Advice on fixing wonky layers
-
Great to hear!
-
Nice one PO'B
Is it a bladeless explorer or still a bladeless Woodsman? :DLooking forward to pics

-
Doh!
Bladeless Woodsman, mk 2.Thanks everyone, for the advice and cheers.





-
Oh, I forgot to mention, the can opener can't open cans the regular way anymore, due to its position.
It still works in a pinch, and I'm happy with the compromise.

-
That looks great PO'B

Very inspiring - I may have to break out the tools and make me a bladeless SAK too.

-
@magentus said:
That looks great PO'B
Very inspiring - I may have to break out the tools and make me a bladeless SAK too.


Spoiler:
I did it the easy way and put the openers over the corkscrew and blade spring. It means the nail nick is on the wrong side, and its hard to open cans, but its easy to do at least. :DUsing the new stamped blade liner, you only need one brass washer, of approximately .39mm thickness, for the bottle opener. I made mine from .4mm brass sheet I found at the hobby shop.
Using the old non stamped liner, you need an extra washer of same thickness (for the can opener).
I hope I am making sense.
And then there is all the other ways to make a bladeless SAK, most of them beyond me. :-\
-
Bladeless Woodsman, MK3???????
I don't know if it qualifies as a woodsman anymore.
What do you think? And if not, what is it? 
Spoiler:
More details:
</post/1553896>It has wonky liners again.

More specifically, the scissors and corresponding outer liner are wonky(to a lesser extent than last time, when I started this thread). I think its a bent pin or bad pre-preening.
As the only tools on that pin are the scissors and mag glass, it should be fine for now.It has a hook now!!!!

-
I was thinking about a mod last night that I want to do and starting to se how it all will work together I ran in to some headache with the backsprings. I want to have the opening layer with a corkscrew instead of the awl, so far so good but the corkscrew sits on the knife layer and those springs are quite different.
Which backspring did you use? My first thought was to use the opening layer spring and remove some material in the end but any tips and tricks would be welcome [emoji5]
[It's not failure if you learn something from it]
-
@kottskrapa said:
I was thinking about a mod last night that I want to do and starting to se how it all will work together I ran in to some headache with the backsprings. I want to have the opening layer with a corkscrew instead of the awl, so far so good but the corkscrew sits on the knife layer and those springs are quite different.Which backspring did you use? My first thought was to use the opening layer spring and remove some material in the end but any tips and tricks would be welcome [emoji5]
[It's not failure if you learn something from it]
This any use?

</post/1552402>
Tell me if you have unanswered questions afterwards.
And good luck.
-
@Pablo O'Brien said:
I was thinking about a mod last night that I want to do and starting to se how it all will work together I ran in to some headache with the backsprings. I want to have the opening layer with a corkscrew instead of the awl, so far so good but the corkscrew sits on the knife layer and those springs are quite different.
Which backspring did you use? My first thought was to use the opening layer spring and remove some material in the end but any tips and tricks would be welcome [emoji5]
[It's not failure if you learn something from it]
This any use?

/post/1552402
Tell me if you have unanswered questions afterwards.
And good luck.
Thanks mate! [emoji3]
[It's not failure if you learn something from it]
-
@Pablo O'Brien said:
I was thinking about a mod last night that I want to do and starting to se how it all will work together I ran in to some headache with the backsprings. I want to have the opening layer with a corkscrew instead of the awl, so far so good but the corkscrew sits on the knife layer and those springs are quite different.
Which backspring did you use? My first thought was to use the opening layer spring and remove some material in the end but any tips and tricks would be welcome [emoji5]
[It's not failure if you learn something from it]
This any use?

/post/1552402
Tell me if you have unanswered questions afterwards.
And good luck.
Thanks mate! [emoji3]
[It's not failure if you learn something from it]
No problem.

-
I’ll interject some wisdom. The pins are surely bent. You need some sort of jig for assembly. If you can’t make one use a stack of liners taped together. The pins need to be longer than the finished knife.
The springs are also slightly wider than the tools so they will work.
Here’s my advice.
Hard to explain but I’ll try.
Put pins in jig first.
Outer liner first, then the tool spring, followed by the tools but don’t force them in just yet. Do the non corkscrew or backside philips layer last not this layer. One side of the tools will go in and one side won’t. That’s what you need in order for this to work.
Add a liner and push it down tight as you can. Then use and small pin punch and load the other tool. This will support the pins as you assemble.
After all is together all the tools should still be in the open position. Hold it tight or tape the knife up so it don’t blow apart, not fun if it does.
Then pin the outer pins first, then one with the tools. Don’t hammer them closed just yet, just enough to hold the knife together for now
Next donthe center pivot pin. Then the backside tool pin. This should hold the knife together. Now you can check to see if the tools work correctly and that the pins aren’t bent. Don’t let them snap shut as they can damage the liners
After that’s done and everything looks good. Start pinning it tools side first. They should be very slightly loose. That’s normal. Then do the backside tool pin.
After that the middle pin. This is the tricky one. It’s only purpose is to help support the springs. It should be tight enough to barley spin. Then check snap on each tool separately one at a time. They should all fall correctly in place.
That should correct any issues you have. Hope this all makes sense and is helpful.Sent from my iPhone using Tapatalk
-
Thanks for your input.

I learned about the not bending the pins bit already, but the bit about the peening I will keep in mind from now on.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login