Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Bending a LM tool

Scheduled Pinned Locked Moved The Mod Squad
92 Posts 1 Posters 5.0k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Bending a LM tool
Bending a LM tool
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Vidar Offline
    Vidar
    Posts: 2,605
    Vidar Offline
    Vidar
    wrote on last edited by
    #57 Quote Reply

      Specifications on various alloys usually have some information and specific recipes for annealing and hardening treatments of that particular steel quality. For 420 stainless steel an example can be found at http://www.aksteel.com/pdf/markets_products/stainless/martensitic/420_data_sheet.pdf

      1 Reply Last reply
      • SteveC Offline
        SteveC
        Global Moderators
        Posts: 73,535
        SteveC Offline
        SteveC
        Global Moderators
        wrote on last edited by
        #58 Quote Reply

          Would hardening in oil leave it less brittle ?

          1 Reply Last reply
          • Vidar Offline
            Vidar
            Posts: 2,605
            Vidar Offline
            Vidar
            wrote on last edited by Vidar
            #59 Quote Reply

              @SteveC said:
              Would hardening in oil leave it less brittle ?

              According to the spec sheet for 420 stainless steel it should be quenched in warm oil when hardening. As steels can be optimized for hardening with various media I think following the steel manufacturers directions might be a good idea. (Including tempering after quenching to make the right balance between hard/brittle and tough/ flexible).

              The overall idea is to quench quick enough to get the part hardened to the required depth but no faster than necessary. Faster cooling increases residual stresses and thus the risk of cracks or deformation. Faster cooling also tends to make harder and more brittle parts.

              Water has a lower boiling point than oil and hence cools the part faster. So yes, it will likely be less brittle by oil quenching instead.

              (Heat treatment and metallurgy are huge subjects on their own. I'm certainly no speSmurfpillst in either by any means, but the above is my big picture understanding summarized in a few lines).

              1 Reply Last reply
              • zoidberg Offline
                zoidberg
                Posts: 38,161
                zoidberg Offline
                zoidberg
                wrote on last edited by
                #60 Quote Reply

                  I did want to use oil but water was there so I went with that.

                  Any ideas for torture tests?

                  1 Reply Last reply
                  • Rebelgium Offline
                    Rebelgium
                    Posts: 50
                    Rebelgium Offline
                    Rebelgium
                    wrote on last edited by
                    #61 Quote Reply

                      @zoidberg said:
                      I did want to use oil but water was there so I went with that.

                      Any ideas for torture tests?

                      Like the video posted earlier I'm going to use the bent and sharpened canopener as a spoon carving knife (which can still kind of open a can). Both functions are not ideal, I know, but I'm aiming for an ultralight wildcamping tool. And going ultralight is all about compromises.

                      So while using this tool there will be some bending forces applied. So the brittleness is an important factor.

                      I'm trying to think of a good test where the result will not be subjective. Eg "I think it felt kind of strong enough... "
                      Maybe cold bending it again? We know the factory steel could be bent 5mm before breaking. So if the bent tool snaps at less, we know it's harder & more brittle than factory. And vice versa

                      1 Reply Last reply
                      • Wspeed Offline
                        Wspeed
                        Posts: 76,225
                        Wspeed Offline
                        Wspeed
                        wrote on last edited by
                        #62 Quote Reply

                          @zoidberg said:
                          I did want to use oil but water was there so I went with that.

                          Any ideas for torture tests?

                          How about a twisting test? :think:
                          You tested piercing it on a tin can
                          And cold bending
                          So what about placing it in a vice and
                          Use vice grips to test how much degrees it will go :tu:

                          1 Reply Last reply
                          • Vidar Offline
                            Vidar
                            Posts: 2,605
                            Vidar Offline
                            Vidar
                            wrote on last edited by Vidar
                            #63 Quote Reply

                              @Rebelgium said:
                              I'm trying to think of a good test where the result will not be subjective. Eg "I think it felt kind of strong enough... "

                              A good test might simply be if the tool actually works as intended? Zoidbergs bend seems to work great? The process itself seems kind of variable so once you find a working piece you might want to keep it rather than destructive test it :angel:

                              If you have a small precise heat source (since this is a small part) you can try bending it purely with heat distortion. Draw a few parallel guidelines perpendicular to the the tool length on the inside of what will become the curving. Then apply heat along and parallel to those lines, and on that side only. If possible try to help the opposite side to stay cooler - clamping or pressing some copper or aluminium to it will help with that.

                              As the metal heats it will expand on the heated side and somewhat less on the cold side. The bend is then initially the wrong way, but as it cools again the heated side will also contract more than the cooler side and you'll get a bend the right way. If you heat along parallel lines it should bend fairly cleanly without twisting.

                              This can be a fairly slow and well controlled process. The part is quite small so you might need a jewelers torch, tig welding equipment or other means of applying controlled heat along narrow lines. The part also has some uneven thickness due to the edge so it might get somewhat twisted. Which might work out great - or not.

