Used Leatherman PST (Lynn's $10 MT Challenge)
-
@ReamerPunch said:
Very appropriate to test a PST now, too.
With the collector's edition one released, and a general thought of "how much would YOU pay for a PST", I had to bite my tongue while thinking "I guess at least $8".

@ThePeacent said:
these tools used are a bargain most times, they come back to business in a breeze with some TLC. Also, this tool you tested was 21 years old, how many Ozark Trails, Les Stroud or Mossy Oak would work as good after two decades...I bet few of them
While this is very true, it's also true that the tool as purchased was almost unusable. It's not just a question of how long they last. It's a question of whether or not you have the time and interest in doing the restoration work. If I had worked a minimum wage job for the amount of time I worked to fix this thing, I could have bought a new Rebar. Okay, maybe a gently used Rebar. :D
-
@Lynn LeFey said:
@ReamerPunch said:
Very appropriate to test a PST now, too.
While this is very true, it's also true that the tool as purchased was almost unusable. It's not just a question of how long they last. It's a question of whether or not you have the time and interest in doing the restoration work. If I had worked a minimum wage job for the amount of time I worked to fix this thing, I could have bought a new Rebar. Okay, maybe a gently used Rebar. :D
fair enough.
That's why when the tools you tested drew blood in this challenge and I read about how you spent "30 mins" :o sharpening a blade or nearly and hour between those two SAK's badly ground and sharpened edges, I thought to myself that not even I spend that much time on edges,* especially if they're from cheap knives*. :ahhhIf they're so damaged or bad, I put them through the Dremel :D and forget about "surgical precision sharpening"
-
@ThePeacent said:
That's why when the tools you tested drew blood in this challenge and I read about how you spent "30 mins" :o sharpening a blade or nearly and hour between those two SAK's badly ground and sharpened edges, I thought to myself that not even I spend that much time on edges,* especially if they're from cheap knives*. :ahhhIf they're so damaged or bad, I put them through the Dremel :D and forget about "surgical precision sharpening"
The time I spent is for two reasons. Until a few days ago, I didn't have a good way to sharpen a blade very quickly, with any degree or precision. So it was a slow process. Second, I don't want my results of 'this blade sucks' to be because I did a half-smurfed job.
However, I have a new sharpener that should speed things up for future testing.
-
@ThePeacent said:
That's why when the tools you tested drew blood in this challenge and I read about how you spent "30 mins" :o sharpening a blade or nearly and hour between those two SAK's badly ground and sharpened edges, I thought to myself that not even I spend that much time on edges,* especially if they're from cheap knives*. :ahhhI had a similar thought.
Then I remembered times in my life where $10 was food for three or four days. If I could get a SAK or LM for less than $10 that I had a high degree of confidence that I could recover, I would have. Even if I had to make the soapy water by boiling wood ash and some grease.
They took time to recover. If I was back in those kinds of circumstances again, I MIGHT go with the knock off pliers based because it performed OK. But back then, there weren't a lot of knock off multitools other than Gerber, and the only cheap options to a SAK were things like Lynn's old Colman and "Q-army" knives.And I still think I would think about recovering the LM or a SAK.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login