The Hacked Leatherman Owners Club.
-
Welcome to

Seems the Raptor strap cutter would work
but never seen it down and am not for sure :-\ Plus you would either have to track the part down as you are trying or buy a Raptor for the part :ahhh Either way good luck in the search and the mod

-
20 minute Style PS/CS mod to remove the useless carabiner and add a split ring instead.
Tools needed: wire cutters, file, knife or hacksaw blade
-
Carefully cut the black plastic at the base of tweezers, about 2 mm below the rivet, with a knife or hacksaw.
-
Use wire cutters to snip the carabiner at the base of the cutouts (4 places). These can just be snapped off with the cutters.
-
File down the jagged stubs remaining until they are roughly even with the plastic piece you cut in step 1.
-
Add split rings as shown in the photo.
Never lose your Style PS or CS again because it fell off the keyring.

-
-
@Shane O'Neal said:
20 minute Style PS/CS mod to remove the useless carabiner and add a split ring instead.Tools needed: wire cutters, file, knife or hacksaw blade
-
Carefully cut the black plastic at the base of tweezers, about 2 mm below the rivet, with a knife or hacksaw.
-
Use wire cutters to snip the carabiner at the base of the cutouts (4 places). These can just be snapped off with the cutters.
-
File down the jagged stubs remaining until they are roughly even with the plastic piece you cut in step 1.
-
Add split rings as shown in the photo.
Never lose your Style PS or CS again because it fell off the keyring.
Erm.. Do you really need to remove the carabiner to add the ring? There's already holes to attach the rings? Imo the carabiner serves as a extended handle to use the scissors.. I dun use the carabiner but definitely like it there for its longer handle..
-
-
Hello all,
At the beginning of 2018, I became a new owner of the Leatherman Wave :-) .
It's really a great tool !!
When I see all mods/hacks, one thing are really cool, it's replace file or blade by a bigger scissors .
Did you have a really good howto with marketplace to buy the scissors ?Thank's in advance.
-
@Sam Lim said:
Erm.. Do you really need to remove the carabiner to add the ring? There's already holes to attach the rings? Imo the carabiner serves as a extended handle to use the scissors.. I dun use the carabiner but definitely like it there for its longer handle..It's a personal preference. I hated that carabiner.
-
Welcome to
Shane and Draleg 
I have never done the Wave mod you speak of Draleg so hopefully someone who has will be along to help you out

-
0203181421a by Poncho 65, on Flickr -
Im gonna do Ebay hacked on new Wave .. hahahha love it Stay tuned
-
-
-
Nice one Hi
I dislike chisel grind about the same as the combo edge blade :D -
hy friends,
i need advice.
i want to adapt the scissor from Wingman onto Wave. What should i consider, where to grind first etc. i don't want to mess the scissors -
I would go with SAK Scissors
/topic/64924 -
This is my LM crunch knifeless
Fitted with LM wave scissors
And a LM kick pocket clip


-
@Raoul Octav said:
hy friends,
i need advice.
i want to adapt the scissor from Wingman onto Wave. What should i consider, where to grind first etc. i don't want to mess the scissorsSince the diameter of the Wave pivot screw is biger (1mm or less) than the Wingman, you need to grind the pivot hole on the scissors just a bit, a Dremel tool will do the trick. Don't grind to much because you will ruin the scissors, just make sure to grind a little bit at a time while checking the Wave pivot screw until it goes through the hole.
Good luck!

-
-
@Obi1shinobee said:
I would go with SAK Scissors
/topic/64924Good link right there

-
@Raoul Octav said:
hy friends,
i need advice.
i want to adapt the scissor from Wingman onto Wave. What should i consider, where to grind first etc. i don't want to mess the scissorsHelp with wingman scissors in a TTi and Leatherman Wingman Scissors.
-
Very nice write ups Zoidberg

-
Hello, Me again.
Finnaly did it, i went to the Dark Side, will go darker once i experiment wit ferric chloride
Thank you guys,
Modding
https://youtu.be/gPVHZCcDeOY
Dismantling, for those wo just got born. Interesting debate theme, a multitool user knows how to dismantle his tool?
https://youtu.be/qf3MMV9H_Wk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