                              And last, but certainly not least, don't blame me if it all goes smurf :D

                              1 Reply Last reply
                              • ironraven Offline
                                ironraven
                                Posts: 3,071
                                ironraven Offline
                                ironraven
                                wrote on last edited by
                                #64 Quote Reply

                                  Zoidberg, it looks nutty, but it looks like... well... it was made for you. Now you have a can openning claw. What more could a happy mollusc ask for?

                                  1 Reply Last reply
                                  • zoidberg Offline
                                    zoidberg
                                    Posts: 38,161
                                    zoidberg Offline
                                    zoidberg
                                    wrote on last edited by
                                    #65 Quote Reply

                                      @Rebelgium said:

                                      @zoidberg said:

                                      Any ideas for torture tests?

                                      Like the video posted earlier I'm going to use the bent and sharpened canopener as a spoon carving knife (which can still kind of open a can). Both functions are not ideal, I know, but I'm aiming for an ultralight wildcamping tool. And going ultralight is all about compromises.

                                      @Vidar said:

                                      @Rebelgium said:

                                      I'm trying to think of a good test where the result will not be subjective. Eg "I think it felt kind of strong enough... "

                                      A good test might simply be if the tool actually works as intended? Zoidbergs bend seems to work great?

                                      Thought before it gets broken I should probably see how well it performs when carving a spoon.

                                      After cutting a recently fallen branch down to length I used the plain blade to shape out a spoon blank.
                                      And that is where the fun ended. First the camera battery went flat, great. Secondly the bent opener was all wrong.
                                      Between the bevel direction, the curve, the bottle opener hook and the can opener point, it is near impossible to scoop out wood.
                                      I stuck at it for a while but it was just an exercise in frustration.

                                      1 Reply Last reply
                                      • zoidberg Offline
                                        zoidberg
                                        Posts: 38,161
                                        zoidberg Offline
                                        zoidberg
                                        wrote on last edited by
                                        #66 Quote Reply

                                          Had a little time today so annealed it again and put a bevel on the outside edge. This time I hardened it in oil.

                                          1 Reply Last reply
                                          • zoidberg Offline
                                            zoidberg
                                            Posts: 38,161
                                            zoidberg Offline
                                            zoidberg
                                            wrote on last edited by
                                            #67 Quote Reply

                                              1 Reply Last reply
                                              • zoidberg Offline
                                                zoidberg
                                                Posts: 38,161
                                                zoidberg Offline
                                                zoidberg
                                                wrote on last edited by
                                                #68 Quote Reply

                                                  Installed and ready but waiting until I have more free time.

                                                  1 Reply Last reply
                                                  • Wspeed Offline
                                                    Wspeed
                                                    Posts: 76,225
                                                    Wspeed Offline
                                                    Wspeed
                                                    wrote on last edited by
                                                    #69 Quote Reply

                                                      Looking good so far Zoidberg :tu: :like:

                                                      1 Reply Last reply
                                                      • Vidar Offline
                                                        Vidar
                                                        Posts: 2,605
                                                        Vidar Offline
                                                        Vidar
                                                        wrote on last edited by
                                                        #70 Quote Reply

                                                          @zoidberg said:
                                                          Had a little time today so annealed it again and put a bevel on the outside edge. This time I hardened it in oil.

                                                          Looking good! I have faith :tu:

                                                          1 Reply Last reply
                                                          • SteveC Offline
                                                            SteveC
                                                            Global Moderators
                                                            Posts: 73,535
                                                            SteveC Offline
                                                            SteveC
                                                            Global Moderators
                                                            wrote on last edited by
                                                            #71 Quote Reply

                                                              :popcorn:

                                                              1 Reply Last reply
                                                              • Wspeed Offline
                                                                Wspeed
                                                                Posts: 76,225
                                                                Wspeed Offline
                                                                Wspeed
                                                                wrote on last edited by
                                                                #72 Quote Reply

                                                                  @SteveC said:
                                                                  :popcorn:

                                                                  +1 :popcorn:

                                                                  1 Reply Last reply
                                                                  • zoidberg Offline
                                                                    zoidberg
                                                                    Posts: 38,161
                                                                    zoidberg Offline
                                                                    zoidberg
                                                                    wrote on last edited by
                                                                    #73 Quote Reply

                                                                      1 Reply Last reply
                                                                      • zoidberg Offline
                                                                        zoidberg
                                                                        Posts: 38,161
                                                                        zoidberg Offline
                                                                        zoidberg
                                                                        wrote on last edited by
                                                                        #74 Quote Reply

                                                                          1 Reply Last reply
                                                                          • zoidberg Offline
                                                                            zoidberg
                                                                            Posts: 38,161
                                                                            zoidberg Offline
                                                                            zoidberg
                                                                            wrote on last edited by
                                                                            #75 Quote Reply

                                                                              1 Reply Last reply
                                                                              • zoidberg Offline
                                                                                zoidberg
                                                                                Posts: 38,161
                                                                                zoidberg Offline
                                                                                zoidberg
                                                                                wrote on last edited by
                                                                                #76 Quote Reply

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  • 5
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Bending a LM tool
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0