How Plier pivots work?
-
Interesting, however, this only raises more questions :D
How is it possible to twist the pivot to tighten the pliers if they are only pressed in place? And if they are pressed in the same way and the same specifications, shouldn't they all be about the same resistance in the action of the pliers?
-
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Interesting, however, this only raises more questions :D
How is it possible to twist the pivot to tighten the pliers if they are only pressed in place? And if they are pressed in the same way and the same specifications, shouldn't they all be about the same resistance in the action of the pliers?
I'm not entirely sure what you're asking, so I'll throw an answer forwards, and see how much sticks....
If you imagine that the outer faces of the pliers head are countersunk, and when the pivot pin is rivetted in, it forms into the countersunk areas and pulls the two halves of the head together. This is done while the pivot pin is hot, and as it cools, the pin contracts and increases resistance. Variations in the rivetting, and in the pins themselves, will leave heads with some variation of initial resistance. As the pliers get used, both the swaged ends of the pin, and the cupped area of the plier heads wear, and the head becomes looser. Using a centre punch to cold swage the metal out, takes the slack back out of the plier heads.
I'm not sure if this is the answer you are looking for, but it might help us narrow it down to the bit that you aren't understanding.
-
@50ft-trad said:
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Interesting, however, this only raises more questions :D
How is it possible to twist the pivot to tighten the pliers if they are only pressed in place? And if they are pressed in the same way and the same specifications, shouldn't they all be about the same resistance in the action of the pliers?
I'm not entirely sure what you're asking, so I'll throw an answer forwards, and see how much sticks....
If you imagine that the outer faces of the pliers head are countersunk, and when the pivot pin is rivetted in, it forms into the countersunk areas and pulls the two halves of the head together. This is done while the pivot pin is hot, and as it cools, the pin contracts and increases resistance. Variations in the rivetting, and in the pins themselves, will leave heads with some variation of initial resistance. As the pliers get used, both the swaged ends of the pin, and the cupped area of the plier heads wear, and the head becomes looser. Using a centre punch to cold swage the metal out, takes the slack back out of the plier heads.
I'm not sure if this is the answer you are looking for, but it might help us narrow it down to the bit that you aren't understanding.
That is good solid information, thank you! However, how come that turning the pivot itself tightens the action?
-
Thanks Trad,
I thought so myself until I saw this...
</post/1606839>
What do you think?

-
@50ft-trad said:
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Interesting, however, this only raises more questions :D
How is it possible to twist the pivot to tighten the pliers if they are only pressed in place? And if they are pressed in the same way and the same specifications, shouldn't they all be about the same resistance in the action of the pliers?
I'm not entirely sure what you're asking, so I'll throw an answer forwards, and see how much sticks....
If you imagine that the outer faces of the pliers head are countersunk, and when the pivot pin is rivetted in, it forms into the countersunk areas and pulls the two halves of the head together. This is done while the pivot pin is hot, and as it cools, the pin contracts and increases resistance. Variations in the rivetting, and in the pins themselves, will leave heads with some variation of initial resistance. As the pliers get used, both the swaged ends of the pin, and the cupped area of the plier heads wear, and the head becomes looser. Using a centre punch to cold swage the metal out, takes the slack back out of the plier heads.
I'm not sure if this is the answer you are looking for, but it might help us narrow it down to the bit that you aren't understanding.
That is good solid information, thank you! However, how come that turning the pivot itself tightens the action?
Two answers:
-
Some pivots are threaded, not rivetted
-
It depends how well the cups are formed that the rivet is displaced into. If the cups were uneven, turning the pivot can take some slack out by getting a thicker part of the rivet head to seat in a shallower part of the cup, but the rivets will only be contacting in a reduced area, so the fix will likely only be short lived
-
-
You can see one half of the pliers here at 4:03
http://www.youtube.com/watch?v=Tx4QruhI0F0&t=243s]
and you can just about make out the countersunk hole for the rivet a little later on. -
I really do wonder if Leatherman pliers have screw in pivots...
-
I don't believe so. I think they're riveted.
-
Yup, LMs are riveted. Threaded plier pivots tend to have tell tale signs of driving the thread, either as a hex socket, or holes for a pin spanner. This makes the pivot adjustable, but also a lot more costly to make, not just in terms of having to make two mating speSmurfpillsed fasteners for the pivot, but also needing the cups in the head to be precisely machined - none of which is needed on a rivetted construction
-
@50ft-trad said:
@50ft-trad said:
[quote author=Smashie link=topic=76191.msg1648402#msg1648402 date=1519925737]
https://www.youtube.com/watch?v=f985LH0ix3wInteresting, however, this only raises more questions :D
How is it possible to twist the pivot to tighten the pliers if they are only pressed in place? And if they are pressed in the same way and the same specifications, shouldn't they all be about the same resistance in the action of the pliers?
I'm not entirely sure what you're asking, so I'll throw an answer forwards, and see how much sticks....
If you imagine that the outer faces of the pliers head are countersunk, and when the pivot pin is rivetted in, it forms into the countersunk areas and pulls the two halves of the head together. This is done while the pivot pin is hot, and as it cools, the pin contracts and increases resistance. Variations in the rivetting, and in the pins themselves, will leave heads with some variation of initial resistance. As the pliers get used, both the swaged ends of the pin, and the cupped area of the plier heads wear, and the head becomes looser. Using a centre punch to cold swage the metal out, takes the slack back out of the plier heads.
I'm not sure if this is the answer you are looking for, but it might help us narrow it down to the bit that you aren't understanding.
That is good solid information, thank you! However, how come that turning the pivot itself tightens the action?
Two answers:
-
Some pivots are threaded, not rivetted
-
It depends how well the cups are formed that the rivet is displaced into. If the cups were uneven, turning the pivot can take some slack out by getting a thicker part of the rivet head to seat in a shallower part of the cup, but the rivets will only be contacting in a reduced area, so the fix will likely only be short lived
[/quote]
Now that makes sense

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
