part and I was back up and running. It must be a newer model as it has better control than the old one. When I turned off the spindle before it would free spin for about a half minute but now it stops almost immediately. Probably a safety upgrade.
-
Thanks on both counts, Syph

Ti liners too, I take it... wow...

-
@Dutch_Tooler said:
Thanks on both counts, Syph
Ti liners too, I take it... wow...

Yep Ti liners. This one is heading over to Thailand! I like shipping saks all over the place. :D I wish I would have kept a map showing each location Ive shipped to in the last 6 yrs. Every continent except Antarctica.
-

Nice subdued, almost stealthy look with those grey liners. How were these made - anodised?PS did the repairs go well?
Tumbled in cermics makes Ti go dark like that. Really durable finish too since it surface hardens the Ti.
It was only a 10 minute job to swap in the new controller part and I was back up and running. It must be a newer model as it has better control than the old one. When I turned off the spindle before it would free spin for about a half minute but now it stops almost immediately. Probably a safety upgrade.
I had thought you were only doing sandblasting, due to the time it took to tumble. ???
Sorry for the wrong info Dutch_Tooler! :P
-
That is one sexy knife, Syph.
-

Nice subdued, almost stealthy look with those grey liners. How were these made - anodised?PS did the repairs go well?
Tumbled in cermics makes Ti go dark like that. Really durable finish too since it surface hardens the Ti.
It was only a 10 minute job to swap in the new controller part and I was back up and running. It must be a newer model as it has better control than the old one. When I turned off the spindle before it would free spin for about a half minute but now it stops almost immediately. Probably a safety upgrade.
I had thought you were only doing sandblasting, due to the time it took to tumble. ???
Sorry for the wrong info Dutch_Tooler! :P
No worries WWW 8)
-
I did a new mod today... no really I did and it was on a 93mm
Customers asked if I can put a mag glass in place of can opener. I said nope its too wide... then I thought well the glass part isnt as wide as the tool...hmmm could I make a smaller brass mag holder to work? Turns out yes. Only caveat is that i had to put that layer in the middle so the nicks were accessible but since the can opener is banished that layer didnt need to be on the outer edge any longer.
-
Couple more.
Now what to call a pioneer x with magnifier in place of can opener? Not really an explorer variant since it has no phillips. So maybe the Pioneer Sleuth?
-
Very nice!!!
I am another that has no use for a can opener. I like the screwdriver blade on the opener though. I need to find someone (hint hint) that could make a tool to go in that place that is a sturdy screwdriver with the side of said tool turned into a nail file. That would probably be my perfect tool. A Pioneer X with file/screwdriver replacing the can opener/screwdriver.
Sent from my iPhone using Tapatalk
-
It hurts to see all these beautiful mods and innovations.

-
That's a good one Syph.

-
Swiss champ with tumbled Ti liners and scales. Pruner blade, mokume cross and scale drawer. Full loaded. :D
-
@Syph007 said:
Swiss champ with tumbled Ti liners and scales. Pruner blade, mokume cross and scale drawer. Full loaded. ??? ???But nobody ever wants the Fish Scaler - For the width of the blade I'd always be tempted to include it!
I have found it very useful a couple of times.
Note to self: Make post to get badge!!The tool I'd be tempted to drop would be the pliers - Although if I was going for a Champ - You might as well keep them too - What's another 3mm ??? ;)
-
Swiss champ with tumbled Ti liners and scales. Pruner blade, mokume cross and scale drawer. Full loaded. :D
Does the pruner blade need any work to fit in place of the small blade? Your knives keep improving nicely!
The blade doesn't need altering but the spacer beside it is thinner than normal that's all.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
