Gerber MP400 refreshed version.
-
@Sam Lim said:
On the other hand, I am a bit worried inside is hollow and it will leave some unintended gap..
It's not hollow.
It's definitely not. :) Thanks to gerleatherberman for the idea.


Did a few modification on it today... Above was one. ;)
A major change to the pliers head. I have to admit I went a bit too far on this one. I was trying out something else but didn't work out. So I have to ground down quite a bit to correct the error.. Quick dip in acid to dull back the pliers to match the handles.


Another modification was to add a locking notch so that the needle tip does not slide out and stab me when I sit or squat down. Its on the opposite side of the clip. So when I pull out the baby, my thumb will be right at the spot to unlock it.

Cheers! Thanks everyone for the positive inputs!

-
Great stuff Sam!
Love what you're doing dude 
-
improving an already excellent tool


-
Oh my that is awesome, Sam! You're welcome for the idea, but wow did you do a nice job!
On a side note, the plier head is similar to the way I regrind my broken tipped needle noses at work. Similar to a SOG plier head. Very nice for fine work!So, when ya going to start mass producing these 'MP400Lim' MTs?

-
@gerleatherberman said:
Oh my that is awesome, Sam! You're welcome for the idea, but wow did you do a nice job!
On a side note, the plier head is similar to the way I regrind my broken tipped needle noses at work. Similar to a SOG plier head. Very nice for fine work!So, when ya going to start mass producing these 'MP400Lim' MTs?

Visit my booth at SHOT show 2019. Lol..

Now that you reminded me of the SOG PPP, I dun feel so bad about grinding down on the plier tip.. Yes, the narrowed tip is really suited for fine work.

-
@Sam Lim said:
Oh my that is awesome, Sam! You're welcome for the idea, but wow did you do a nice job!
On a side note, the plier head is similar to the way I regrind my broken tipped needle noses at work. Similar to a SOG plier head. Very nice for fine work!So, when ya going to start mass producing these 'MP400Lim' MTs?

Visit my booth at SHOT show 2019. Lol..

I'll be looking for it there.

-
@Sam Lim said:
Oh my that is awesome, Sam! You're welcome for the idea, but wow did you do a nice job!
On a side note, the plier head is similar to the way I regrind my broken tipped needle noses at work. Similar to a SOG plier head. Very nice for fine work!So, when ya going to start mass producing these 'MP400Lim' MTs?

Visit my booth at SHOT show 2019. Lol..

I'll be looking for it there.

I will be somewhere outside the venue, setting up shop. Have to be fast though, the guards would probably chase me away once they spot me..

-
A little how-to on installing the clip.
Its a standard Wave/charge clip with a little modification. Somewhere in the middle of the screw post, u will need to cut out a groove for the pocket clip to slide in. See pic and you will get it. A little precision cutting. Go slow. A proper nice cut will minimize any side to side play. On the clip, ground off any excess on the sides and leave some allowance on the bottom 2 "feets". Now side to side is settled if you have done the cut nicely.
Red is the area you need to cut groove. Green is the position of the pocket clip

Next you have prevent it from moving up and down or sliding off. What I did was, I torch the "feets"one by one. When it hot/soft enough, I hammer the buggers to wrap it around the pivot.
See, you are done. Easy as pie.


-
@Sam Lim said:
A little how-to on installing the clip.Its a standard Wave/charge clip with a little modification. Somewhere in the middle of the screw post, u will need to cut out a groove for the pocket clip to slide in. See pic and you will get it. A little precision cutting. Go slow. A proper nice cut will minimize any side to side play. On the clip, ground off any excess on the sides and leave some allowance on the bottom 2 "feets". Now side to side is settled if you have done the cut nicely.
Red is the area you need to cut groove. Green is the position of the pocket clip

Next you have prevent it from moving up and down or sliding off. What I did was, I torch the "feets"one by one. When it hot/soft enough, I hammer the buggers to wrap it around the pivot.
See, you are done. Easy as pie.


Nice! Some good thinking there [emoji16]
Sent fra min FRD-L09 via Tapatalk
-
@Sam Lim said:
A little how-to on installing the clip.
Its a standard Wave/charge clip with a little modification. Somewhere in the middle of the screw post, u will need to cut out a groove for the pocket clip to slide in. See pic and you will get it. A little precision cutting. Go slow. A proper nice cut will minimize any side to side play. On the clip, ground off any excess on the sides and leave some allowance on the bottom 2 "feets". Now side to side is settled if you have done the cut nicely.
Red is the area you need to cut groove. Green is the position of the pocket clip

Next you have prevent it from moving up and down or sliding off. What I did was, I torch the "feets"one by one. When it hot/soft enough, I hammer the buggers to wrap it around the pivot.
See, you are done. Easy as pie.


Nice! Some good thinking there [emoji16]
Sent fra min FRD-L09 via Tapatalk
:)
Just happened that that particular side of the pivot is in a fixed position. That helps alot. And because that clip is already jammed between the frame and post screw, you will be able to still do some adjustment to the tightness of the implements without much affecting the clip.

-
Nicely done as always

-
@Sam Lim said:
@Sam Lim said:
A little how-to on installing the clip.
Its a standard Wave/charge clip with a little modification. Somewhere in the middle of the screw post, u will need to cut out a groove for the pocket clip to slide in. See pic and you will get it. A little precision cutting. Go slow. A proper nice cut will minimize any side to side play. On the clip, ground off any excess on the sides and leave some allowance on the bottom 2 "feets". Now side to side is settled if you have done the cut nicely.
Red is the area you need to cut groove. Green is the position of the pocket clip

Next you have prevent it from moving up and down or sliding off. What I did was, I torch the "feets"one by one. When it hot/soft enough, I hammer the buggers to wrap it around the pivot.
See, you are done. Easy as pie.


Nice! Some good thinking there [emoji16]
Sent fra min FRD-L09 via Tapatalk
:)
Just happened that that particular side of the pivot is in a fixed position. That helps alot. And because that clip is already jammed between the frame and post screw, you will be able to still do some adjustment to the tightness of the implements without much affecting the clip.

Great idea!
Sent fra min FRD-L09 via Tapatalk
-
Thanks for the very clear and clever explanation Sam
Great work. -
Are you planning to do anything
else to your MP400 Sam Lim

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
